OrthAlign 407002 Mobile Device Owner’s Manual
Integration Instructions for Host Product Manufacturers
General Specifications
| Host Model Number | 407002 |
| Host Form Factor | Mobile device w/ touchscreen, wireless module, aluminum enclosure. 4.287” x 2.510” x 0.55” |
| Wireless Module | PIXI-9377, WiFi+Bluetooth 5.0(HS) System on Module |
| Wireless Module Form Factor | PIXI 16mm x 12mmx1.0mm Wireless SIP Module |
| Wireless Module MCU | Qualcomm QCA9377-3 |
| WLAN | IEEE 802.11a/b/g/n/ac |
| Bluetooth | Bluetooth 5.0 (BLE) |
| Frequency Range | Bluetooth 5.0: 2402MHz ~ 2480MHz 802.11a: 5180MHz ~ 5240MHz / 5745MHz ~ 5825MHz 802.11n HT20 MHz: 5180MHz ~ 5240MHz / 5745 ~ 5825MHz 802.11n HT40 MHz: 5190MHz ~ 5230MHz / 5755 ~ 5795MHz 802.11ac VHT80 MHz: 5210MHz / 5775MHz |
| Antenna | 1x MHF4 connector, FPC Antenna: Pulse, W3334BD0127 |
| Host Interface | WLAN: SDIO 3.0 BT: UART/ I2S |
| Voltage Input supply for host | I/O: 3.3V |
| Environment Support | Operating Temperature -40~85℃ Storage Temperature -40~135℃ |
Tested Radio Power Levels
| Radio | Band | Transmit Frequency (MHz) | Power Setting | Conducted Output Power | Operational Duty Cycle |
| 802.11 aHT20(6Mbps) | U-NII-1 | 5180 MHz | 11 | 8.5 dBm | 0.6% |
| 5220 MHz | 13 | 10.8 dBm | |||
| 5240 MHz | 14 | 11.4 dBm | |||
| 802.11 aHT20(36Mbps) | U-NII-1 | 5180 MHz | 11 | 8.8 dBm | 0.6% |
| 5220 MHz | 13 | 10.7 dBm | |||
| 5240 MHz | 14 | 12.2 dBm | |||
| 802.11 aHT20(54Mbps) | U-NII-1 | 5180 MHz | 11 | 9.1 dBm | 0.6% |
| 5220 MHz | 13 | 10.7 dBm | |||
| 5240 MHz | 14 | 12.1 dBm | |||
| 802.11 nHT20(MCS0) | U-NII-1 | 5180 MHz | 10 | 7.6 dBm | 0.6% |
| 5220 MHz | 13 | 10.9 dBm | |||
| 5240 MHz | 14 | 11.3 dBm | |||
| 802.11 nHT20(MCS7) | U-NII-1 | 5180 MHz | 10 | 9.1 dBm | 0.6% |
| 5220 MHz | 13 | 10.7 dBm | |||
| 5240 MHz | 14 | 12.8 dBm |
| 802.11 n HT40 (MCS0) | U-NII-1 | 5190 MHz | 11 | 8.8 dBm | 0.5% |
| 5230 MHz | 18 | 15.3 dBm | |||
| 802.11 n HT40 (MCS7) | U-NII-1 | 5190 MHz | 11 | 8.8 dBm | 0.5% |
| 5230 MHz | 18 | 15 dBm | |||
| 802.11 ac VHT80 (MCS0) | U-NII-1 | 5210 MHz | 8 | 5.9 dBm | 0.3% |
| 802.11 ac VHT80 (MCS9) | U-NII-1 | 5210 MHz | 8 | 7.1 dBm | 0.3% |
| 802.11 a HT20(6Mbps) | U-NII-3 | 5745 MHz | 9 | 8.1 dBm | 0.6% |
| 5785 MHz | 11 | 7.7 dBm | |||
| 5825 MHz | 10 | 7.2 dBm | |||
| 802.11 a HT20(36Mbps) | U-NII-3 | 5745 MHz | 9 | 7.7 dBm | 0.6% |
| 5785 MHz | 11 | 9.1 dBm | |||
| 5825 MHz | 10 | 7.4 dBm | |||
| 802.11 a HT20(54Mbps) | U-NII-3 | 5745 MHz | 9 | 8.1 dBm | 0.6% |
| 5785 MHz | 11 | 9.5 dBm | |||
| 5825 MHz | 10 | 8.1 dBm | |||
| 802.11 n HT20 (MCS0) | U-NII-3 | 5745 MHz | 9 | 8 dBm | 0.6% |
| 5785 MHz | 11 | 8.4 dBm | |||
| 5825 MHz | 11 | 9.5 dBm | |||
| 802.11 n HT20 (MCS7) | U-NII-3 | 5745 MHz | 9 | 7.5 dBm | 0.6% |
| 5785 MHz | 11 | 9.4 dBm | |||
| 5825 MHz | 11 | 8.8 dBm | |||
| 802.11 n HT40 (MCS0) | U-NII-3 | 5755 MHz | 10 | 8.3 dBm | 0.5% |
| 5795 MHz | 11 | 8.1 dBm | |||
| 802.11 n HT40 (MCS7) | U-NII-3 | 5755 MHz | 10 | 8.2 dBm | 0.5% |
| 5795 MHz | 11 | 7.6 dBm | |||
| 802.11 ac VHT80 (MCS0) | U-NII-3 | 5775 MHz | 7 | 5.1 dBm | 0.3% |
| 802.11 ac VHT80 (MCS9) | U-NII-3 | 5775 MHz | 7 | 5.8 dBm | 0.3% |
| BLE GFSK1Mbps | BLE | 2402 MHz | 7 | 5.728 dBm | 2.6% |
| BLE GFSK1Mbps | BLE | 2442 MHz | 7 | 5.923 dBm | 2.6% |
| BLE GFSK1Mbps | BLE | 2480 MHz | 7 | 6.03 dBm | 2.6% |
Applicable FCC Rules
FCC Rule ID’s 15.247, 15.407 are applicable to this modular transmitter.
Operational Use Conditions
This device is intended only for OEM integrators under the following conditions:
- The transmitter module may not be co-located with any other transmitter or antenna.
As long as the one condition is met, further transmitter test will not be required.
However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). Any changes or modifications not expressly approved by the manufacturer could void the user’s authority
IMPORTANT NOTE: In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization for this module in combination with the host equipment is no longer considered valid and the FCC ID of the module cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization.
Limited Module Procedures
Not applicable for this device
Trace Antenna Designs
Trace antenna designs are not applicable to this module
RF Exposure Considerations
The product complies with the US portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available.
Host product manufacturers shall provide the following text in the end-product manual:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. The equipment should be installed and operated with a minimum distance of 5 mm between the radiator and your body.
Antennas
This module is only FCC authorized for the following specific antenna. See limited module procedures information for antenna installation instructions.
Number of Antennas: 1
Antenna Part Number: W3334BD0127
Antenna Manufacturer: Pulse
Antenna Gain: 4dBi (2.4Ghz) / 5.5dBi (5GHz)
Max Antenna Gain: 5dBi (2.4Ghz) / 6.5dBi (5GHz)
Antenna Description: FPC, linear polarized
End Product Labeling
The final end product must be labelled in a visible area with the following:
Contains FCC ID: “2AVMS-405061”
Information on test modes and additional testing requirements
Qualcomm QCA-9377 chipset test firmware shall be used to configure the module for test modes. Please see QCA9377_FCC_Certification_User_Guide.pdf for further information.
Additional Testing, Part 15 Subpart B Disclaimer
This module is only FCC authorized for these specific rule parts. The host product manufacturer is responsible for compliance with any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. Final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed.
153 Technology Drive, Suite 100 Irvine CA, 92618
octhalign.com
info@ortnatign.com
Documents / Resources
 |
OrthAlign 407002 Mobile Device [pdf] Owner's Manual 405061, 407002 Mobile Device, 407002, Mobile Device, Device |
