O2066PM
Wi-Fi Tri-band 2×2 MIMO DBS
802.11ax + Bluetooth 5.2 Module
www.ofeixin.com
OFEIXIN TECHNOLOGY LIMITED
O2066PM DATESHEET
Cover of Approval Sheet
| PRODUCT NAME | Part No. | Description |
| O2066PM | FWAAO2066PM10 | QCA2066 M.2 3.3V 2T2R 22*30* 2.7mm DBS
11ax BT5.2-UART External 3antenna Shield CAN |
| FWAAO2066PM20 | QCA2066 M.2 3.3V 2T2R 22*30* 2.7mm DBS
11ax BT5.2-USB External 3antenna Shield CAN |
Customer:……………………..
Customer P/N:………………………….
Signature:………………
Date:…………………………
Maker Information:
OFEIXIN TECHNOLOGY LIMITED
Room 503, Building A3, Area B, Songbai Industrial Park, Minghuan East Road, Shangcun Community, Gongming Street, Guangming District, Shenzhen
Revision History
| Version | Date | Description | Draft | Approved |
| V1.0 | 2022-04-06 | -Preliminary Project version | CCJ | Turbo |
| V1.1 | 2022-06-30 | -append current description | CCJ | Turbo |
| V1.2 | 2022-08-10 | -Addition the description | CCJ | Turbo |
Overview
1.1 Introduction
The O2066PM1 device is a highly integrated module supporting 802.11ax Wi-Fi and Bluetooth (BT) Milan. The O2066PM1 device supporting simultaneous operation on 2.4 GHz and 5 GHz, or 6 GHz, also known as Dual Band Simultaneous (DBS).
The wireless module complies with IEEE 802.11 a/b/g/n/ac/ax 2×2 MIMO standard and it can achieve up to a speed of 2975.6Mbps (5/6G 2×2 160MHz 11ax +2.4G 2×2 40MHz 11ax DBS). The integrated module provides PCIe interface for Wi-Fi, UART/PCM or USB interface for Bluetooth.
1.2 Features
- Supports 2×2 Multi-User Multiple-Input Multiple-Output (MU-MIMO).
- Dual Band Simultaneous (DBS), up to 3 Gbps data rate (5/6G 2×2 160MHz 11ax +2.4G 2×2 40MHz 11ax DBS).
- Tri-band 2.4 GHz/5 GHz/6 GHz support.
- 20MHz/40MHz channel bandwidth for 2.4 GHz and 20MHz/40MHz/80MHz/160 MHz channel bandwidth for 5 GHz/6 GHz.
- Seamless antenna sharing with Bluetooth, LTE, LTE-U, and 5G.
- Dynamic Frequency Selection
- Offloading traffic for minimal host utilization at 802.11ac/ ax speeds.
- Low-power PCIe (with L1 substate) interface.
- Integrated close-loop power detector.
- Supports 2 Mbps Bluetooth Low Energy (BLE), BLE Long Range.
- Split ACL support for A2DP true stereo (earbuds) .
- Dedicated Bluetooth antenna, and concurrent with 5G WLAN.
- Dual eSCO and dual A2DP streams.
- Backward-compatible with previous Bluetooth standards.
- Standard M.2 2230 Key E Golden Finger interface.
1.3 Block Diagram 
1.4 General Specification
| Model Name | O2066PM |
| Product Description | Support WiFi6E+BT5.2 |
| Dimension | L x W x H: 22 x 30 x 2.7 (typical) mm |
| Wi-Fi Interface | M.2 2230 Key E |
| BT Interface | UART/PCM or USB |
| Operting temperature | -30°C to 85°C* |
| Storage temperature | -40°C to 125°C |
Note: The maximum ambient temperature of 802.11ax 160M MCS11 for long-term stable operation is less than or equal to 82°C.
1.5 Recommended Operating Rating
| Feature | Minimum | Type | Maximum | Units | |
| Operating Temperature | -30 | 25 | 85 | °C | |
| VCC | 3.20 | 3.3 | 3.45 | V | |
|
Power Consumption (Type VCC) |
TX (2.4G HE40) | 441 mA | |||
| RX (2.4G HE40) | 147 mA | ||||
| TX (5G HE160) | 554 mA | ||||
| RX (5G HE160) | 211 mA | ||||
| Power Up | 118 mA | ||||
| BT TX（1M@7dBm） | 147 mA | ||||
| BT RX | 136 mA | ||||
Note: Use QRCT tool, TX mode:EnablingContinuousModulatedTX;Duty Cycle:50%;TX Power
Control:AutoPower, test the maximum current of the module 3.3V power supply when NSS=1.
RF Specification
2.1 Wi-Fi RF Specification
| 2.4GHz RF Specification | ||||
| Feature | Description | |||
| Operating Frequency | 2.400～2.4835GHz | |||
| Standards | Wi-Fi: IEEE 802.11b/g/n/ac/ax & Wi-Fi compliant | |||
| Operating Channel | 2.4GHz : Ch1~14 | |||
| Modulation | 802.11b : CCK 802.11 g/n/ac/ax : OFDM /1024-QAM、256-QAM、64-QAM、16-QAM、QPSK、BPSK | |||
| PHY Data rates | Wi-Fi:802.11b:11,5.5,2,1Mbps 802.11g:54,48,36,24,18,12,9,6Mbps 802.11n: up to 300Mbps | |||
| 802.11ac: up to 400Mbps
802.11ax:up to 3 Gbps data rate (2.4G 2×2+5G or 6G 2×2 11ax DBS) |
||||
| Output Power, tolerance ± 1.5 dB | ||||
| Protocol Standard | Data Rate | Spec.(dBm) | EVM(dBm) | |
| 802.11b | @11Mbps | 16 | ≦-9 | |
| 802.11g | @54Mbps | 16 | ≦-25 | |
| 802.11n | @HT40 MCS 7 | 16 | ≦-28 | |
| 802.11ac | @vHT40 MCS 9 | 14.5 | ≦-32 | |
| 802.11ax | @HE40 MCS 11 | 12.5 | ≦-35 | |
| Receiver Sensitivity, CCK modulation PER≦8%、OFDM modulation PER≦10% | ||||
| Protocol Standard | Data Rate | Spec.(dBm) | ||
|
802.11b(20MHz) |
1Mbps | -82 | ||
| 11Mbps | -76 | |||
|
802.11g(20MHz) |
6Mbps | -82 | ||
| 54Mbps | -64 | |||
|
802.11n(20MHz) |
MCS 0 NSS1 | -82 | ||
| MCS 7 NSS1 | -64 | |||
|
802.11n(40MHz) |
MCS 0 NSS1 | -79 | ||
| MCS 7 NSS1 | -61 | |||
|
802.11ac(20MHz) |
MCS 0 NSS1 | -82 | ||
| MCS 9 NSS1 | -59 | |||
|
802.11ac(40MHz) |
MCS 0 NSS1 | -79 | ||
| MCS 9 NSS1 | -57 | |||
| 802.11ax(20MHz) | MCS 0 NSS1 | -82 | ||
| MCS 11 NSS1 | -52 | ||
|
802.11ax(40MHz) |
MCS 0 NSS1 | -79 | |
| MCS 11 NSS1 | -49 | ||
| 5GHz RF Specification | |||
| Feature | Description | ||
| Operating Frequency | 5G:5.15 GHz ~ 5.845 GHz (5.0 GHz ISM Band) | ||
| Standards | Wi-Fi: IEEE 802.11 a/n/ac/ax 2×2, Wi-Fi compliant | ||
|
Modulation |
802.11 a/n/ac/ax : OFDM /1024-QAM、256-QAM、64-QAM、16-QAM、QPSK、BPSK | ||
|
PHY Data rates |
Wi-Fi: 802.11a:54,48,36,24,18,12,9,6Mbps 802.11n: up to 300Mbps 802.11ac: up to 800Mbps（5G 2×2 VHT80）
802.11ax:up to 3 Gbps data rate (2.4G 2×2+5G 2×2 11ax DBS) |
||
| Output Power, tolerance ± 1.5 dB | |||
| Protocol Standard | Data Rate | Spec.(dBm) | EVM(dBm) |
| 802.11a | @54Mbps | 16.5 | ≦-25 |
| 802.11n | @HT40 MCS 7 | 16 | ≦-28 |
| 802.11ac | @vHT80 MCS 9 | 13.5 | ≦-32 |
| 802.11ax | @HE160 MCS 11 | 11.5 | ≦-35 |
| Receiver Sensitivity,OFDM modulation PER≦10% | |||
| Protocol Standard | Data Rate | Spec.(dBm) | |
|
802.11a(20MHz) |
6Mbps | -82 | |
| 54Mbps | -64 | ||
|
802.11n(20MHz) |
MCS 0 NSS1 | -82 | |
| MCS 7 NSS1 | -64 | ||
|
802.11n(40MHz) |
MCS 0 NSS1 | -79 |
| MCS 7 NSS1 | -64 | |
|
802.11ac(20MHz) |
MCS 0 NSS1 | -82 |
| MCS 9 NSS1 | -57 | |
|
802.11ac(40MHz) |
MCS 0 NSS1 | -79 |
| MCS 9 NSS1 | -54 | |
|
802.11ac(80MHz) |
MCS 0 NSS1 | -76 |
| MCS 9 NSS1 | -51 | |
|
802.11ax(20MHz) |
MCS 0 NSS1 | -82 |
| MCS 11 NSS1 | -52 | |
|
802.11ax(40MHz) |
MCS 0 NSS1 | -79 |
| MCS 11 NSS1 | -49 | |
|
802.11ax(80MHz) |
MCS 0 NSS1 | -76 |
| MCS 11 NSS1 | -46 | |
|
802.11ax(160MHz) |
MCS 0 NSS1 | -73 |
| MCS 11 NSS1 | -43 | |
| 6GHz RF Specification | ||
| Feature | Description | |
| Operating Frequency | 6G: 5.925 GHz ~ 7.125 GHz | |
| Standards | Wi-Fi: IEEE 802.11 a/n/ac/ax 2×2, Wi-Fi compliant | |
|
Modulation |
802.11 a/n/ac/ax : OFDM /1024-QAM、256-QAM、64-QAM、16-QAM、QPSK、BPSK | |
|
PHY Data rates |
Wi-Fi: OFDM:54,48,36,24,18,12,9,6Mbps
802.11ax:up to 3 Gbps data rate (2.4G 2×2+6G 2×2 11ax DBS) |
|
| Output Power, tolerance ± 1.5 dB | ||
| Protocol Standard | Data Rate | Spec.(dBm) | EVM(dBm) |
| 802.11a | @54Mbps | 13.5 | ≦-25 |
| 802.11n | @HT40 MCS 7 | 13.5 | ≦-28 |
| 802.11ac | @vHT80 MCS 9 | 13 | ≦-32 |
| 802.11ax | @HE160 MCS 11 | 10.5 | ≦-35 |
| Receiver Sensitivity,OFDM modulation PER≦10% | |||
| Protocol Standard | Data Rate | Spec.(dBm) | |
|
802.11a(20MHz) |
6Mbps | -82 | |
| 54Mbps | -64 | ||
|
802.11ax(20MHz) |
MCS 0 NSS1 | -82 | |
| MCS 11 NSS1 | -52 | ||
|
802.11ax(40MHz) |
MCS 0 NSS1 | -79 | |
| MCS 11 NSS1 | -49 | ||
|
802.11ax(80MHz) |
MCS 0 NSS1 | -76 | |
| MCS 11 NSS1 | -46 | ||
|
802.11ax(160MHz) |
MCS 0 NSS1 | -73 | |
| MCS 11 NSS1 | -43 | ||
2.2 BT RF Specification
| Feature | Description | ||
| Operating Frequency | 2.402～2.480GHz | ||
| Number of Channels | 79 channels | ||
| Standards | Bluetooth V5.2 | ||
| Modulation | 8DPSK, π/4 DQPSK, GFSK | ||
| PHY Data rates | Supports 2Mbps Bluetooth Low Energy(BLE),BLELong Range | ||
| Output Power | Min(dBm) | Typical(dBm) | Max(dBm) |
| 7 | 10 | ||
| Sensitivity @ BER=0.1% for GFSK (1Mbps) |
-92 |
||
| Sensitivity @ BER=0.01% for π/4-DQPSK (2Mbps) |
-92 |
||
| Sensitivity @ BER=0.01% for 8DPSK (3Mbps) |
-85 |
||
Pin Assignments
3.1 Pin Outline
3.2 Pin Definition
Top side
| NO | Name | Type | Description | Voltage | |
| 1 | GND1 | – | Ground | ||
| 3 | BT USB D+ | I/O | The usb1.1 interface is only valid for BT USB modules | ||
| 5 | BT USB D1 | I/O | The usb1.1 interface is only valid for BT USB modules | ||
| 7 | GND2 | – | Ground | ||
| 9 | NC | – | |||
| 11 | NC | – | |||
| 13 | NC | – | |||
| 15 | NC | – | |||
| 17 | NC | – | |||
| 19 | NC | – | |||
| 21 | NC | – | |||
| 23 | NC | – | |||
| 33 | GND3 | – | Ground | ||
| 35 | PERP0 | I | PCIe RX differential signals | ||
| 37 | PERN0 | I | |||
| 39 | GND4 | – | Ground | ||
| 41 | PETP0 | O |
PCIe TX differential signals |
||
| 43 | PETN0 | O | |||
| 45 | GND5 | – | Ground | ||
| 47 | REFCLKP0 | I |
PCIe clock differential input signal |
||
| 49 | REFCLKN0 | I | |||
| 51 | GND6 | Ground | |||
| 53 | CLKREQ0#(I/O)(0/3.3V) ① | I/O | PCIe reference clock request signal, open drain,active low | 3.3V | |
| 55 | PEWAKE0#(I/O)(0/3.3V) ① | I/O | PCIe wake up host, open drain, active low |
3.3V |
|
| 57 | GND7 | – | Ground | ||
| 59 | RESERVED_PERP1 | – | NC | ||
| 61 | RESERVED_PERN1 | – | NC | ||
| 63 | GND8 | – | Ground | ||
| 65 | RESERVED_PETP1 | – | NC | ||
| 67 | RESERVED_PETN1 | – | NC | ||
| 69 | GND9 | – | Ground | ||
| 71 | RESERVED_REFCLKP1 | – | NC | ||
| 73 | RESERVED_REFCLKN1 | – | NC | ||
| 75 | GND9 | – | Ground | ||
Bottom side
| NO | Name | Type | Description | Voltage | |
| 2 | 3_3V_1 | P | Power supply | 3.3V | |
| 4 | 3_3V_2 | P | Power supply | 3.3V | |
| 6 | NC | – | RESERVED | ||
| 8 | PCM_CLK | I/O | BT PCM clock （ Only valid for UART modules） | 1.8V | |
| 10 | PCM_SYNC | I/O | BT PCM sync （ Only valid for UART modules） | 1.8V | |
| 12 | PCM_OUT | O | BT PCM data out（Only valid for | 1.8V | |
| UART modules） | |||||
| 14 | PCM_IN | I | BT PCM data in（Only valid for UART modules） | 1.8V | |
| 16 | NC | – | RESERVED | ||
| 18 | GND11 | – | Ground | ||
| 20 | UART_WAKE_N ① | O | BT wake up host signal （ Only valid for UART modules） | 3.3V | |
| 22 | UART_TXD(O)(0/1.8V) | O | BT UART interface（Only valid for UART modules） | 1.8V | |
| 32 | UART_RXD(I)(0/1.8V) | I | 1.8V | ||
| 34 | UART_RTS(O)(0/1.8V) | O | BT UART request to send（Only valid for UART modules） | 1.8V | |
| 36 | UART_CTS(I)(0/1.8V) | I | BT UART clear to send （ Only valid for UART modules） | 1.8V | |
| 38 | NC | – | |||
| 40 | NC | – | |||
| 42 | NC | – | |||
| 44 | WAKE_BT ① | I | Host wake up BT signal | 3.3V | |
| 46 | LTE_COEX_TXD | O | RESERVED/LTE coexistence UART TXD | 1.8V | |
| 48 | LTE_COEX_RXD | I | RESERVED/LTE coexistence UART RXD | 1.8V | |
| 50 | SUSCLK_32KHZ ① | I | Sleep clock input | 3.3V | |
| 52 | PERST0#(I)(0/3.3V) ① | I | PCIe reset module,internal weak pull down | 3.3V | |
| 54 | NC | – | RESERVED | ||
| 56 | NC | – | RESERVED | ||
| 58 | NC | – | RESERVED | ||
| 60 | NC | – | RESERVED | ||
| 62 | NC | – | |||
| 64 | NC | – | |||
| 66 | NC | – | |||
| 68 | NC | – | |||
| 70 | NC | ||||
| 72 | 3_3V_3 | P | Power supply | 3.3V | |
| 74 | 3_3V_4 | P | Power supply | 3.3V | |
Note：The I/O level of the pin marked ① is 3.3V, and the other I/O level is 1.8V。
Dimensions
4.1 Physical Dimensions and Module Photo
(Unit: mm) 
4.2 Module Physical Dimensions
(Unit: mm) 
Reference Design
5.1 Reference schematic 
Note：
a）C247, C251 should be closed to host.
b)The power supply “3.3V_IN” switching noise is less than 100mV and the ripple is less than 30 mV.
c） PCIe differential signals should be followed 100 Ohm impedance.
d） For the I/O interface voltage, please refer to chapter 5 pin definition.
e） For the 1.8V interface, such as PCM, UART and some I/O, if the host voltage level is 3.3V or 5V, need to add level shift circuit.
5.2 External Antenna
When the customer selects an external antenna, the external antenna selected must meet the parameter requirements specified ,Impedance 50Ω
5.3 Real-world Testing
| 2.4G Real-world Testing | |||||||
|
Protocol Standard |
channel |
Power (dBm) |
EVM(dB) |
Rx Sensitivity (dBm) | |||
|
802.11g(54Mps) |
ANT0 |
2412 | 15.7 | -35.3 | -72 | ||
| 2437 | 15.9 | -35.5 | -73 | ||||
| 2472 | 16.1 | -35.1 | -73 | ||||
|
ANT1 |
2412 | 16.2 | -34.2 | -73 | |||
| 2437 | 16.1 | -35.7 | -73 | ||||
| 2472 | 16.4 | -34.2 | -73 | ||||
|
802.11ax(HE20_MCS11) |
ANT0 |
2412 | 13.6 | -38.9 | -58 | ||
| 2437 | 13.3 | -39 | -58 | ||||
| 2472 | 13.8 | -39.2 | -58 | ||||
|
ANT1 |
2412 | 13.9 | -37.5 | -58 | |||
| 2437 | 14.2 | -38.7 | -58 | ||||
| 2472 | 13.7 | -36.3 | -58 | ||||
|
802.11ax(HE40_MCS11) |
ANT0 |
2422 | 12.9 | -37.2 | -55 | ||
| 2462 | 12.8 | -37.9 | -55 | ||||
|
ANT1 |
2422 | 13.2 | -37.2 | -55 | |||
| 2462 | 13.1 | -38.9 | -55 | ||||
| 5G Real-world Testing | |||||||
|
Protocol Standard |
channel |
Power (dBm) |
EVM(dB) |
Rx Sensitivity (dBm) | |||
|
802.11a(54Mps) |
ANT0 |
5180 | 16.9 | -33.6 | -73 | ||
| 5500 | 16.8 | -32.9 | -73 | ||||
| 5825 | 16.6 | -33.2 | -73 | ||||
|
ANT1 |
5180 | 16.7 | -33.1 | -73 | |||
| 5500 | 16.6 | -33.2 | -73 | ||||
| 5825 | 16.9 | -32.9 | -73 | ||||
|
802.11ax(HE20_MCS11) |
ANT0 |
5180 | 13.8 | -38.6 | -59 | ||
| 5600 | 13.7 | -36.8 | -59 | ||||
| 5825 | 13.1 | -38.4 | -59 | ||||
|
ANT1 |
5180 | 13.8 | -38.8 | -59 | |||
| 5600 | 13.2 | -39.4 | -59 | ||||
| 5825 | 13.6 | -38.5 | -59 | ||||
|
802.11ax(HE80_MCS11) |
ANT0 |
5290 | 12.2 | -36.8 | -54 | ||
| 5690 | 11.8 | -37.9 | -54 | ||||
| 5775 | 12.3 | -37.1 | -54 | ||||
|
ANT1 |
5290 | 12.8 | -37.4 | -54 | |||
| 5690 | 12.9 | -37.8 | -54 | ||||
| 5775 | 13 | -36 | -54 | ||||
|
802.11ax(HE160_MCS1 1) |
ANT0 |
5250 | 11.9 | -36.4 | -51 | ||
| 5570 | 11.6 | -36.5 | -50 | ||||
|
ANT1 |
5250 | 12.2 | -37.1 | -51 | |||
| 5570 | 12.1 | -36.6 | -51 | ||||
| 6G Real-world Testing | |||||||
|
Protocol Standard |
channel |
Power (dBm) |
EVM(dB) |
Rx Sensitivity (dBm) | |||
|
802.11a(54Mps) |
ANT0 |
6015 | 14.3 | -31.6 | -73 | ||
| 6515 | 13.4 | -33.4 | -73 | ||||
| 7115 | 13.8 | -33.6 | -73 | ||||
|
ANT1 |
6015 | 14.5 | -33 | -73 | |||
| 6515 | 14.3 | -39.7 | -73 | ||||
| 7115 | 13.5 | -32.8 | -73 | ||||
|
802.11ax(HE20_MCS11) |
ANT0 |
6015 | 13.1 | -38.3 | -59 | ||
| 6515 | 12.5 | -38.7 | -59 | ||||
| 7115 | 12 | -38.3 | -59 | ||||
|
ANT1 |
6015 | 12.9 | -36.5 | -59 | |||
| 6515 | 12.1 | -40.2 | -59 | ||||
| 7115 | 12.8 | -37.1 | -59 | ||||
|
802.11ax(HE80_MCS11) |
ANT0 |
5985 | 11.6 | -36.9 | -54 | ||
| 6545 | 11.6 | -36.8 | -54 | ||||
| 7025 | 11.1 | -37.9 | -54 | ||||
|
ANT1 |
5985 | 11.6 | -37.2 | -54 | |||
| 6545 | 11.3 | -37.2 | -53 | ||||
| 7025 | 11.1 | -37.3 | -54 | ||||
| 802.11ax(HE160_MCS1 1) |
ANT0 |
6025 | 11.1 | -37.2 | -51 | ||
| 6505 | 11 | -37.7 | -50 | ||||
| 6985 | 10.4 | -37.4 | -50 | ||||
|
ANT1 |
6025 | 10.5 | -37.6 | -51 | |||
| 6505 | 10.7 | -37 | -50 | ||||
| 6985 | 10.1 | -36.2 | -50 | ||||
Host Interface Timing Diagram
6.1 PCIe powerup sequence timing Supports PCIe Gen 3 interface for WLAN.
Compliant to PCIe Gen 3 powerup sequence timing. 
Package
7.1 Reel
7.2 Storage Temperature And Humidity
The Modules is a Moisture Sensitive Device level 3, in according with standard IPC/JEDEC J-STD-020, take care all the relatives requirements for using this kind of components.
Moreover, the customer has to take care of the following conditions:
a） Calculated shelf life in sealed bag: 12 months at <40°C and <90% relative humidity (RH).
b） Environmental condition during the production: 30°C / 60% RH according to IPC/JEDEC J-STD-033A paragraph 5.
c） The maximum time between the opening of the sealed bag and the reflow process must be 168 hours if condition.
d） “IPC/JEDEC J-STD-033A paragraph 5.2” is respected.
e） Baking is required if conditions b) or c) are not respected.
f） Baking is required if the humidity indicator inside the bag indicates 10% RH or more.
Refer to KDB 996369 D3 section 2
:2.2 List of applicable FCC rules
FCC Part 15.247, FCC Part 15.407
2.6 RF exposure considerations
This equipment complies with the FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and any part of your body.
2.7 Antennas
This product has three external antennas. The antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.
| No. | Antenna Type | Gain | Impedance |
| 1 | External uniqueness Antenna | 2400-2500:3.0 dBi
5150-5875: 3.1 dBi 5925-7125: 3.5 dBi |
50ohm |
| 2 | External uniqueness Antenna | 50ohm | |
| 3 | External uniqueness Antenna | 50ohm |
2.8 Label and compliance information
Remind end customers to FCC ID label on the final system must be labeled with “Contains FCC ID: 2AT5W-O2066PM” or “Contains transmitter module FCC ID: 2AT5W-O2066PM”.
2.9 Information on test modes and additional testing requirements
Contact SHENZHEN OFEIXIN TECHNOLOGY LIMITED will provide stand-alone modular transmitter test mode. Additional testing and certification may be necessary when multiple modules are used in a host.
2.10 Additional testing, Part 15 Subpart B disclaimer
To ensure compliance with all non-transmitter functions the host manufacturer is responsible for ensuring compliance with the module(s) installed and fully operational. For example, if a host was previously authorized as an unintentional radiator under the
Supplier’s Declaration of Conformity procedure without a transmitter certified module and a module is added, the host manufacturer is responsible for ensuring that the after the module is installed and operational the host continues to be compliant
with the Part 15B unintentional radiator requirements. Since this may depend on the details of how the module is integrated with the host, SHENZHEN OFEIXIN TECHNOLOGY LIMITED shall provide guidance to the host manufacturer for compliance with
the Part 15B requirements.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance.
This module certified that complies with RF exposure requirement under mobile or fixed condition, this module is to be installed only in mobile or fixed applications. A separate approval is required for all other operating configurations, including portable
configurations with respect to Part 2.1093 and difference antenna configurations. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
FCC Warning
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
NOTE 1: This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This product generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this product does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE 3: Any modifications made to the module will void the Grant of Certification, this module is limited to OEM installation only and must not be sold to end-users, end-user has no manual instructions to remove or install the device, only software or
operating procedure shall be placed in the end-user operating manual of final products.
NOTE 4: The module may be operated only with the antenna with which it is authorized. Any antenna that is of the same type and of equal or less directional gain as an antenna that is authorized with the intentional radiator may be marketed with, and used with, that intentional radiator.
NOTE 5: For all products market in US, OEM has to limit the operation channels to CH1 to CH11 for 802.11b/g/n-HT20 and CH3 to CH9 for 802.11n-HT40 by supplied firmware programming tool. OEM shall not supply any tool or info to the end-user regarding to Regulatory Domain change.
NOTE 6: The Module be installed in host systems at the factory by the OEM integrator. Operation is subject to the following two conditions:
(1) Prohibited for control of or Communications with unmanned aircraft systems, including drones.
(2) Prohibition on direct connections to the internet (must be via a low-power indoor access point).
Documents / Resources
 |
OFLY COMM O2066PM Wi-Fi Tri-band 2x2 MIMO DBS Bluetooth 5.2 Module [pdf] User Manual 2AT5W-O2066PM, 2AT5WO2066PM, FWAAO2066PM10, FWAAO2066PM20, O2066PM Wi-Fi Tri-band 2x2 MIMO DBS Bluetooth 5.2 Module, O2066PM, Wi-Fi Tri-band 2x2 MIMO DBS Bluetooth 5.2 Module, Tri-band 2x2 MIMO DBS Bluetooth 5.2 Module, 2x2 MIMO DBS Bluetooth 5.2 Module, MIMO DBS Bluetooth 5.2 Module, DBS Bluetooth 5.2 Module, Bluetooth 5.2 Module, Module |