Alpine SPS-600 6.5-inch Coaxial Car Speaker Instruction Manual

1. Introduksjon

The Alpine SPS-600 is a 6.5-inch 2-way coaxial car speaker system designed to enhance your vehicle's audio experience. These speakers feature a robust design for clear sound reproduction and reliable performance. Key specifications include a power handling capacity of 80 Watts RMS (240 Watts Peak), a frequency response range of 70Hz to 22kHz, and a sensitivity of 88dB /W(1m).

2. Sikkerhetsinformasjon

• Profesjonell installasjon anbefalt: If you are unfamiliar with car audio wiring and installation, it is recommended to seek professional assistance to prevent damage to the speakers or your vehicle.
• Koble fra batteriet: Always disconnect the vehicle's negative battery terminal before beginning any electrical installation to prevent short circuits and electrical hazards.
• Riktig ledning: Ensure all wiring connections are secure and correctly polarized. Incorrect wiring can lead to speaker damage or poor sound quality.
• Monteringssikkerhet: Securely mount the speakers to prevent them from becoming loose during vehicle operation, which could cause injury or damage.
• Unngå overmakt: Do not exceed the speaker's rated power handling capacity (80 Watts RMS / 240 Watts Peak) to prevent damage.
• Ventilasjon: Ensure adequate ventilation around the speakers and any connected ampløftere for å forhindre overoppheting.

3. Pakkens innhold

Kontroller at alle varene er til stede i pakken før du starter installasjonen:

• Alpine SPS-600 6.5-inch Coaxial Speakers (Pair)
• Speaker Grilles (if included)
• Mounting Screws and Clips
• Høyttalerledning (hvis inkludert)
• Installasjonsmal (hvis inkludert)

4. Oppsett og installasjon

This section outlines the general steps for installing your Alpine SPS-600 speakers. Specific vehicle requirements may vary.

4.1. Forberedelse

1. Koble fra den negative polen på kjøretøyets batteri.
2. Remove the existing speakers or trim panels to access the speaker mounting locations.
3. Inspect the mounting location for adequate depth and clearance for the new speakers. The SPS-600 speakers have a 6.5-inch woofer diameter and a 2.54 cm tweeter diameter.

4.2. Montering av høyttalerne

The Alpine SPS-600 speakers are designed for coaxial car mounting.

1. Place the speaker in the desired mounting location. If using an installation template, mark and cut the opening as necessary.
2. Align the speaker's mounting holes with the vehicle's speaker mounts. If new holes are required, drill pilot holes carefully to avoid damaging vehicle components.
3. Fest høyttaleren med de medfølgende monteringsskruene. Ikke stram til for mye.

Front view of the Alpine SPS-600 6.5-inch coaxial car speaker, showcasindens design og komponenter.

4.3. Kablingstilkoblinger

The SPS-600 speakers utilize wired coaxial connectivity.

1. Connect the positive (+) terminal of the speaker to the positive (+) speaker output wire from your head unit or amplivligere.
2. Connect the negative (-) terminal of the speaker to the negative (-) speaker output wire from your head unit or amplivligere.
3. Sørg for at alle tilkoblinger er tette og isolerte for å unngå kortslutning.

4.4. Siste trinn

1. Reinstall any removed trim panels or grilles.
2. Koble til bilens negative batteripol igjen.
3. Test the speaker functionality.

5. Bruksanvisning

Once installed, the Alpine SPS-600 speakers operate as part of your vehicle's audio system. They are designed for stereo audio output.

1. Strøm på: Turn on your vehicle's head unit or audio receiver.
2. Kildevalg: Select your desired audio source (e.g., radio, CD, MP3 player, smartphone connected to the head unit).
3. Volumjustering: Gradually increase the volume to a comfortable listening level. Avoid excessively high volumes that cause distortion, as this can damage the speakers.
4. Lydinnstillinger: Adjust bass, treble, balance, and fader settings on your head unit to optimize sound quality according to your preference. The SPS-600 features a bass boost capability, which can be further enhanced through head unit settings or an external amplivligere.

6. Vedlikehold

Proper maintenance ensures the longevity and performance of your Alpine SPS-600 speakers.

• Rengjøring: Use a soft, dry cloth to gently wipe dust and debris from the speaker cones and grilles. Avoid using harsh chemicals or abrasive cleaners.
• Miljøvern: While designed for vehicle use, avoid exposing speakers to excessive moisture or extreme temperatures. These speakers are not water-resistant.
• Regelmessig inspeksjon: Sjekk regelmessig monteringsskruene for stramning og ledningstilkoblinger for sikkerhet.

7. Feilsøking

If you encounter issues with your Alpine SPS-600 speakers, refer to the following common troubleshooting steps:

8. Spesifikasjoner

9. Garanti og støtte

For garantiinformasjon og teknisk støtte, se den offisielle Alpine-håndboken website or contact Alpine customer service directly. Keep your proof of purchase for warranty claims.

Alpine Customer Support: Refer to your product packaging or the official Alpine webnettstedet for den mest oppdaterte kontaktinformasjonen.