E-flite Carbon-Z Cessna 150 2.1M BNF Basis RC Vliegtuig Gebruiksaanwijzing

1. Product voorbijview

The E-flite Carbon-Z Cessna 150 2.1M BNF Basic is a large-scale remote control aircraft designed for sport flying. This model offers a wide flight envelope, suitable for various flying styles. It incorporates scale details and features for an enhanced experience.

Belangrijkste kenmerken:

• Large sport-scale model suitable for diverse flight maneuvers.
• Wide flight envelope, accommodating both gentle and aggressive flying.
• Scale details including LED lights, functional flaps, and wheel pants.
• Designed for field assembly without requiring tools.
• Innovative hands-free servo connection system for simplified setup.

Figuur 1.1: Voorzijde view of the E-flite Carbon-Z Cessna 150 2.1M RC Airplane.

2. Veiligheidsinformatie

WAARSCHUWING: Lees de HELE gebruiksaanwijzing om vertrouwd te raken met de functies van het product voordat u het gebruikt. Als u het product niet correct bedient, kan dit leiden tot schade aan het product, persoonlijke eigendommen en ernstig letsel. Dit is een geavanceerd hobbyproduct. Het moet met voorzichtigheid en gezond verstand worden bediend en vereist enige basismechanische vaardigheden. Als u dit product niet op een veilige en verantwoorde manier bedient, kan dit leiden tot letsel of schade aan het product of andere eigendommen. Dit product is niet bedoeld voor gebruik door kinderen zonder direct toezicht van een volwassene. Gebruik het niet met incompatibele componenten en wijzig dit product op geen enkele manier buiten de instructies van Horizon Hobby, LLC. Deze handleiding bevat instructies voor veiligheid, bediening en onderhoud. Het is essentieel om alle instructies en waarschuwingen in de handleiding te lezen en op te volgen, voorafgaand aan de montage, installatie of het gebruik, om correct te kunnen werken en schade of ernstig letsel te voorkomen.

3. Wat zit er in de doos?

• Carbon-Z Cessna 150 BNF Basic RC Airplane

Note: Additional components such as a compatible Spektrum DSMX/DSM2 transmitter, flight battery, and charger are required and sold separately.

4. Opstelling en montage

4.1 Wing Assembly

1. Carefully slide each wing panel onto the wing tube until it is fully seated against the fuselage.
2. Ensure the hands-free servo connections engage properly.
3. Secure each wing panel using the provided fasteners or pins, as indicated in the manual.

Figure 4.1: Detail of component assembly, showing a pin being inserted.

4.2 Landing Gear Installation

Attach the main landing gear and tail wheel assembly according to the diagrams. Ensure all connections are secure. The model features wheel pants for scale appearance.

4.3 Servo Connections

The Carbon-Z Cessna 150 utilizes an innovative hands-free servo connection system. When assembling the wings, ensure the servo connectors align and engage automatically. Verify all control surfaces move freely and correctly after assembly.

Figure 4.2: Detail of the hands-free servo connection system.

4.4 Battery Installation and Binding

1. Install the recommended flight battery (sold separately) into the designated battery compartment. Secure it to prevent movement during flight.
2. Follow the instructions for your Spektrum DSMX/DSM2 compatible transmitter to bind it with the aircraft's receiver. Refer to your transmitter's manual for specific binding procedures.
3. After binding, perform a control surface test to ensure all controls (ailerons, elevator, rudder, throttle) respond correctly to transmitter inputs.

5. Gebruiksaanwijzing

5.1 Controles vóór de vlucht

• Ensure the flight battery is fully charged and securely installed.
• Verify all control surfaces move freely and in the correct direction relative to transmitter inputs.
• Check propeller for any damage or looseness.
• Confirm the transmitter battery is adequately charged.
• Perform a range check of your radio system before the first flight of the day.

5.2 Opstijgen

Place the aircraft on a smooth surface facing into the wind. Gradually advance the throttle. Apply slight up-elevator as speed increases to lift off. Maintain a steady climb rate.

5.3 Vlucht

The Carbon-Z Cessna 150 is designed for stable flight characteristics. Use the ailerons for roll control, elevator for pitch, and rudder for yaw. Adjust throttle to control speed. Utilize flaps for slower flight and improved lift during takeoff and landing, if desired.

Figure 5.1: The Carbon-Z Cessna 150 in stable flight.

5.4 Overloop

Approach the landing strip into the wind. Reduce throttle and gradually deploy flaps if using them. Maintain sufficient airspeed for control. Flare gently by applying up-elevator just before touchdown to achieve a smooth landing.

6. Onderhoud

6.1 Inspectie na de vlucht

• Inspect the airframe for any damage, cracks, or loose components.
• Check all control linkages and hinges for wear or looseness.
• Examine the propeller and spinner for damage. Replace if necessary.
• Ensure landing gear is secure and undamaged.

6.2 Reiniging en opslag

Reinig het vliegtuig met een zachte, droge doek.amp cloth. Avoid using harsh chemicals. Store the model in a cool, dry place, away from direct sunlight and extreme temperatures, to preserve its materials and electronics.

7. Probleemoplossing

8. Specificaties

Figure 8.1: The Carbon-Z Cessna 150 demonstrating its substantial size.

9. Garantie-informatie

This product is covered by a limited warranty provided by Horizon Hobby, LLC. For detailed warranty terms and conditions, please refer to the official Horizon Hobby webBezoek de website of neem contact op met hun klantenservice. Een aankoopbewijs kan vereist zijn voor garantieclaims.

10. Klantenservice

For technical assistance, spare parts, or further information regarding your E-flite Carbon-Z Cessna 150, please visit the official E-flite or Horizon Hobby website. You can also contact their customer service department directly for support.

E-flite Store: Visit the E-flite Store on Amazon