INSTRUCTION SHEET
CSBS1, CSBS1A, CSBS2
Single Side Flange Attachments
CSBS1 Single Side Flange Attachments
| *Part Number | Flange Thickness | ||
| Global | Article | Inch | mm |
| CS BS 1 | 404504 | 1/4 to 3/4 | 6 to 19 |
| CSBS1A | 404505 | ||
| CSBS2 | 404506 | 3/4 to 1-1/4 | 19 to 31 |
*Part Number are EG Plating. Other Coatings are available.
The required type, number and size of fasteners used for the structure attachment fitfing shall be in accordance with NFPA 13.
Sway brace assemblies are infended fo be installed in accordance with NFPA 13 and the manufacturer’s installafion instructions 
| UL Loads (Listed for Structural Attachment) | |||||||
| Part Number | Structure Attachment Fitting |
Flange Thickness | Parallel to Structure Perpendicular to Beam |
Perpendicular to Structure Perpendicular to Beam |
Parallel to Structure Parallel to Beam |
||
| Global | Article | Inch | mm | ||||
| CSBS1 | 404504 | CSBUl | 1/4 to 5/16 | 6 to 8 | 1,5001b (6,672 N) | ||
| 3/8 to 3/4 | 8 to 19 | 1,885 lb (8,385 N) | |||||
| CSBURC12 | 1/4 to 3/4 | 6 to 19 | 1,100 lb (4,893 N) | ||||
| CSBS1A | 404505 | CSBUl | 1/4 to 5/16 | 6 to 8 | 1,500 lb (6,672 N) | ||
| 3/8 to 3/4 | 8 to 19 | 1,885 lb (8,385 N) | |||||
| CSBS2 | 404506 | CSBU 1 | 3/4 to 1-1/4 | 19 to 31 | 1,704 lb (7580 N) | ||
| CSBURC12 | 1,100 lb (4,893 N) | ||||||
1. Structure Attachment Fittings are not Included with the CSBS1 or the CSBS2
WARNING:
- nVent products shal be installed and used only as indicated in nVent product insiruction sheets and fraining materials. Insiruction sheets are ovaiable ot www.nVent.com and from your nVent customer service representative.
- nVent products must never be used for a purpose ofher than the purpose for which they were designed orin a manner that exceeds specified load ratings.
- Al insiructions must be complefely followed fo ensure proper and safe insidllation and performance.
- lmproper nstalation, misuse, miappicafion or other fakre fo completel follw nVen! s insuctions and warnings may cause product mauncion, property damage, serious bodily injury and/or death, and void your warmanty.
- Products fhat are manufaciured using spring sieel components shall be used only in a non-corosive indoor environment.
- Allpipe supports, hangers. nfermediate components and siructural affochmens must ONLY be used as described herein ond ore NEVER fo be used for any other purpose.
NOTE: Alload rafings are for stafic condifions and do not account for dynamic loading such os wind, water or seismic loads, unless ofhenwise noted
The customer is responsible for:
a. Conformance to all governing codes
b.The infegriy of sirucfures fo which the products are aftached, including fheir capabiiy of safely accepfing the loads impesed, as evaluated by a qualified engineer.
c. Using appropriate indusiry standard hardware as noted above.
SAFETY INSTRUCTIONS:
Al governing codes and reguiafions and those required by the job site must be observed.
Always use appropriate safefy equipment such as eye profection, hard hat, and gloves as appropriate fo the application.
| Part Number | Orientation | FM Horizontal Load Ratings | ||||
| Global | Article | Installation Angle | ||||
| 30° – 44° | 45° – 59° | 60° – 74° | 75° – 90° | |||
| CSBS1 | 404504 | Lateral | 850 lb (3,780 N) |
1780 lb (7,910 N) |
2,770 lb (12,320 N) |
2,840 lb (12,630 N) |
| CSBS1A | 404505 | |||||
| CSBS2 | 404506 | 1,220 lb (5,420 N) |
2,140 lb (9,510 N) |
2,580 lb (11,470 N) |
2,870 lb (12,760 N) |
|
| CSBS1 | 404504 | Longitudinal | 880 lb (3910 N) |
1,430 lb (6,360 N) |
2,020 lb (8,980 N) |
2,410 lb (10,720 N) |
| CSBS1A | 404505 | |||||
| CSBS2 | 404506 | 1,100 lb (4,890 N) |
1,820 lb (8,090 N) |
2,190 lb (9,740 N) |
2,680 lb (11,920 N) |
|
1. EN 10255 (Heavy), AS 1074 Heavy or JIS G3454 brace pipe.
FM Approved when used with 1″, 1-1/4″, 1-1/2″, or 2″ (DN25, DN32, DN40, DN50) NPS Schedule 40, GB/T 3091, 
nVent, nVent CADDY, nVent ERICO Cadweld, nVent ERICO Critec, nVent ERICO, nVent ERIFLEX, and nVent LENTON are owned by nVent or its global affiliates. All other trademarks are the property of their respective owners. nVent reserves the right to change specifications without prior notice.
TECHNICAL SUPPORT:
www.nVent.com
CFS541_G
3 OF 3
© 2016-2020 nVent All Rights Reserved
Documents / Resources
 |
nVent CSBS1 Single Side Flange Attachments [pdf] Instructions CSBS1 Single Side Flange Attachments, CSBS1, Single Side Flange Attachments, Side Flange Attachments, Flange Attachments |
