Introduksjon
This manual provides detailed instructions for the assembly, operation, and maintenance of your TecTake 403238 / 800747 Swivel Office Chair. Please read these instructions carefully before assembly and use to ensure proper function and longevity of your product. This ergonomic office chair is designed for comfort and support during extended periods of sitting, featuring a padded seat, backrest, and headrest, along with adjustable height and tilt functions.

Image: The TecTake 403238 / 800747 Swivel Office Chair, showcasing its black faux leather upholstery, padded armrests, and five-star base with casters.
Sikkerhetsinstruksjoner
For å unngå skader på stolen, må du følge følgende sikkerhetsretningslinjer:
- Sørg for at alle komponenter er godt festet før bruk. Kontroller og stram skruene regelmessig.
- Ikke overskrid stolens maksimale vektkapasitet (se spesifikasjoner).
- Unngå å stå på stolen eller bruke den som en krakk.
- Keep hands and fingers clear of moving parts, especially during height and tilt adjustments.
- Bruk stolen på et jevnt underlag for å unngå at den velter.
- Hold emballasjematerialene unna barn for å unngå kvelningsfare.
- Do not expose the chair to direct sunlight or extreme temperatures, as this may damage the material.
Komponentliste
Før monteringen starter, må du kontrollere at alle deler er til stede og uskadet. Hvis noen deler mangler eller er skadet, må du ikke fortsette med monteringen og kontakte kundestøtte.
- Rygg
- Setepute
- Armlener (venstre og høyre)
- Mekanismeplate (under setet)
- Gassløftesylinder
- Gassløftdeksel
- Femstjerners base
- Hjul (5 stk.)
- Hardware (screws, washers, Allen key)
Monteringsveiledning
Follow these steps to assemble your office chair. It is recommended to assemble the chair on a soft, clean surface to prevent scratches.
Step 1: Attach Casters to the Base
Sett hvert av de fem hjulene inn i hullene på enden av hvert ben på femstjernebasen. Trykk godt til de klikker på plass.
Step 2: Insert Gas Lift
Place the gas lift cylinder into the central hole of the five-star base. Then, slide the gas lift cover over the gas lift cylinder.
Step 3: Attach Mechanism Plate to Seat
Align the mechanism plate with the pre-drilled holes on the underside of the seat cushion. Ensure the adjustment lever faces the front of the seat. Secure it with the provided screws and tighten them using the Allen key.

Image: Close-up of the chair's adjustment lever, indicating its function for height and tilt control. This lever is part of the mechanism plate that attaches to the seat.
Step 4: Attach Armrests to Seat and Backrest
Attach the armrests to the sides of the seat cushion using the designated screws. Do not fully tighten yet. Then, align the backrest with the armrests and secure it with screws. Once all screws are in place, tighten them evenly and securely.
Trinn 5: Koble seteenheten til gassløfteren
Carefully place the assembled seat and backrest onto the gas lift cylinder. The tapered end of the gas lift will fit into the central hole of the mechanism plate. Press down firmly on the seat to ensure a secure connection.

Bilde: Foran view of the fully assembled TecTake office chair, highlighting the padded seat, backrest, and armrests.
Your TecTake office chair is now assembled. Before use, ensure all connections are tight and the chair is stable.
Bruksanvisning
Your TecTake office chair offers several adjustments to customize your seating experience:
Høydejustering
To adjust the seat height, locate the lever on the right side, beneath the seat.
- For å heve setet: Lift the lever while taking your weight off the seat. The seat will rise automatically. Release the lever at the desired height.
- For å senke setet: Lift the lever while remaining seated. The seat will lower. Release the lever at the desired height.
Tilt Function and Lock
The chair features a tilt mechanism allowing the backrest and seat to recline together.
- To enable tilt: Pull the same lever (used for height adjustment) outwards from the chair. The chair will now allow you to recline.
- To lock tilt: Push the lever inwards towards the chair. The chair will lock in its upright position.

Image: An illustration demonstrating the range of height adjustment and the reclining tilt function of the office chair.
Justering av tiltspenning
Beneath the seat, at the front, there is a round knob. This knob controls the tension of the tilt mechanism.
- To increase tension (harder to recline): Vri bryteren med klokken.
- To decrease tension (easier to recline): Vri knotten mot klokken.
Vedlikehold
Regelmessig vedlikehold vil bidra til å forlenge levetiden og utseendet til kontorstolen din.
- Rengjøring: Tørk av med en myk klut for trekk i kunstskinn.amp klut. For gjenstridige flekker, bruk en mild såpeløsning og tørk av umiddelbart. Unngå slipende rengjøringsmidler, løsemidler eller sterke kjemikalier, da disse kan skade materialet.
- Ramme og base: Tørk av metall- og plastdeler med annonseamp klut.
- Hjul: Periodically clean casters to remove hair, dust, and debris that may hinder smooth movement.
- Maskinvare: Every 3-6 months, check all screws and bolts to ensure they are tight. Retighten as necessary to maintain stability and safety.
- Unngå overbelastning: Do not exceed the chair's stated weight capacity.
Feilsøking
Hvis du støter på problemer med stolen din, kan du se følgende vanlige problemer og løsninger:
- Stolknirk:
Check all screws and bolts and tighten them. A small amount of silicone lubricant can be applied to moving metal parts, avoiding contact with plastic or upholstery.
- Stolen justerer ikke høyden:
Ensure the gas lift lever is fully engaged. If the issue persists, the gas lift cylinder may be faulty and require replacement. Contact customer support.
- Stolen føles ustabil/vinglete:
Verify that all screws, especially those connecting the armrests to the seat and backrest, are securely tightened. Ensure the gas lift is properly seated in the base and mechanism plate.
- Hjulene ruller ikke jevnt:
Remove any hair, dust, or debris that may be caught in the caster wheels. Clean the wheels and axles. Ensure the casters are fully inserted into the base.
Spesifikasjoner
| Merke | TecTake |
| Modellnummer | 800747 |
| Farge | Svart |
| Materiale | Polyurethane, Faux Leather, Pine Wood (frame) |
| Varevekt | 16.7 kilo |
| Anbefalt bruk | Kontor |
| Spesialfunksjon | Solid konstruksjon |
Dimensjoner (omtrentlig)

Image: Technical drawing illustrating the approximate dimensions of the TecTake office chair in centimeters. Key measurements include seat width (55 cm), seat depth (52 cm), backrest width (48 cm), adjustable seat height (47-55 cm), and overall height (115-123 cm).
- Overall Height: 115-123 cm
- Seat Height (adjustable): 47-55 cm
- Setebredde: 55 cm
- Setedybde: 52 cm
- Backrest Width: 48 cm
- Armrest Height (from seat): 68.5-76.5 cm
- Base Diameter: 67 cm
Garanti og støtte
Specific warranty information for the TecTake 403238 / 800747 Swivel Office Chair is not provided in this document. For details regarding warranty coverage, spare parts availability, or technical support, please refer to the official TecTake website or contact their customer service directly. Information regarding spare parts availability was not provided in the product data.
Du kan besøke TecTake-merkebutikken på Amazon for mer informasjon.





