Tuya H3-WiFi Acess Controller Reader WiFi Version
MAU OYAMBA
Chipangizocho ndi chitseko chimodzi cha multifunction standalone access controller kapena Wiegand output reader. Imagwiritsa ntchito Atmel MCU kutsimikizira magwiridwe antchito. Ntchitoyi ndi yosavuta kugwiritsa ntchito, ndipo dera laling'ono lamagetsi limapangitsa kuti likhale moyo wautali wautumiki.
Chipangizochi chimathandizira ogwiritsa ntchito 1,000 (ogwiritsa ntchito wamba 990 + 10 ogwiritsa ntchito alendo), ndipo deta yonse ya ogwiritsa ntchito imatha kusamutsidwa kuchokera kwa wina kupita ku ina Imathandizira mitundu yofikira pamakhadi, mwayi wa PIN, kapena ma multi-card/PIN. Ili ndi zina zowonjezera kuphatikiza kulembetsa kwa block, kulowetsa kwa Wiegand & mawonekedwe otulutsa ... etc.
Mawonekedwe
- WiFi 2.4G network
- Kiyi Yokhudza
- Zosalowa madzi, zimagwirizana ndi IP66
- Kutumiza kumodzi, ogwiritsa ntchito 1,000 (990 wamba + alendo 10)
- PIN kutalika: 4-6 manambala
- EM khadi, EM + Mifare makadi osankha
- EM khadi: Wiegand 26 ~ 44 bits zolowetsa & zotulutsa
- Khadi la Mifare: Wiegand 26 ~ 44bits, 56bits, 58bits athandizira & zotuluka
- Itha kugwiritsidwa ntchito ngati wowerenga Wiegand wokhala ndi LED & buzzer output
- Kulembetsa khadi block
- Chiwonetsero cha mawonekedwe amtundu wamitundu itatu
- Pulse mode, Toggle mode
- Zogwiritsa ntchito zitha kusamutsidwa
- Kuwala kodalira kuwala (LDR) kwa anti-tamper
- Makiyipi owunikira kumbuyo amatha kuzimitsa zokha pakadutsa masekondi 20
Kufotokozera
Mtengo wa Carton Inventory
KUYANG'ANIRA
- Chotsani chophimba chakumbuyo ku unit
- Boolani mabowo awiri (A, C) pakhoma la zomangira ndi bowo limodzi la chingwe
- Gwirani mphira zomwe zaperekedwa kumabowo omangira (A, C)
- Konzani chophimba chakumbuyo mwamphamvu pakhoma ndi zomangira 4 zosalala
- Dulani chingwe kudzera pabowo la chingwe (B)
- Gwirizanitsani chipangizochi ku chivundikiro chakumbuyo
Wiring
Chizindikiro cha Phokoso ndi Kuwala
Basic Configure
Lowetsani ndikutuluka mumachitidwe apulogalamu
Khazikitsani Master Code
Khazikitsani Njira Yogwirira Ntchito
Ndemanga:
Chipangizocho chili ndi mitundu itatu yogwirira ntchito: Njira Yoyimilira, Njira Yowongolera, ndi Wiegand Reader Mode, sankhani mtundu womwe mumagwiritsa ntchito. (Factory default ndi Standalone Mode/Controller Mode)
STANDALONE mode
Chipangizocho chitha kugwira ntchito ngati Standalone Access Control pakhomo limodzi. (Mawonekedwe osasinthika a Factory) - 7 7 #
Chithunzi cholumikizira
Common Power Supply
Chenjerani:
Ikani 1N4004 kapena diode yofanana ndiyofunika mukamagwiritsa ntchito magetsi wamba, kapena kiyibodi ikhoza kuwonongeka. (1N4004 ikuphatikizidwa muzonyamula)
Access Control Power Supply
Kupanga mapulogalamu
Kukonzekera kumasiyana malinga ndi kasinthidwe kofikira. Tsatirani malangizo molingana ndi kasinthidwe kanu kofikira.
- Ndemanga:
Nambala ya ID ya ogwiritsa: Perekani ID ya wogwiritsa ntchito khadi / PIN kuti muzitsatira.- Common User ID: 0~989 pa
- ID ya Mlendo: 990~999 pa
ZOFUNIKA: Ma ID a ogwiritsa ntchito sayenera kupititsidwa ndi ziro zotsogola. Kujambulitsa ID ya Wogwiritsa ndikofunikira. Zosintha kwa wogwiritsa ntchito zimafunikira ID ya Wogwiritsa kuti ipezeke.
- Khadi Lapafupi:
- Khadi Lapafupi: EM khadi / EM + Mifare makadi
- PIN: Itha kukhala manambala aliwonse 4 ~ 6
Add Common Users
PIN/ ID ya wogwiritsa ntchito Khadi: 0~989; PIN kutalika: 4-6
Malangizo pa PIN Security (yovomerezeka pa PIN ya manambala 6 okha):
Kuti mukhale otetezeka kwambiri timakulolani kubisa PIN yanu yolondola ndi manambala ena mpaka manambala 9.
ExampPIN ya 123434
Mutha kugwiritsa ntchito **(123434) *kapena ** (123434) (“*” itha kukhala nambala iliyonse kuchokera pa 0~9)
Onjezani Ogwiritsa Ntchito Alendo
(Nambala ya ID ya Wogwiritsa ndi 990 ~ 999; PIN kutalika: 4 ~ 6 manambala) Pali magulu 10 a PIN/makhadi a alendo omwe alipo, ogwiritsa ntchito amatha kufotokozedwa mpaka ka 10 kagwiritsidwe, pakatha nthawi zingapo, mwachitsanzo nthawi 5. , PIN/khadi limakhala lofooka basi.
Chotsani Ogwiritsa
Khazikitsani Relay Configuration
Kukonzekera kwa relay kumakhazikitsa machitidwe a relay yotulutsa poyambitsa.
Khazikitsani Access Mode
Kwa Multi-user access mode, nthawi yowerengera singadutse masekondi a 5, apo ayi, chipangizocho chidzatuluka kuti chikhale choyimirira.
Khazikitsani Alamu Yakumenya
- Alamu yoyimitsa idzachitika pambuyo poti 10 yalephera kulowa (Factory YAZIMWA).
- Itha kukhazikitsidwa kuti ikanize mwayi kwa mphindi 10 mutatha kuchita nawo kapena kusiya pokhapokha mutalowa khadi / PIN kapena Master code / khadi.
Khazikitsani Mayankho Omveka ndi Owoneka
Kugwiritsa Ntchito Makhadi a Master (Ogwiritsa ntchito amatha kuwonjezera Master Card okha)
Ogwiritsa Ntchito & Bwezeretsani ku Factory Default
- Tsegulani chitseko: Werengani khadi yovomerezeka kapena lowetsani PIN yolondola #
- Chotsani Alamu: Lowetsani Master Code # kapena Master Card kapena khadi/PIN yovomerezeka
Kuti mukhazikitsenso ku fakitale yosasinthika & Add Master Card:
Zimitsani, dinani batani Lotuluka, gwirani ndikuyatsa, padzakhala ma beep awiri, kenako tulutsani batani lotuluka, kuwala kwa LED kudzakhala chikasu, kenako werengani khadi iliyonse ya 125KHz EM / 13.56MHz Mifare khadi, LED isintha kukhala red, zikutanthauza bwererani ku fakitale kusakhulupirika bwino. Pakuwerenga kwamakhadi, ndi Master Card.
Ndemanga:
- Ngati palibe Master Card yomwe yawonjezeredwa, muyenera kukanikiza batani Lotuluka kwa masekondi osachepera 5 musanatuluke. (izi zipangitsa Master Card yolembetsedwa kale kukhala yosavomerezeka)
- Bwezerani kukhala wokhazikika wafakitale, zambiri za wogwiritsa ntchito zimasungidwabe.
WOLAMULIRA NTCHITO
Chipangizocho chitha kugwira ntchito ngati Wowongolera, wolumikizidwa ndi wowerenga wakunja wa Wiegand. (Factory default mode) - 7 7 #
Chithunzi cholumikizira
Chenjerani:
Ikani 1N4004 kapena diode yofanana ndiyofunika mukamagwiritsa ntchito magetsi wamba, kapena owerenga atha kuonongeka. (1N4004 ikuphatikizidwa muzonyamula)
Khazikitsani Mawonekedwe Olowetsa a Wiegand
Chonde ikani mawonekedwe a Wiegand potengera mawonekedwe a Wiegand akunja a Reader.
Zindikirani:
Kuti mulumikizane ndi owerenga a Wiegand ndi 32, 40, ndi 56 bits zotuluka, mufunika kuletsa ma parity bits.
Kupanga mapulogalamu
- Basic Programming ndi yofanana ndi Standalone Mode
- Pali zina zomwe mungasankhe:
Chipangizochi chikulumikizidwa ku External Card Reader
- Ngati owerenga makhadi a EM / Mifare: ogwiritsa ntchito amatha kuwonjezeredwa / kuchotsedwa pa chipangizocho kapena owerenga akunja.
- Ngati owerenga makhadi a HID: ogwiritsa ntchito amatha kuwonjezedwa / kuchotsedwa pa owerenga extemal.
Chipangizochi chalumikizidwa ku Fingerprint Reader
Za exampLe:
Lumikizani SF1 ngati chowerengera chala ku chipangizocho.
- Gawo 1: Onjezani chala chala (A) pa SF1 (Chonde onani buku la SF1)
- Gawo 2: Onjezani Fingerprint(A) yomweyo pa chipangizochi:
Chipangizochi chalumikizidwa ku Keypad Reader
- Wowerenga keypad akhoza kukhala 4 Bits, 8 Bits (ASCIl), kapena 10 Bits linanena bungwe mtundu.
- Sankhani m'munsimu ntchito malinga Pin linanena bungwe mtundu wa owerenga wanu.
Ndemanga:
4 amatanthauza 4 bits, 8 amatanthauza 8 bits, 10 amatanthauza manambala 10 nambala yeniyeni.
- Onjezani Ogwiritsa Ntchito PIN:
Kuti muwonjezere ogwiritsa ntchito ma PIN, mutalowa m'mapulogalamu pa chipangizocho, maPIN (ma) amatha kulowetsedwa / kuwonjezeredwa pa chipangizocho kapena pa Keypad Reader yakunja. - Chotsani Ogwiritsa Ntchito PIN: momwemonso kuwonjezera ogwiritsa ntchito.
WIEGAND REDER MODE
Chipangizocho chitha kugwira ntchito ngati Standard Wiegand Reader, yolumikizidwa ndi Wowongolera wachitatu - 78 #
Chithunzi cholumikizira
Ndemanga:
- Mukayikidwa mu Wiegand Reader mode, pafupifupi zokonda zonse mu Controller Mode zidzakhala zosavomerezeka, ndipo mawaya a Brown & Yellow adzafotokozedwanso motere:
- Brown waya: Kuwongolera kuwala kwa LED kobiriwira
- Yellow Waya: Kuwongolera kwa buzzer
- Ngati mukufuna kulumikiza mawaya a Brown/Yellow:
Pamene athandizira voltage kwa LED ndi yotsika, LED idzasanduka Green; ndi pamene voltage chifukwa Buzzer ndiyotsika, idzamveka.
Khazikitsani Mawonekedwe a Wiegand Output
Chonde khazikitsani mawonekedwe a Wiegand a Reader molingana ndi mawonekedwe a Wiegand a Controller.
Zindikirani:
Kuti mulumikizane ndi chowongolera cha Wiegand ndi 32, 40, ndi 56-bit, muyenera kuletsa ma bits.
KUGWIRITSA NTCHITO KWAMBIRI
Njira Yosonkhanitsira Khadi
Akatsegula mode iyi, makadi onse akhoza kutsegula loko. Panthawi imodzimodziyo, khadi likuwonjezeredwa ku chipangizocho.
Kusamutsa Zambiri Zogwiritsa Ntchito
Chipangizochi chimathandizira Ntchito Yotumiza Mauthenga Ogwiritsa Ntchito, ndipo wogwiritsa ntchito (makadi, ma PIN) akhoza kusamutsidwa kuchokera kumodzi (tiyeni titchule Master Unit) kupita ku wina (tiyeni titchule kuti Accept Unit).
Chithunzi cholumikizira:
Ndemanga:
- Mayunitsi a Master ndi Accept mayunitsi ayenera kukhala zida zofanana.
- Master Code ya Master Unit ndi Unit Accept iyenera kukhazikitsidwa mofanana.
- Konzani ntchito yosinthira pa Master Unit yokha.
- Ngati Accept Unit ili kale ndi ogwiritsa ntchito omwe adalembetsa, idzaphimbidwa pambuyo posamutsa.
- Kwa ogwiritsa 1000 athunthu omwe adalembetsa, kusamutsa kumatenga pafupifupi masekondi 30.
Khazikitsani Kusamutsa pa Master Unit:
Zolemba / Zothandizira
 |
Tuya H3-WiFi Acess Controller Reader WiFi Version [pdf] Buku Logwiritsa Ntchito ch1-cf1, H3-WiFi, H3-WiFi Acess Controller Reader WiFi Version, H3-WiFi, Acess Controller Reader WiFi Version, Controller Reader WiFi Version, Reader WiFi Version, WiFi Version, Version |