OUXI V8 Elektrische Fiets Gebruikershandleiding

Montage-instructies

This section provides detailed instructions for assembling your OUXI V8 Electric Bike. Please follow the steps carefully to ensure proper setup and safe operation.

Stapsgewijze montage:

1. Product Unpacking: First, cut the outer packing. Remove all included accessories from the box.
2. Remove Buffer Foam: Carefully remove all buffer foam protecting the bike. Take out the main body of the electric bike. Remove all cable ties securing components. The battery key is located on the left side of the rear wheel.
3. Montage op het stuur: Remove the larger allen wrench from the kit. Loosen the two side screws on the handlebar connection. Remove the top screws and detach the handlebar connection. Loosen the screws on both sides of the shock absorber barrel. Run the handlebar wire around the shock absorber barrel. Put the iron blocks and rings back in place and tighten the screws. Insert the dust plug into the shock absorber barrel. Install the handlebar connection bar facing up. Tighten the screws on the side of the top screw box. Adjust the handlebars to a proper angle and use a wrench to secure the screws.
4. Front Wheel Mounting: Loosen the screws on both sides of the front wheel. Insert your forearm into the front wheel bearing. Turn the strip and tighten the screws. Then tighten the screw with the No.15 wrench. Insert the screw caps into both sides.
5. Foot Mounting: Take out your foot in the right direction. Rotate the pedal screw position to hold it in place. Tighten the pedal with a 15-gauge wrench. Notice that the thread on the other foot is reversed; the operation is the same.
6. Front Fender Mounting: Knip de tape van het voorspatbord af. Verwijder de moer met een sleutel nr. 10. Plaats het spatbord terug en draai de schroeven vast. Verwijder de schroeven aan beide kanten. Plaats de spatbordbeugel terug. Draai vast met een grote inbussleutel. Doe hetzelfde aan de andere kant.
7. Rear Seat Mounting: Remove a pair of screws. Insert the screw into the joint of the seat bracket and twist the screws. Use two more wrenches to tighten the screws. Do the same on the other side. Take out the number eight wrench. Remove the two screws from the taillight. Insert the rear seat into the mounting hole of the frame. Tighten all screws. Put the taillights in the rear seat. Then install the original two screws and tighten it with an 8-gauge wrench. Use cable ties to secure the wires. Cut off any extra cable ties with scissors.
8. Aerating the Wheel: Take out the pump. Put proper tire pressure on the front and rear wheels.
9. Meter Adjustment: Pak de kleine inbussleutel. Draai de twee schroeven los waarmee de meter vastzit. Draai de schroeven weer vast nadat de meter in de juiste hoek is gezet.
10. Batterij opladen: Open het accuslot met de sleutel. Duw omhoog om de accu te verwijderen. Sluit de lader aan op de accu en schakel het apparaat in. Laad de accu volledig op. Plaats de volle accu in de accuhouder en vergrendel deze. Schakel de accu in.

Operating Your OUXI V8 Electric Bike

The OUXI V8 Electric Bike is designed for versatile riding experiences. Understand its modes and display to maximize your ride.

Rijmodi

• Puur elektrische modus: Utilizes the throttle for propulsion without requiring pedaling.
• Trapondersteuningsmodus: Provides motor assistance while you pedal, offering an easier ride.
• Pedaalmodus: Functions as a traditional bicycle with no motor assistance.

The OUXI V8 offers three versatile riding modes: Bike Mode (power off, normal pedaling), Assisted Riding (power on without throttle), and Pure Electric Mode (throttle only, no pedaling required).

Weergavefuncties

The M5 large LCD display provides essential information for your ride:

• Batterij: Geeft het huidige batterijlaadniveau weer.
• Energiereep: Visual representation of power consumption.
• Snelheid: Geeft de huidige rijsnelheid weer.
• Loop: Indicates walk assist mode.
• PAS: Pedal Assist System level indicator.
• Kilometerteller: Houdt de totale afgelegde afstand bij.
• hoofdlamps: Indicator for activated headlights.
• Gear Position: Shows the current gear selected.
• Cruisecontrol: Geeft aan of cruise control actief is.

The M5 large LCD display provides essential information such as battery level, speed, gear position, odometer, and indicators for headlamps and cruise control. Handlebar controls allow for speed adjustment and gear changes.

Batterijgebruik

The OUXI V8 e-bike is equipped with a 48V 15AH removable battery. This battery provides a riding range of up to 37 miles on a full charge. A full charge typically takes 7-8 hours. The removable design allows for convenient charging off the bike.

The removable 48V 15Ah lithium battery provides a riding range of 28-37 miles and charges in 5-7 hours. It is IP54 waterproof for durability.

Onderhoudsrichtlijnen

Regular maintenance is crucial for the longevity and safe operation of your OUXI V8 Electric Bike. Perform these checks periodically:

• Bandenspanning: Ensure tires are inflated to the recommended pressure before each ride.
• Remmen: Regularly check brake pads and cables for wear and proper function. Adjust as needed.
• Ketting: Houd de ketting schoon en gesmeerd om ervoor te zorgen dat de versnellingen soepel verlopen en om roest te voorkomen.
• batterij zorg: Store the battery in a cool, dry place. Avoid fully discharging the battery frequently. Charge regularly, even when not in use for extended periods.
• Bevestigingsmiddelen: Periodically check all nuts and bolts for tightness, especially after the first few rides.
• Algemene schoonmaak: Maak de fiets regelmatig schoon met adamp doek. Vermijd het direct met hogedrukspuiten van elektrische componenten.

The OUXI V8 Electric Bike features a robust frame, 20-inch fat tires, and integrated lighting. Its design combines classic aesthetics with modern electric bike functionality.

Problemen met veelvoorkomende problemen oplossen

If you encounter any issues with your OUXI V8 Electric Bike, please refer to the following common troubleshooting tips. For more complex problems, contact customer support.

• Bike Not Turning On: Check if the battery is properly seated and locked. Ensure the battery is charged. Verify the power button on the battery is turned on.
• Motor ondersteunt niet: Confirm you are in pedal-assist or pure electric mode. Check if the throttle or pedal-assist sensor is obstructed or damaged. Ensure the battery has sufficient charge.
• Piepende remmen: This can often be resolved by cleaning the brake rotors and pads. If the issue persists, brake pads may need replacement or adjustment.
• Moeite met schakelen: Check for proper chain lubrication. Inspect the derailleur and shifter cables for damage or misalignment.

Veelgestelde vragen

• How to Assemble the Electric Bikes? Please check the assemble video on the product page or refer to the 'Assembly Instructions' section in this manual.
• How to get help from the seller? Please click “Contact Seller” on your order. We have professional technicians at your service and we are willing to help you solve your problem!

Productspecificaties

Afmetingen en gewicht

Key dimensions include a total length of 66.14 inches, total height of 45.66 inches, and a wheelbase of 40.47 inches. The bike weighs 83.77 lbs (38 KG) and has a maximum load capacity of 330 lbs. Recommended rider height is 5'4"-6'5".

Garantie en klantenondersteuning

OUXI provides comprehensive support for your V8 Electric Bike:

• Garantie: The OUXI V8 Electric Bike comes with a 1-year manufacturer's warranty. The frame has a lifetime warranty.
• Klantenservice: For any inquiries or assistance, please contact OUXI customer support through Amazon. We offer 24-hour service to help resolve any issues you may encounter with your e-bike.