Ceiling Mount Access Point
“
Specifications
- Product: Omada Ceiling Mount Access Point
- Model: EAP
- Environment: Suitable for various scenarios
- LED Indicators: System status indication
- Power Supply: Normal and Low power supply indicators
- Software Compatibility: Omada Controller
Hardware Overview
Ceiling Mount Access Point
The EAP is designed for different environments and comes with a
system LED on the front panel to indicate system status.
Front Panel
The front panel of the EAP features an LED that provides various
indications:
- LED Status: Indication
- On – Working normally/Initializing.
- Blue – Normal power supply.
- Yellow – Low power supply.
- Off – Working abnormally/Power off/LED is turned off.
- Flashes twice – Initialization is complete.
- Flashing quickly – The EAP is resetting, or the Omada
controller is locating the device. - Flashing once per second – The EAP is updating the
firmware. - On with periodic off – The EAP is in the isolated state.
Product Usage Instructions
Hardware Installation
Ceiling Mount Access Point
- Choose an appropriate location on the ceiling to mount the
access point. - Securely attach the access point using the provided mounting
hardware. - Connect the necessary cables to the access point based on your
network setup.
Software Configuration
To configure the EAP:
- Access the Omada Controller interface either through a web
browser or the dedicated software. - Follow the on-screen instructions to set up the EAP, including
network settings and security configurations. - Ensure the EAP is connected to the network properly for the
configurations to take effect.
FAQ
Q: Where can I find additional documentation for the EAP?
A: You can find more resources, including user guides and
technical support, on the Omada Networks support page at
https://support.omadanetworks.com/.
“`
EAP Start Guide
© 2025 TP-Link 1900000354 REV1.0.0
CONTENTS
About This Guide………………………………………………………………………………………………….01
Related Documentation ……………………………………………………………………………………………………………………01 More Resources ………………………………………………………………………………………………………………………………..01
Hardware Overview……………………………………………………………………………………………..02
Ceiling Mount Access Point …………………………………………………………………………………………………………….02 Front Panel…………………………………………………………………………………………………………………………………… 02 Rear Panel ……………………………………………………………………………………………………………………………………. 03
Hardware Installation…………………………………………………………………………………………..05
Ceiling Mount Access Point …………………………………………………………………………………………………………….05
Software Configuration ………………………………………………………………………………………06
Get Started …………………………………………………………………………………………………………………………………………06 Omada App …………………………………………………………………………………………………………………………………………07 More Configurations …………………………………………………………………………………………………………………………07
About This Guide
Omada offers scenario-based access points (hereinafter referred to as EAPs) for different kinds of environments. This document offers startup guidance for an EAP, including a detailed hardware overview and quick references for hardware installation and software configuration.
Related Documentation
The Quick Installation Guide can be found in the product packaging and on the Product Support page: https://support.omadanetworks.com/product/
The latest Regulatory Compliance document, Omada Access Point User Guide, and Omada Controller User Guide can be found on the Documents page: https://support.omadanetworks.com/ document/
More Resources
Main Site Video Center Documents Product Support Technical Support
https://www.omadanetworks.com/ https://support.omadanetworks.com/video/ https://support.omadanetworks.com/document/ https://support.omadanetworks.com/product/ https://support.omadanetworks.com/contact-support/
For technical support, the latest software, and management app, visit https://support. omadanetworks.com/.
01
Hardware Overview
This chapter provides a detailed hardware overview of the EAP.
Ceiling Mount Access Point
Front Panel
The EAP is equipped with a system LED that indicates the system status on the front panel.
LED
LED Status
Indication
On
· For EAPs with single-color LED:
Working normally/Initializing.
· For EAPs with dual-color LED:
Blue: Normal power supply
Yellow: Low power supply
Off
Working abnormally/Power off/LED is turned off.
Flashes twice
Initialization is complete.
Flashing quickly
The EAP is resetting, or the Omada controller is locating the device.*
Flashing once per second
The EAP is updating the firmware.
On with periodic off
The EAP is in the isolated state.
* When the Locate feature is activated in the Omada Controller, the LED will flash quickly for 10 minutes to help you locate and identify the device. You can disable this feature manually to stop the device from flashing.
02
Rear Panel
The ports, buttons, and other parts are located on the rear panel and may vary by model.
Bracket Aligning Mark
Bracket Aligning Mark
RESET
Cable Compartment Cover
L-Key Slot Bracket Aligning Mark
RESET
Cable Compartment Cover
Removable Block Bracket Aligning Mark
Note: For an AP with a Cable Compartment Cover, to avoid device damage, do not insert any objects into the holes for attaching the cover!
Item
Description
RESET Button
With the device powered on, use a pin to press and hold this button for about 5 seconds until the LED flashes quickly. Then, release the button. The device will restore to its factory default settings.
Ethernet Port (PoE IN)
Connect to a gateway/router or a switch to transmit data or to a PSE (Power Sourcing Equipment), such as a PoE switch, for both data transmission and Power over Ethernet (PoE) via Ethernet cable.
Ethernet Port
(Only for certain models) Connect to a wired device.
Power Port
Connect to a standard electrical wall outlet via a power adapter to power the EAP.
Bracket Aligning Mark
Align the triangle mark to the U gap on the provided mounting bracket, then rotate the AP clockwise to attach it.
L-Key Slot
(Only for certain models)
Insert the provided L-Key into the slot , then rotate the AP counterclockwise to unlock it from the mounting bracket.
Cable Compartment Cover
(Only for certain models) Slide the cover to the AP’s rear panel for cable concealment.
03
Removable Block
(Only for certain models) Remove the block to route a cable if needed.
Note: For EAPs with a 10 Gbps port, using a CAT5e cable limits the Ethernet port’s 10 Gbps link to less than 55 meters. To achieve longer transmission distances, use a shielded CAT6A cable.
04
Hardware Installation
Omada offers scenario-based EAPs for different kinds of environments. This chapter provides quick references for hardware installation.
Ceiling Mount Access Point
The Ceiling Mount Access Point can be mounted to a ceiling, wall, or junction box. You can follow the Quick Installation Guide to install the EAP using the accessories in the product packaging. The Quick Installation Guide can be found in the product packaging and on the Support page of your model at https://www.omadanetworks.com/business-networking/omada-wifi-ceiling-mount/.
05
Software Configuration
Omada EAPs offer wireless coverage solutions for small to medium-sized businesses and households. They can work independently as standalone APs or be centrally managed via an Omada Controller, delivering a flexible, feature-rich, and easy-to-configure wireless network.
Get Started
Choose a method to set up your EAPs: · Method 1: Standalone Mode Configure and manage each EAP on its standalone page. Note: The figure below uses the Ceiling Mount Access Point for demonstration. Other types of EAPs can be used in a similar manner.
Gateway/Router Switch
EAP
EAP
For instructions on how to get started with a standalone EAP, refer to https://www.omadanetworks. com/support/faq/4097/. · Method 2: Controller Mode Configure and manage EAPs (and other Omada devices) centrally with an Omada Controller. Note: The figure below uses a Ceiling Mount Access Point for demonstration. Other types of EAPs can be
06
used in a similar manner.
Gateway/Router Switch
Omada Central (Cloud-Based)
Or
Controller
On-Premises Controller
EAP
EAP
EAP
For instructions on how to get started with an Omada Controller, refer to https://www. omadanetworks.com/support/faq/4096/.
Omada App
With the TP-Link Omada app, you can access and manage your Omada devices at a local site or remotely with a tap of your phone.
or
Scan for Omada App
Omada App
More Configurations
For more configurations, refer to the User Guides of the Controller and EAPs on the Documents page: https://support.omadanetworks.com/document/
07
Documents / Resources
 |
Omada Ceiling Mount Access Point [pdf] User Guide EAP-Start-Guide-BR JP, Ceiling Mount Access Point, Mount Access Point, Access Point |