Quick Start Guide
Welcome
The Smart Node 5G provides enhanced 5Gservicewithinbuildings. It delivers high quality 5G, mobile data service.
The Smart Node 5G connects to your broadband Internet service to deliver an extended indoor mobile network coverage. The in-building mobile phone connectivity, signal quality, and data bandwidth will improve, especially if the buildingis inaremotearea or out of adequate mobilephonetower range.
Inside this packaging you will find the Smart Node and its accessories necessary for the installation. The Smart Node has a zero touch set-up process. Just install as detailed in this guide and it connects to your mobile phone automatically whenever your phone is within range.
Beforeyoubegin youneed tomake sureyou havethefollowing:
- Smart Node 4G* already deployed and operational (Clip-on Only)
- High speedintemet service and an available Ethemnet LAN port on your router.
- Anavailable power socket or electrical outlet.
- A5G phone registered for 5G service with your service provider.
*SN5177 can be used only in combination witha 4G SN4IBN certified product (FCC ID:V4VISN4IBN)
SN5178 can be used only in combination with a 4G SN4ICG certified prodtct.
Box Content (Clip-On)
Box Content (Stand Alone dnly)
Connection Overview
All Smart Node Variants with BH Module
Reset
- Pressand hold for 5 seconds for reboot.
- Press and hold for 20 seconds for factory setting reset and software update.
WARNING: The interface ports of the Smart Node are suitable for connection to intra-building or unexposed wiring or cabling only. The intra-building ports of the Smart Node MUST NOT be metallically connected to interfaces that connect to the OSP or its wiring for more than 6 meters (approximately 20 feet). These interfaces are designed for use as intra-building interfaces only (Type 2, 4, or 4a ports as described in GR-1089) and require isolation from the exposed OSP cabling. The addition of Primary Protectors is not sufficient protection in order to connect these interfaces metallically to an OSP wiring system
Quick Setup
- Remove the face plate of the 4G Smart Node and Plug in the 5G Smart Node module (Clip-On Only)
Power down the deployed 4G Smart Node. Remove the faceplate using the tool provided; plug in the 5G smart node on top of the 4G Smart Node until they “click”.
- Connect Your Smart Node to the Internet
Connect the Ethernet cable from the yellow “WAN” port on your Smart Node to an available Ethernet port on your internet router. - Connect GPS Antenna to Smart Node
Connect the GPS antenna cable to the GPS port. Position the antenna outside the home where sky visibility is there or place it as close to a window as possible. - Power onyour Smart Node
Plug in your AC power adaptor into the power outlet and connect the power cable to the Smart Node power port.
Let your Smart Node auto-configuration run…
After you power on your Smart Node, for the first time, it will go through selfinstallation. It can take up to 45 minutes to complete the device setup. Your Smart Node may download updates and restart during this time. Once self-installation is complete, typical boot-up time will be less than 5 minutes.
Quick Setup
- Power (SolidWhite)
Power on. Device self-testing and update complete. - Internet (Solid White)
Successful internet connection. - Status (Solid White)
Successful connection established with mobile operator network. - GPS (Solid White)
Successful connection established with the Global Satellite System - 4G C1(Solid White)
Device is readly to provide 4G service for Carrier 1. - 4G C2 (Solid White)
Device is readly to provide 4G service for Carrier 2. - 4G C2 is off/unlit in case only one LTE cell is enabled.
- 5G (Solid Green)
Device is readly to provide 5G service
Flexible mount options are available for the Smart Node.
Wall mounting or ceiling mounting (accessories included in the 4G or 5G Stand Alone box).
Table, desk or flat surface mounting (not included in the box , optional accesory )
Congratulations! Your Smart Node setup is complete.
You should see improved signal strength from your device. Make your first call to enjoy more dependable voice calls and more reliable high- speed data connection.
Common Troubleshooting Procedures
| Issue Description and Resolution | Power | Internet | Status | GPS | 4G CH1 | 4G CH2 | 56 |
| Device has a hardware issue. | Solid Orange |
Solid Orange |
Solid Orange |
Solid Orange |
Solid Orange |
Solid Orange/Off |
Solid Orange/Off |
| Tamper Detected Product has a temper alarm. Radio and all other components have been turned off. |
Solid Orange |
Solid Orange |
Solid Orange |
Flashing Orange | Flashing Orange | Flashing Orange/off | Flashing Orange/off |
| Network Attach failure Device could not access local network (Ethernet or DHCP failure, could ot reach SeGW). | solid White |
Solid Orange |
Off | Any | Off | Off | Off |
| Failed to contact SeGW Jnit completed DHCP but could not contact the SeGW. |
Solid White |
Flashing Orange |
Off | Any | Off | Off | Off |
| SeGW authentication failure. Unit contacted SeGW but failed. to establish IPSec tunnel. | Solid White |
Solid White |
Solid Orange |
Any | Off | Off | Off |
| 4G FGW Connection failure Failed to connect to the 4G Femto Gateway. | Solid White |
Solid White |
Flashing Orange | Any | Off | Off | Off |
| LTE at full capacity LTE cell has reached configured maximum number |
Any | Any | Flashing White | Any | Flashing White |
Off | Off |
| No GPS Signal Device is not able to capture GPS signal. |
Any | Any | Any | Solid Orange |
Any | Off | Off |
| Searching for satellites | Any | Any | Any | Flashing white |
Any | Off | Off |
| Environment failure The device is overheated. Move device to a cooler location. |
Flashing Orange | Flashing Orange |
Flashing Orange | Flashing Orange |
Flashing Orange |
Flashing Orange/off |
Flashing Orange/off |
How do I know that | am using my Smart Node service?
Your mobile phone display will automatically indicate if you are within small cell signal range. If registered and configured properly, your mobile phone should display a small cell service 'message and an associated signal indlicator.
Will my call drop if | leave the building in the middle of a call?
Ifyoumove outofrange ofthe Smart Nodle, your call will be automatically transferred to the next available network service offered by your mobile service provider, without disconnecting your call. If no other mobile network is available your call will be disconnected.
What happens if my broadband connection fails?
Ifyoulose your broadband connection in cases of IP connectivity set up failure, the Internet light will light solid orange and your Smart Node coverage will stop. The Smart Node service will return when the broadbandconnectionis recovered.
What happens if my Smart Node stops operating — can | still place a call?
IfyourSmart Nodestops operating (eg, if you have lost your broadband connection) then you will no longerbe able to place calls throughthe Smart Node. However, if you have coverage from the mobile network ofyourmobile service provider youcan stillplace calls normally.
FCC Regulations swsi7
This device complies with part 15 of the FCC Rules. Operation is subject to the following two condiitions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiated radlio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or ‘more of the following measures:
Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment.
RF Exposure Information sws
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm (8 inches), in stand alone configuration, and 26 cm (10 inches ) in combination with a 4G unit..
<h4 style="text-align: justify">ISED Notice isnsizs)This device complies with Innovation, Science and Economic Development Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
- this device may not cause interference, and
- this device must accept any interference, including interference that may cause undesired operation of the device. </ol>
<li>
This device complies with the Canadian ICES-003 Class B specifications.
CAN ICES-003(B)/ NMB-003(B)
IC: 661AF-SN5I78
ISED RF Exposure Statement isnsis
This device complies with ISED RSS-102 RF exposure limits set forth for an uncontrolled environment In order to avoid the possibility of exceeding the IC RSS-102 RF exposure limits, human proximity to the antenna shall not be less than 20cm (8 inches) during normal operation.
“TRADEMARKS: Nokia and the Nokia logo are registered trademarks of Nokia.
All other trademarks are the property of the respective owners.
20230714
Documents / Resources
 |
NOKIA SN5I77 Node 5G Smart [pdf] User Manual SN5I77 Node 5G Smart, SN5I77, Node 5G Smart, 5G Smart, Smart |
References
