NODESTREAM HT841 4 Port Analog FXO Gateway
Specifications
- Power Input: 12-28VDC
- Connectivity: LAN, USB, HDMI, RS232 Serial
- Audio: Analog Audio input/output
- Dimensions: 157mm x 52mm x 60mm (Freestanding or mounted)
Overview
Welcome to Nodestream Flex
Please read these instructions carefully before using this product, and save this quick start guide for future reference. See the User Manual for full details via the QR code on the back page.
In the Box
Connections
Connections / UI
- Reset Button
Restart Device – Press 2 seconds & release
Factory reset device
- Status LED
RGB LED to indicate system status
BLUE – System starting GREEN – Solid (streaming), Flashing (idle) RED – Network issue - LAN 1
Gigabit Ethernet - LAN 2
Gigabit Ethernet - USB A 3.0
Connection of peripherals such as keyboard/mouse, camera - Analog Audio
Connection of analog audio input/output peripherals - HDMI Inputs
Video source inputs (Encoder mode only) - HDMI Video Wall Outputs
(Decoder mode only) - RS232 Serial
3.5mm TRRS. (/dev/ttyTHS0)
- HDMI Out
“Pasthrough” display output - Power Switch
On / Off - Power Input
12-28VDC
Power redundancy is available for this device, Refer to the device User Manual for additional information.
Installation
Dimensions
Freestanding or mounted using the supplied surface mount adapters or optional 19” rackmount shelf.
- Ensure adequate space around heat sink for cooling
- For ambient temperatures exceeding 35°C, 0.5m/s of airflow across the heatsink is required
Configuration
Web Interface
- Access the Web Interface
Via a computer on the same network
DHCP Enabled Network
From the web browser of a PC connected to the same LAN, navigate to: device serial.local – e.g. au2518nsfx1a012.local, or the IP address of the device
Non DHCP Enabled Network
Configure the IPv4 network settings of a PC connected to the same LAN to:- IP 192.168.100.102
- Subnet 255.255.255.252
- Gateway 192.168.100.100
From a web browser, navigate to: 192.168.100.101 - Device will “fall back” to a static IP address when not connected to a DHCP enabled network – approximately 30 seconds after boot
- Due to the possibility of conflicting IP addresses, only 1 device can be configured at a time. Once configured, the device can remain connected
On the device
- Login in – username & password = admin
- Configure your network
- Select device mode and configure your server on the “System” page
your device will show online in the Harvest Control application
add your device to your Organization via the web portal
User Manual
Refer to the device User Manual for additional information.
Nodestream devices require specific firewall settings to be in place. Refer to the User Manual for further information
Contact and Support support@harvest-tech.com.au
Troubleshooting
| Issue | Cause | Resolution |
| Device not powering | DC not connected Incorrect polarity
Faulty or incompatible supply |
Confirm supply is connected and turned on
Confirm power input cable is connected correctly Test with alternative supply Ensure supply voltage meets required specifications, refer User Manual |
| Nodestream X
“Server Connection Error”
Nodestream Live “Could not resolve hostname”
Status LED RED |
Network not connected Network settings incorrect
Firewall blocking comms |
Check Ethernet cable is connected
Check network settings, contact your Network administrator to diagnose network Ensure Firewall settings correct, see User Manual |
| No video input | Sources not connected, powered
on or correctly configured |
Confirm sources connected and powered on, refer User Manual for configuration |
| Forgot login or network details | N/A | Factory reset to defaults
(refer “Connections / UI” on page 3) |
Harvest Technology Europe (colm.mulcahy@harvest-tech-europe.com ; +353 87 8126761)
Suite 4, Eden Gate Business Centre, Delgany, A63 WY44 Wicklow, Ireland
Dallas Allardice (dallas.allardice@harvest-tech.com.au ; +44 7921567416)
Overton Lodge, Methlick, Ellon, UK, AB41 7HT
Harvest Technology Pty Ltd
7 Turner Ave, Technology Park
Bentley WA 6102, Australia
harvest.technology
All rights reserved. This document is the property of Harvest Technology Pty Ltd. No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic, photocopy, recording or otherwise without the written consent of the CEO of Harvest Technology Pty Ltd.
Documents / Resources
 |
NODESTREAM HT841 4 Port Analog FXO Gateway [pdf] User Guide Nodestream Flex, v1, HT841 4 Port Analog FXO Gateway, HT841, 4 Port Analog FXO Gateway, Analog FXO Gateway, FXO Gateway |