LED 013010 Wi-Fi DMX Touch Panel Controller Kits
2021
INSTALLATION & OPERATION MANUAL 
WWW.OCEANLED.COM
LIGHT .YEARSAHEAD .
OceanLED MANUAL/CONTROLLERS/WiFi DMX TOUCH/REVISION 0.1
Preface
READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL
WARNINGS
Before installing your DMX Controller, read and follow all warning notices and instructions which are included. Failure to follow safety warnings and instructions can result in property damage, severe injury or even death.
Before installing your DMX Controller, check local laws for restrictions regarding the use of colored lights in your area.
Salt is an inherently corrosive material. Natural and man-made surfaces are susceptible to corrosion and deterioration when used in and around saltwater. Some combinations of plastic and polymer products are impervious to saltwater corrosion, however, screws and fasteners used for the installation must be of a marine-grade type stainless steel or equivalent and monitored annually to ensure the controller remains in service for years to come.
Never Use Solvents! Cleaners, fuel, and other products that may contain strong solvents, such as acetone, attack many plastics greatly reducing their strength and can cause irreversible damage.
Units are not waterproof. You must mount in a dry location. When installing, be sure that the controller fits
the area and secures to the mounting location using the appropriate hardware before installing.
DANGER
RISK OF ELECTRIC SHOCK OR ELECTROCUTION
This unit must be installed by a licensed or certified electrician in accordance with all applicable local codes and ordinances. Improper installation will create an electrical hazard that could result in death or serious injury to installers, or others due to electrical shock, and may also cause damage to property. Always disconnect the power to the light at the circuit breaker before servicing the light. Failure to do so could result in death or serious injury to a serviceman, or others due to electrical shock.
PRETEST
Always test the system prior to installation. Failure to do this may result in additional installation time and could invalidate the warranty.
IMPORTANT NOTICE
Attention Installer: This manual contains important information about the installation, operation, and safe use of this product. This information should be given to the owner and/ or operator of this equipment.
WARRANTY COVERAGE
Please refer to www.oceanled.com/downloads for a full warranty statement.
Overview
Units are not waterproof. You must mount in a dry location. When installing, be sure that the controller fits the area and secures to the mounting location using the appropriate hardware before installing.
TOOLS AND MATERIALS
Never use power tools. Hand tightens only!
- Drill & Drill Bits.
- Screw Driver, Phillips #2
- Wire Strippers.
- Tape measure and Ruler or Straight Edge.
- Marking Utensil (Pencil, Sharpie Magic Marker, etc)
FINDING THE MOUNTING LOCATION
- The mounting location needs to be carefully selected to ensure the unit will not be exposed to moisture.
- Ensure that the ambient temperature where the unit is mounted cannot exceed 45°C – Note that engine compartments can easily exceed this.
- The chosen location requires access to mains power, space for the routing of the DMX cable to the driver boxes, and also an Ethernet connection to a Wi-Fi router / LAN Wi-Fi for the Wi-Fi controller if the Wi-Fi function is required.
For DC power installations please contact OceanLED for advice
SPECIFICATIONS
- Ready to use (pre-loaded with scenes).
- Glass Touch Panel with graphical color display
- Micro SD Card (32Gb Max)
- 6-7V DC / 100-240V AC (With Adapter)
- Environment IP20, Temp -10˚C to 45˚C
- Certifications: CE, EMC, ROHS, ETL
- Dimensions 146x106x11mm
- Weight 247g
Installation
CONNECT THE WIRES (EXPLORE E6 & E7)
- Connect the control cable to the green connector (as below)
• DMX Ground = Black
• DMX – = Brown
• DMX + = Yellow
• Red wire (Unused, do not connect) - Connect power via the AC/DC adapter provided.
• Power DC + = Black/White Stripe
• Power DC – = Black
CONNECT THE WIRES (PRO SERIES) - Connect the control cable to the green connector (as below)
• DMX Ground = Brown & Brown/White (two wires)
• DMX – = Orange
• DMX + = Orange/White - Connect power via the AC/DC adapter provided.
• Power DC + = Black/White Stripe
• Power DC – = Black
MOUNT IN A DRY LOCATION 
- Plug the green connector block into the rear of the DMX Wi-Fi Touch Panel Controller.
- For Wi-Fi plug the local ethernet cable into the rear of the DMX Wi-Fi touch panel controller (Ensure the correct RJ45 port is used):
- Mount the backplate of the interface on the preferred dry mounting location.
- Close the unit by clipping the front panel onto the backplate.
FINALISE YOUR INSTALLATION (EXPLORE E6 & E7)
Always test the system BEFORE the boat goes back into the water. Typical OceanLED light installs require the boat to be hauled out of the water to replace light units.
The DMX standard recommends a maximum of 32 devices to be connected in one chain. If the installation requires more lights than this, please contact OceanLED for advice.
- If Wi-Fi is required connect the Ethernet cable from the back of the controller panel into a suitable Wi-Fi router or Wi-Fi-enabled network. (The controller is DHCP enabled as standard so should be detected by the network once powered).
- Connect the control cable to the control input of the first Explore E6 light. Then connect a control link cable to the next, and so on up to the last light in the chain.
- Fit the supplied terminator to the output of the last E6 light. See the following example of the connections:
Always test the system BEFORE the boat goes back into the water. Typical OceanLED light installs require the boat to be hauled out of the water to replace light units.
The DMX standard recommends a maximum of 32 devices to be connected in one chain. If the installation requires more lights than this, please contact OceanLED for advice. - If Wi-Fi is required connect the Ethernet cable from the back of the controller panel into a suitable Wi-Fi router or Wi-Fi-enabled network. (The controller is DHCP enabled as standard so should be detected by the network once powered).
- Connect the DMX controller DMX output cable to the DMX input of the first driver box. The DMX output of this box should be connected to the input of the next, and so on up to the last driver in the chain.
- Fit the supplied terminator to the output of the last driver box. See the following example of the connections:
Operation
POWER / SCENE SELECTION
- Power on the unit by touching the top center button.
- Select the required scene by using the buttons under the ‘Select Area’ buttons below the display to select the required area and select the scene by touching the left/right arrows on either side of the display. Once the required scene is selected, play that scene, press the ‘Play Scene’ button.
PRE-PROGRAMMED SCENES – EXPLORE
| Explore Dual White / Blue | ||
| Scene | Number | Function |
| Solid Colors |
White | White |
| Blue | Blue | |
| Blue/White | Blue 50% White 50% Mix | |
| Dynamic Modes |
White Stub | White Strobe |
| Blue Stub | Blue Strobe | |
| B/W Stub | Blue / White Strobe | |
| BW Cycle | Blue / White Cycle | |
| Solid Colors |
Red | Red |
| Orange | Orange | |
| Yellow | Yellow | |
| Green | Green | |
| Blue | Blue | |
| Indigo | Indigo | |
| Violet | Violet | |
| White | White | |
| Red 2 | Red Shade – 2 | |
| Red 3 | Red Shade – 3 | |
| Green 2 | Green Shade – 2 | |
| Green 3 | Green Shade – 3 | |
| Blue 2 | Blue Shade – 2 | |
| Blue 3 | Blue Shade – 3 | |
| White 2 | White Shade – 2 | |
| White 3 | White Shade – 3 | |
| Dynamic Modes |
RGB Cycle | Red Green Blue Cycle |
| RGBW Cycle | Red Green Blue White Cycle | |
| R-B Cycle | Red Blue Cycle | |
| G-B Cycle | Green Blue Cycle | |
| B-W Cycle | Blue White Cycle | |
| G-W Cycle | Green White Cycle | |
| R-W Cycle | Red White Cycle | |
| R-G Cycle | Red Green Cycle | |
| Multi Strobe | Multi Strobe | |
| RGB Strobe | RGB Strobe – Red Green Blue Strobe | |
| RGBW Strobe | RGBW Strobe – Red Green Blue White Strobe | |
| R-B Strobe | Red Blue Strobe | |
| G-B Strobe | Green Blue Strobe | |
| R-B-W Strobe | Red Blue White Strobe | |
| G-W-R Strobe | Green White Red Strobe | |
Troubleshooting
|
Wi-Fi DMX Touch Panel Controller |
|||
| Problem | Check | Cause |
Fix |
| DMX controller does not power on | Check Power to Controller is on | No Power | Connect Power |
| Power OK | Check Connections | ||
| Check Connections to controller faceplate | Connected incorrectly | Correct Connections | |
| Connected OK | Contact Warranty Department | ||
| Lights do not respond to the controller and/or random flickering of lights/colors | Check DMX connection is daisy-chained between a controller and all drivers |
Not connected correctly | Correct cabling connections |
| Check all other cables are connected correctly and are not damaged |
Not connected correctly | Correct connections | |
| Damaged cable | Replace Cable | ||
| Check Terminator is fitted to last driver box | Terminator not fitted | Fit terminator | |
| Terminator fitted | Contact Warranty Department | ||
| WiFi not working (only applicable to wi-fi model) |
Check Ethernet cable is connected into the back of the controller panel correctly. | Not connected | Reconnect cable |
| Check the controller panel is recognized on the connected network. |
Controller not visible | Try re-booting the network hub and controller panel. | |
| Check connected network WiFi is functioning correctly | WiFi not functioning | Resolve issue with network WiFi | |
| WiFi network OK | Contact Warranty Department | ||
Warranty
Please remove this page and keep for your files For technical assistance:
Europe: service@oceanled.com
The Americas: warranty@oceanledusa.com
Warranty Serial Code(s):
| © 2021 Ocean LED Marine LTD All Rights Reserved Specifications are subject to change without notice. Trademarks are the property of Ocean LED Marine LTD |
Ocean LED Marine LTD Unit 1 Jacknell Road Dodwells Bridge Industrial EstateHinckley, Leicestershire LE10 3BS United Kingdom Tel: +44 (0) 1455 637505 Fax: +44 (0) 1455 238553 sales@oceanled.com |
Ocean LED USA LLC 778 South Military Trail Deerfield Beach Florida FL 33442-3025 USA Tel: +1 954.523.2250 Fax: +1 954.523.2249 sales@oceanledusa.com |
Documents / Resources
 |
Ocean LED 013010 Wi-Fi DMX Touch Panel Controller Kits [pdf] User Manual 013010 Wi-Fi DMX Touch Panel Controller Kits, 013010, Wi-Fi DMX Touch Panel Controller Kits |
