OMCONNECT K12 Smart Keybox Security KeySafe
What’s Included
Specification
- Model K12
- Unlock Mechanism Bluetooth, PIN Code, App
- Battery 4 x AAA Alkaline Battery(Not included in the package)
- Material Body Zinc Alloy, SUS304
- Jump Start USB-C
Features
Lock&Unlock
- Administrator Unlock
Set a Master Administrator PIN for Unlocking, settings, operations etc. and only the administrator could change the administrator PIN code. - Anti-peeping
Add up to 10 digits before and after PIN code to intensify your PINs.
Mobile Control
- Bluetooth one-touch unlock
With your Mobile you could unlock the KeyBox by tapping the ” ” on the App - Mobile Administrator
Set Administrator PIN Codes from your Mobile to unlock, add users, delete users, etc. - User Unlock
This KeyBox allows to add up to 100 user PIN codes for your family, friends and visitors. - Offline Unlock
You could generate offline code through mobile App, for scheduled access, parcel delivery, housekeeping, etc.
Battery
- Battery Life
4 AAA batteries, the life cycle will be more than 12 months, please use good batteries. - Low Consumption
BLE broadcasting turns to sleep mode if no operations. - Low Battery
When the battery runs out of power, system will remind you to replace the batteries.
Emergency
- Jump Start
When the power is down and use USB-C to jump start the lock and get it unlocked - System Lockdown
The lock will be lockdown for 5 minutes if continuously enter wrong PINs for 5 times.
Quick Start
Step 1>Install Battery >. Remove the battery cover
- Insert 4 x AAA batteries into the battery dock.
Step 2>Download Mobile App
- Scan QR Code below and download the App and turn on your mobile Bluetooth
Step 3>Add Device
- Go to App Home page, click Add Device or click “+” on the upper right.
- Press the “Reset” button and hold it for 3 beeps to start pairing
- You will see the detected device and click “Go to add”.
- Connecting, you need to wait for few seconds to let it finish.
- Device added
Step 4>Change Admin Password-Initial Admin Password:123456
- Press and hold for 3 beeps
- Right after the 3 beeps please key in:
Initial Admin Password + + new admin password+ +new admin password+
Mechanical Instructions
Password & Factory Mode:
- Password Length
Password must be 6 digits (no more no less) - Add User Password
Click + 0 + until the blue light blinks
> Enter admin password +
> Enter new user password +
> Enter new user password again and press
> When the (Enter button) blinks in green, user password has been set. - Delete User Password
Click + 2 + until the blue light blinks
> Enter admin password and do not press any other button
> Enter the user password you wish to delete and press
> When the (Enter button) blinks in green, the password has been deleted. - Delete All User Password
Click + 00000 + until the blue light blinks
> Enter admin password and press
> When the (Enter button) blinks in green, all passwords have been deleted. - Virtual digits-Anti-Spy
Add any digits before and after the correct password the KeyBox unlocks as always. - System Lockdown
KeyBox will Lockdown for 5 minutes if entering wrong password continuously 5 times. - Reset Factory Mode
Press and hold the reset button for 5 seconds and with a long beep.
Bluetooth broadcasting & re-connecting:
- Press and hold the reset button for 3 beeps, you will be able to pair the device.
- Bluetooth broadcasting will turn to sleep mode if no operations within 1 minute.
- Press any key to activate the Bluetooth, App&Device will get reconnected each other.
App Instructions
- You will see all devices and rooms on the home page.
- Tap the Device to start operating.
- Tap “Me” at the bottom to manage your home.
- Touch the lock sign to unlock and lock.
- Tap “Bell” sign to check the alarm records.
- Tap “Member Management to add or delete members.
- Tap “opening record” to check opening logs.
- Tap “Intelligent Linkage” to turn on and off go home mode.
- Tap “Set” to manage passwords
- Tap “Get dynamic code” to get a code.
- Tap “copy code” and send it to friend or family.
- Tap “Pen” sign to edit your personal information.
- Go to “Members” to add family or other members
- Tap “+” to add family member or other members
- Tap “ Add it now” under Family to add family members.
- Owner need to complete the Home information before adding any family member if required
- The member need to be registered to the App before adding as a family member
- Fill up member information and set the role of the member
- Tap “Save” to complete and the member will be able to operate the device on his App
- Go to “Opening Logs” to check the unlocking history
- With this feture you will be able to find out when and who unlocked the KeyBox
- Go to “Intelligent Linkage” to set more smart functions
- Tap the green bar to turn on “Family go home”function.
- Tap the orange bar to turn on “Door lock alarm”function
- You will get notification if user unlocked with Bluetooth
- Go to “me” homepage and got to message center to check the records.
- Tap “Member” to add or remove codes.
- Tap “Temporary Code” to manage online and offline codes.
- set an online one time code.
- Tap “periodic Code” under Online Code to set a online code which will be available in a period of time.
- one time offline code which will be a 10 digits code and use it when the device is offline. one time offline code which will be a 10 digits code and use it when the device is offline.
- Tap “Offline Temporary Code” under Offline Code t generate an offline code (10 digits) which will be available in a period of time, and use when the device is offline or Bluetooth disconnected with device.
- Please note if the code less than 10 digits you need to regenerate a new code, the code must be 10 digits.
Documents / Resources
 |
OMCONNECT K12 Smart Keybox Security KeySafe [pdf] User Manual K12 Smart Keybox Security KeySafe, K12, Smart Keybox Security KeySafe, Keybox Security KeySafe, Security KeySafe, KeySafe |
