ONNEX WZ-0087 Oxygen Sensor for Changan Oushang
Product Information
General Information
These instructions provide information on protective gloves in accordance with EU Regulation 2016/425. The gloves are designed to protect against mechanical risks.
Specifications
| Testing Criteria | Level |
|---|---|
| Cut Resistance (EN ISO 13997) | A-F |
| Puncture Resistance | 0-4 |
| Tear Resistance | 0-4 |
| Blade Cut Resistance | 0-5 |
| Abrasion Resistance | 0-4 |
Attention
- The performance levels achieved are indicated in the table above. The higher the value, the better the test result. If marked with “X”, the test is not applicable.
- Use gloves only if there is a risk of becoming entangled in moving machine parts. Gloves must not be worn.
Product Using Instructions
Inspection
- Inspect protective gloves for tears and holes before each use. Replace damaged gloves. Only properly fitting gloves guarantee protection.
Cleaning
- Depending on the degree of soiling, knock out, brush out, or wipe with a damp cloth after each use. Allow to dry with good ventilation.
Storage
- Store at normal room temperature, dry and well-ventilated. Avoid sunlight and direct heat.
Disposal
- The article is designed for the lifespan of wear and tear. It is therefore not suitable for recycling or specific disposal.
- Dispose of contaminated protective gloves as hazardous waste. Information on this can be obtained from the relevant waste disposal authorities.
Declaration of Conformity
- The declaration of conformity is available on our website: www.connexprotective.de
FAQ
- What should I do if the gloves are damaged?
- Replace damaged gloves immediately to ensure protection.
- How should I clean the gloves?
- Knock out, brush out, or wipe with a damp cloth after each use. Allow to dry with good ventilation.
- Can the gloves be recycled?
- No, the gloves are not suitable for recycling. Dispose of them as hazardous waste if contaminated.
Instructions for use
Instructions for use for PPE category I protective gloves in accordance with EU Regulation 2016/425
EN ISO 21420:2020 Protective gloves – General requirements and test methods
EN 388:2016+A1:2018 Protective gloves against mechanical risks
ATTENTION
- The performance levels achieved are indicated in this order below the pictogram.
- Protection level „O” means that the glove has not reached performance level „1″.
- The higher the value, the better the test result. Level X stands for „not tested” or „not applicable”.
- The test results refer to the reinforced/coated part of the gloves.
- With a tear propagation force of 1 or higher: If there is a risk of becoming entangled in moving machine parts, gloves must not be worn.
Testing criteria
Cleaning And Disposal
Inspection
- Inspect protective gloves for tears and holes before each use. Replace damaged gloves. Only properly fitting gloves guarantee protection and grip.
Cleaning
- Depending on the degree of soiling, knock out, brush out or wipe with a damp cloth after each use. Allow to dry with good ventilation.
Storage
- Store at normal room temperature, dry and well ventilated. Avoid sunlight and direct heat radiation.
Durability
The service life depends on the degree of wear and the intensity of use in the respective areas of application. It is therefore not possible to specify a specific period.
Manufacturing period
Best before date
PO: XXXXXXXXXX
Disposal
- The gloves should be disposed of with household waste if handled properly. Contaminated protective gloves, that may pose a hazard must be disposed of properly.
- Information on this can be obtained from the relevant waste disposal organisation.
Available sizes
Declaration
- The declaration of conformity will be shown on website: www.conmetallmeister.de
More Information
CE
СТС
- Parc Sc. T. Garn. – 4, rue Herm. Frenkel 69367 Lyon Cedex 07
- Country: France
- Notified Body number: 0075
Hergestellt für:
- Conmetall Meister GmbH
- Hafenstraße 26 29223 Celle • GERMANY
- cm@comei.info
Documents / Resources
 |
ONNEX WZ-0087 Oxygen Sensor for Changan Oushang [pdf] Instructions WZ-0087 Oxygen Sensor for Changan Oushang, WZ-0087, Oxygen Sensor for Changan Oushang, Sensor for Changan Oushang, Changan Oushang, Oushang |
