P S I T019-02 TireView Receiver Installation Guide

CAUTION: Proper installation of the repeater is
crucial for system functionality. Failure to install the repeater
correctly could void the warranty.

Mount the TireView repeater on the tractor/truck or trailer in
the recommended location. The unit is waterproof and can be
installed inside or outside.

Ensure the repeater harness reaches the power source, typically
the battery box or battery access area.
Connect the 12V+ (Red) and 12V- (Black) wires with ring
terminals from the repeater to the battery terminals.

NOTE: The red light on the repeater will
illuminate when it receives power, indicating proper functioning.
No further setup is required for the repeater.

Frequently Asked Questions (FAQ)

Q: Do I need to pair sensors with the receiver?

A: No, sensors are not paired with the receiver. Please refer to
the separate installation manual for sensor pairing
instructions.

“`

View Fullscreen

TireView Receiver, Harness and Repeater Installation
Truck/Tractor Applications
INSTALLATION MANUAL
TireView Receiver, Harness and Repeater Installation
Vehicles with GEOTAB GO Device

Truck/Tractor Applications

www.psitireinflation.com/resources#tpms-resources
© 2025 Pressure Systems International, LLC. A Clarience Technologies Company.

PSI How To: Geotab TireView LIVE Install Video

T019-02 Rev 08-25

TireView Receiver, Harness and Repeater Installation
Truck/Tractor Applications
About this Manual This manual provides installation and maintenance procedures for TireView® TPMS by P.S.I. Use the procedures in this manual to install the system on commercial vehicles equipped with the GEOTAB GO Device. Before You Begin
CAUTION: DO NOT PERFORM UNAUTHORIZED MAINTENANCE OR REPAIR PROCEDURES, OR INSTALL NON-P.S.I.® COMPONENTS ON ANY P.S.I. ® SYSTEM. THIS CAN VOID THE WARRANTY.
1. Read and understand all instructions and procedures before service to components begins. 2. Read and observe all Warning and Caution alert messages in this publication. They provide information that can
prevent personal injury, damage to components, or both. 3. Follow the P.S.I. installation, maintenance, service, and troubleshooting guidelines. 4. Use special tools, when required, to avoid personal injury and damage to components.
Hazard Alert Messages and Torque Symbols
WARNING: A Warning alerts the technician to an instruction or procedure that must be followed to avoid personal injury and damage to components.
CAUTION:
A Caution alerts the technician to an instruction or procedure that must be followed to avoid damage to components.
TORQUE REQUIRED:
The torque symbol alerts the technician to tighten fasteners to a specified torque value.
Additional Information Visit the Resource section at www.psitireinflation.com to access and request additional information. Call P.S.I.® at 210.222.1926 (United States and Canada) or email info@psitireinflation.com or techsupport@psitireinflation.com.
Introduction
The P.S.I.® TireView® Tire Pressure Monitoring System (TPMS) is designed to monitor air pressure and temperature in the tire. It is only for added safety and not meant to replace regular tire maintenance and exercise of reasonable care when operating a motor vehicle. The system cannot prevent accidents nor will P.S.I.® be responsible for damage or injury due to (a) improper use,(b) failure to follow the product manufacturer’s instructions or to perform preventative maintenance, (c) unauthorized repair or modifications, (d) use of products beyond their useful life, or (e) external causes such as accidents, abuse, or other actions or events outside of P.S.I.® control.

A Clarience Technologies Company.

T019-02 Rev 08-25

TireView Receiver, Harness and Repeater Installation
Truck/Tractor Applications

Introduction
This manual is intended to provide guidance when installing the TPMS Receiver, Harness and Repeater accessories for TPMS system on vehicles equipped with the GEOTAB GO Device. Your configuration may vary due to type of equipment. Consult your support team for guidance.

Receiver, Harness and Repeater Components
PART DESCRIPTION
TireView Repeater
· Signal repeater boosts sensor signal to receiver
· MUST be installed to ensure sensor signal reliability
· 15′ lead, 3/8″ ring terminals, in-line replaceable 2-amp mini blade fuse
· 12V+(Red) and 12V-(Black) wires for power connection
TireView TPMS Telematics Receiver
· Geotab-specific receiver · Easy plug-n-play installation · Installs into Geotab GO Device utilizing
TireView harness · Requires Geotab IOX Harness (supplied
separately) · Sensors pair to receiver utilizing
Goodyear TPMS PLUS app*
TireView Amp to DB9 Harness
· Amp connector inserts into TireView receiver
· DB9 connector inserts into Geotab IOX harness
· 12V+(Red) and 12V-(Black) wires for power connection to Geotab IOX harness

EXAMPLE
AMP Connector
DB9 Connector

Geotab IOX RS232F Harness (supplied separately)
· Plugs into Geotab GO Device located in cab of vehicle

NOTE: FOR REFERENCE ONLY. Harness supplied separately

NOTE: FOR REFERENCE ONLY.
Geotab GO Device supplied separately and installed in vehicle

* NOTE: Sensors are not paired with receiver. See separate installation manual for pairing procedure.

A Clarience Technologies Company.

T019-02 Rev 08-25

TireView Receiver, Harness and Repeater Installation
Truck/Tractor Applications

TireView Repeater Installation Procedures
The TireView repeater will boost the signal from the sensors to the TireView unit.
CAUTION The repeater must be installed to help ensure proper operation of the TireView system. Failure to install the repeater could void warranty.
1. The TireView repeater MUST be mounted on the tractor/truck or trailer in the recommended location. The unit is waterproof and can be mounted inside or outside. See Figure 1.
2. Test fit repeater and make sure harness reaches the power source, typically the battery box or battery access area.
3. Connect the 12V+(Red) and 12V-(Black) wires with ring terminals from the repeater to the battery terminals. See Figure 2.
NOTE: When the Repeater receives power, the red light on the Repeater will illuminate (constant or blinking). No additional setup is needed for the repeater.

FRONT

= TireView Repeater
Figure 1: Example repeater location.

4. Route harness for power source to repeater location and secure using zip ties. See Figure 3 .

Figure 2: Example battery box location passenger side floor.
EXAMPLE SHOWS HARNESS EXITING BATTERY BOX AND RUNNING TO REAR OF VEHICLE

5. Secure the Repeater and any extra harness to the tractor/truck/trailer using zip ties, screws or rivets. See Figure 4.

Figure 3: Route repeater harness and secure.
EXAMPLE SHOWS REPEATER SECURED TO FRAME RAIL IN FRONT OF REAR SUSPENSION

Figure 4: Secure repeater and harness.
4

T019-02 Rev 08-25

TireView Receiver, Harness and Repeater Installation
Truck/Tractor Applications

TireView Receiver Installation Procedures
1. Locate Geotab GO Device. Location will vary depending on type of vehicle. These are typically installed in the dash or other access panel areas. See Figure 5.

DASH ACCESS PANEL EXAMPLE

UNDER DASH EXAMPLE

2. Release the Geotab GO Device from any zip ties or securing methods to enable access to ports and ID label. See Figure 6.

Figure 5: Example Geotab GO Device location.

3. Install Geotab IOX RS232F Harness into GO Device using the mini-USB port. See Figure 7.
NOTE: If there is an existing device plugged into the mini-USB port, you must remove it, plug in the IOXRS232F cable, remove the protective cap in the IOXRS232F cable connector and then connect the original accessory to the new IOX-RS232F cable, securing all connections with zip ties.

Figure 6: Geotab GO Device accessed for ports and ID label.
Mini-USB Port

USB Protective
Cap

Figure 7: Insert IOX harness mini-USB into GO Device.

T019-02 Rev 08-25

TireView Receiver, Harness and Repeater Installation
Truck/Tractor Applications
4. Connect TireView Amp to DB9 Harness to the IOX RS232F Harness using the DB9 connectors. See Figure 8.

5. Plug the Amp Connector on the TireView Amp to DB9 Harness into the TireView Receiver. See Figure 9.

Figure 8: Connect DB9 connector to IOX harness.

6. Splice the 12V+(Red) and 12V-(Black) wires together on both harnesses using WAGO push-to-connect. See Figure 10.

NOTE: Depending on harness, you may need to trim and strip wires for connection.

CAUTION Use one WAGO connector for 12V+(Red) and a separate WAGO connector for 12V-(Black). See diagram below.

CORRECT 12V+(Red)

CORRECT 12V-(Black)

INCORRECT

Figure 9: Connect Amp connector into TireView Receiver.

Figure 10: Connect power and ground wires together.

T019-02 Rev 08-25

TireView Receiver, Harness and Repeater Installation
Truck/Tractor Applications
7. Secure any loose cables and components with zip ties as needed and tuck everything into the Geotab GO Device access area. See Figure 11.

For Goodyear TPMS Plus Applications
8. Refer to Goodyear TPMS PLUS “Vehicle Setup and System Programming” manual to capture Geotab GO Device information prior to next step. See Figure 12.

Figure 11: Secure loose cables and components.

9. Proceed with Sensor pairing as outlined in the Goodyear TPMS PLUS “Vehicle Setup and System Programming” manual. See Figure 13.

Figure 12: Refer to Goodyear TPMS PLUS App Installation manual.

Figure 13: Refer to Goodyear TPMS PLUS App Installation manual.

T019-02 Rev 08-25

TireView Receiver, Harness and Repeater Installation
Truck/Tractor Applications

Record of Revisions

Revision Number

Revision Date

April 5, 2024

June 6, 2024

August 20,2025

A Clarience Technologies Company.

T019-02 Rev 08-25

Pressure Systems International 4323 Interstate Way, San Antonio, TX 78219 USA Phone: 210.222.1926, Fax: 210.568.4221

Visit www.psitireinflation.com/resources or scan this QR code for access to the latest revision of this manual.

www.psitireinflation.com/resources#tpms-resources

A Clarience Technologies Company.

T019-02 Rev 08-25

Documents / Resources

P S I T019-02 TireView Receiver [pdf] Installation Guide
T019-02, Rev6, T019-02 TireView Receiver, TireView Receiver, Receiver

References

User Manual

P S I T019-02 TireView Receiver Installation Guide

T019-02 TireView Receiver

Product Specifications

Product Usage Instructions

Receiver, Harness, and Repeater Components

TireView Repeater Installation Procedures

Frequently Asked Questions (FAQ)

Q: Do I need to pair sensors with the receiver?

Documents / Resources

References

Leave a comment

Cancel reply