Exercise care when handling sharp blades during emptying and
cleaning.
Do not attempt to sharpen blades; contact SharkNinja for
replacements if needed.

Use the blender on a dry and level surface at all times.

FAQ

Q: Can I use attachments not provided with the product?

A: It is recommended to only use attachments and accessories
provided with the product or those recommended by SharkNinja to
ensure safe operation.

Q: What should I do if a blade is damaged?

A: If you suspect blade damage, contact SharkNinja for a
replacement. Do not attempt to sharpen the blades.

“`

View Fullscreen

ENGLISH

BLASTTM PORTABLE BLENDER BC151SM Series | Owner’s Guide
IMPORTANT SAFETY INSTRUCTIONS
PLEASE READ ALL INSTRUCTIONS BEFORE USE · FOR HOUSEHOLD USE ONLY
Read and review instructions for operation and use.
Indicates the presence of a hazard that can cause personal injury, death or substantial property damage if the warning included with this symbol is ignored.
For household use only.
Indicates location to attach USB-C cord for charging unit.
When using electrical appliances, basic safety precautions should always be followed, including the following:
WARNING: To reduce the risk of injury, fire, electrical shock or property damage, basic safety precautions must always be followed,
including the following numbered warnings and subsequent instructions. Do not use appliance for other than intended use.
1 Read all instructions prior to using the appliance and its accessories. 2 Use only a power supply with an extra low voltage corresponding to the marking on the bottom of the motor base. 3 ALWAYS exercise care when handling the BlastBlade Assembly. The blades are sharp, handle carefully. ONLY grasp the BlastBlade Assembly
by the motor base. Failure to use care when handling the BlastBlade Assembly will result in a risk of laceration. 4 Take your time and exercise care during unpacking and appliance setup. This appliance contains sharp blades that can cause injury
if mishandled. 5 Take inventory of all contents to ensure you have all parts needed to properly and safely operate your appliance. 6 Before use, wash all parts that may contact food. Follow washing instructions covered in this Owner’s Guide. 7 DO NOT blend hot liquids, effervescent, or carbonated liquids, as doing so may cause pressure buildup, resulting in risk of burns or other
injuries to the user. 8 DO NOT fill the blending vessel past the MAX FILL line. 9 Blades are sharp. Handle carefully. Care shall be taken when handling the sharp cutting blades, emptying the vessel, and during cleaning. 10 Keep hands, hair, and clothing out of the vessel when loading and operating. DO NOT put your hands inside the vessel or anywhere near
the BlastBlade Assembly. Blades can still activate when the sip lid is removed. 11 Before operation, ensure all utensils are removed from containers. Failure to remove utensils can cause the vessel to shatter and potentially
result in personal injury and property damage. 12 To protect against the risk of fire from battery damage, DO NOT submerge the motor base in any form of liquid. 13 DO NOT store outdoors or allow the product to be submerged in liquid. 14 DO NOT allow children to operate this appliance or use as a toy. Close supervision is necessary when any appliance is used near children. 15 This appliance is NOT intended to be used by people with reduced physical, sensory, or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. 16 Before each use, inspect BlastBlade Assembly for damage. If a blade is bent or damage is suspected, contact SharkNinja to arrange
for replacement. 17 DO NOT attempt to sharpen blades. 18 DO NOT allow any part of the unit to contact hot surfaces, including stoves and other heating appliances. 19 ALWAYS use the appliance on a dry and level surface.
SG sharkninja.sg | MY sharkninja.my

IMPORTANT SAFETY INSTRUCTIONS
PLEASE READ ALL INSTRUCTIONS BEFORE USE · FOR HOUSEHOLD USE ONLY
20 Keep hands, hair, and clothing out of the vessel when loading and operating. 21 ONLY use attachments and accessories that are provided with the product or are recommended by SharkNinja. The use of attachments not
recommended or sold by SharkNinja may cause fire, electric shock, or injury. 22 During operation and handling of the appliance, avoid contact with moving parts. 23 DO NOT operate the appliance with an empty container. 24 DO NOT microwave any containers or accessories provided with the appliance. 25 DO NOT perform grinding operations. 26 DO NOT attempt to defeat the interlock mechanism. Ensure the vessel and sip lid are properly installed before operation. 27 DO NOT expose the containers and accessories to extreme temperature changes. They may experience damage. 28 NEVER leave the appliance unattended while in use. 29 If you find unmixed ingredients sticking to the sides of the cup, turn off the appliance using the Power button, and use a scraper to
dislodge ingredients. 30 DO NOT attempt to remove the vessel and/or sip lid from the motor base while the BlastBlade Assembly is still spinning. Allow the appliance
to come to a complete stop before removing lid and/or vessel. 31 DO NOT store ingredients for extended amounts of time before or after blending them. Some foods may contain active ingredients or release
gases that will expand if left in a sealed container, resulting in excessive pressure buildup that can pose a risk of injury. 32 If the appliance overheats, a thermal switch will activate and temporarily disable the motor. To reset, turn OFF the Ninja BlastTM Portable Blender
using the Power button and allow it to cool for approximately 15 minutes before using again. 33 DO NOT process dry ingredients without adding liquid to the blending vessel. Unit is not intended for dry blending. 34 Operate ONLY with the sip lid on. 35 DO NOT refrigerate or freeze blender. 36 DO NOT misuse the appliance to avoid potential injury.
BATTERY USE
1 The battery is the power source for the Ninja BlastTM Portable Blender. Carefully read and follow all charging instructions. 2 DO NOT incinerate this appliance even if it is severely damaged. The lithium-ion batteries can explode in a fire. Always properly recycle
products powered by lithium-ion batteries. 3 Since there is no power cord, prevent accidental blade activation by ensuring the blender is turned OFF when not in use, while cleaning,
or when drinking from the sip lid. 4 Keep the battery away from all metal objects such as paper clips, coins, keys, nails, or screws. Shorting the battery terminals together
increases the risk of fire or burns. 5 Under abusive conditions, liquid may be ejected from the battery. Avoid contact with this liquid, as it may cause irritation or burns. If contact
occurs, flush with water. If liquid contacts eyes, seek medical help. 6 This unit contains batteries that are only replaceable by skilled persons. 7 This unit contains batteries that are non-replaceable and moving parts that potentially present risk to the user.
SAVE THESE INSTRUCTIONS
SG sharkninja.sg | MY sharkninja.my

PARTS

A Sip Lid

B Carry Handle

C Blending Vessel*

D Vessel Cap*

E Blade Cover*

F Motor Base with

BlastBlade Assembly

G USB-C Charging Cord

H Charging Port

D
*Blending vessel sizes and quantity, and accessories, vary by model.
E G

F H

CHARGING

Motor Base Back

Charge the unit using the provided charging cord and a 5V 3A power supply until the LEDs illuminate solid green. Charging port is located at the back of the motor base.

BEFORE FIRST USE
IMPORTANT: Review all warnings at the beginning of this Owner’s Guide before proceeding.
NOTES: · Handle the BlastBlade Assembly by grasping around the motor base. · All attachments are BPA free. All attachments EXCEPT the motor base are top-rack dishwasher
safe. DO NOT use a heated dry cycle. Ensure lid and vessel are removed from motor base before placing in the dishwasher. Exercise care when handling BlastBlade Assembly.
Remove all packaging materials from the unit. Exercise care when unpacking BlastBlade Assembly, as the blade are sharp. To clean the vessel and lid, add warm water up to MIN LIQUID line, then add 1 small drop of dish soap. Securely attach the lid and blend. Empty contents and rinse again with warm water. DO NOT submerge the motor base in water when cleaning. Exercise care when handling BlastBlade Assembly, as the blades are sharp. Thoroughly rinse and air-dry all appropriate parts.
SG sharkninja.sg | MY sharkninja.my

ENGLISH

USING THE CONTROL PANEL
PROGRAMS: START/STOP BUTTON Press Start/Stop button once to activate the 30-second blend cycle.
POWER BUTTON Press Power button to turn unit ON and OFF.

LED Shows Flashing WHITE
Flashing ORANGE Solid RED Flashing RED and BLUE Clockwise-moving ORANGE LEDs Flashing WHITE and RED Flashing RED in the bottom left and top right

TROUBLESHOOTING Vessel and Base are Not Aligned Blades are Blocked Needs Charge Abnormal Charger Unit Cool Down Time Out While Charging While Blending

Solutions Ensure vessel and motor base are aligned using the arrows on the back of motor base and vessel. Move lodged ingredients from blade and restart blend program.
Charge unit.
Defective or incorrect charger; unplug and find correct 5V 3A charger. Let unit sit at room temp for 15 minutes before using again.
Contact Customer Service.
Contact Customer Service.

USING THE BLENDING VESSEL
IMPORTANT: Review all warnings at the beginning of this Owner’s Guide before proceeding.
1 Ensure the motor base is fully charged and the vessel is properly installed by aligning vessel arrow with motor base arrow located on the back of the motor base.

2 Turn unit ON by pressing the button until Start/Stop button lights illuminate.
3 Add ingredients, starting with liquids to the MIN LIQUID line then solid ingredients. If using ice, always add last. DO NOT fill ingredients past the MAX FILL line. Secure lid onto the vessel, twisting clockwise to tighten.
4 Blend for a 30-second blend cycle by pressing the Start/Stop button.

SG sharkninja.sg | MY sharkninja.my

5 Open the sip lid to sip, or remove the lid to pour out blender outputs into another container. DO NOT remove vessel from motor base when filled. Empty vessel prior to removing from motor base.
6 After blending, power OFF the unit by pressing the button. Motor base should be turned OFF when drinking from the sip lid and when blender is no longer in use.
7 After blending is complete, ensure the lid is on tight and turn the blender upside down.
8 Twist motor base counterclockwise to remove it from the vessel, and set the motor base right side up.
9 Install the vessel cap on the bottom of the vessel by turning it clockwise. Install the blade cover on the motor base to cover the exposed blades by turning it clockwise.
10 Refer to the Care & Maintenance section for cleaning and storage instructions.
CARE & MAINTENANCE
CLEANING
Blades can still operate when the lid is removed. Always turn the unit OFF when cleaning without the lid on or when the BlastBlade Assembly is exposed. Quick Clean To clean, add warm water up to MIN LIQUID line, then add 1 small drop of dish soap. Securely attach the lid and blend. Empty contents and rinse again with warm water. Hand-Washing Wash vessel and lid with warm, soapy water. Use a dishwashing utensil or cloth to clean the BlastBlade Assembly on the motor base. Exercise care when handling the BlastBlade Assembly on the motor base as the blades are sharp. Wipe the motor base with a clean, damp cloth. DO NOT submerge the motor base in water. Thoroughly rinse and air-dry all appropriate parts. Motor Base Motor base is NOT dishwasher safe and can not be submerge in water. Use a long stemmed cleaning brush to clean the blades. DO NOT put the motor base in the dishwasher or submerge it in water. Ensure the USB-C charger is not inserted before cleaning. After cleaning, let the USB-C charging port air-dry for 30 minutes before charging the unit.
DEEPER CLEAN
Dishwasher Vessel and sip lid are top-rack dishwasher safe. DO NOT use a heated dry cycle. Ensure the vessel and sip lid are removed from the motor base before being placed in the dishwasher.
STORING
Store the unit upright and with the lid, vessel, and motor base fully assembled. DO NOT store blended or unblended ingredients in the vessel with the BlastBlade Assembly for prolonged periods of time. DO NOT stack items on top of the vessel. Store any remaining attachments alongside the unit or in a cabinet where they will not be damaged or create a hazard. If your unit needs servicing, contact Customer Service at SG sharkninja.sg or MY sharkninja.my. So we may better assist you, please register your product online at the links above and have the product on hand when you contact us.
SG sharkninja.sg | MY sharkninja.my

ENGLISH

TROUBLESHOOTING GUIDE
WARNING: To reduce the risk of shock and unintended operation, turn OFF unit before
troubleshooting. Ensure the unit is not charging when troubleshooting. Ensure the unit is fully charged and vessel is properly aligned. Control panel doesn’t turn off. · Press the button to turn the unit ON and OFF. Doesn’t mix well; ingredients get stuck. · When filling the vessel, start with liquid to the MIN LIQUID line, then fresh fruit or veggies, followed by leafy greens or herbs.
Add your seeds, powders, or nut butters. Finish with ice or frozen ingredients. · If ingredients are routinely getting stuck, adding some liquid will usually help. Ensure you have filled the vessel to or
above the MIN LIQUID line. You can also shake the blender while blending, or turn the blender upside down, start a blend cycle, and turn it right side up, to move ingredients while blending. Sip lid is hard to assemble on the vessel. · Set the assembled motor base and vessel on a level surface. Place the sip lid on the top of the vessel and align the threads so the sip lid sits flat. Turn clockwise until you have a tight seal. Vessel is hard to assemble on the motor base. · Set the motor base on a level surface. Place the vessel on the top of the motor base and align the threads so the vessel sits flat. Turn clockwise until you have a tight seal. When the vessel is properly installed, the LEDs on the display will be solid purple or solid yellow, depending on the battery level.
PRODUCT REGISTRATION
Please visit sharkninja.sg/apps/product-registration to register your new Ninja product within ten (10) days of purchase. You will be asked to provide the store name, date of purchase, and model number along with your name and address.
The registration will enable us to contact you in the unlikely event of a product safety notification. By registering, you acknowledge you have read and understood the instructions for use and warnings set forth in the accompanying instructions.
ORDERING REPLACEMENT PARTS
To order additional parts and attachments, contact SG customerservice.sg@sharkninja-apac.com or MY customerservice.my@sharkninja-apac.com.

ONE (1) YEAR LIMITED REPLACEMENT WARRANTY
The warranty commences on the date of purchase and expires at the end of the 1 year period. In the unlikely event of a defect due to faulty materials or workmanship within the guarantee period we will replace the defective/faulty part with a new product, free of charge, or if the unit is deemed defective/faulty we replace the unit with an equivalent or upgraded model, at our discretion. For warranty claims, you will need to submit a proof of purchase in the form of a valid receipt that displays date and place of purchase. Replacement items will be covered by the limited warranty for the balance of the warranty period from the date of the original purchase. Please note:
Your warranty is subject to the following conditions: · DO NOT operate the appliance with a damaged plug or cord, or if the unit has been dropped,
damaged or dropped in water. · To avoid the risk of electric shock, do not disassemble or attempt to repair the appliance on
your own. If the supply cord is damaged, it must be replaced by a qualified electrician to avoid a hazard. Incorrect re-assembly or repair can cause a risk of electric shock or injury to persons when the appliance is used. · The item has not been misused, abused, neglected, altered, modified or repaired by anyone. · The item has been subjected to fair wear and tear. · The item has not been used for trade, professional or hire purposes. · The item has not sustained damage through foreign objects, substances or accident · Accidental damage · Damage as a result of use not in accordance with the rating plate · Use of parts and accessories that are not genuine Ninja components
Customer costs within warranty · The customer is responsible for any inwards freight charge to return a product for warranty if
requested, and outward freight charge for warranty parts and or replacement unit.
Who is covered? · This warranty applies only to the original purchaser, who bought the product from an
authorised retailer and may not be transferred. Proof of purchase is required.
What is not covered? · Accessories supplied with the item. · Components that are subject to natural wear and tear caused by normal use in accordance
with operating instructions. · Unauthorised/improper maintenance/handling or overload is excluded from this warranty.

SG sharkninja.sg | MY sharkninja.my

REGISTER YOUR PURCHASE SG sharkninja.sg/apps/product-registration MY sharkninja.my/apps/product-registration
SG Ninja Kitchen Chefs MY Ninja Kitchen Chefs (MY)

SG @ninjakitchensg | MY @ninjakitchenmy

RECORD THIS INFORMATION Model Number: ____________________ Serial Number: _____________________ Date of Purchase: ___________________ (Keep receipt) Store of Purchase: __________________

TECHNICAL SPECIFICATIONS

Voltage:

5V , 0.5A3A

SharkNinja Singapore Pte. Ltd. United Square Office Tower 101 Thomson Road #27-01 to 03 Singapore 307591 customerservice.sg@sharkninja-apac.com
23-8, Menara Permata Damansara No. 685 Jalan Damansara 60000 Kuala Lumpur Wilayah Persekutuan, Malaysia customerservice.my@sharkninja-apac.com
Illustrations may differ from actual product. We are constantly striving to improve our products; therefore the specifications contained herein are subject to change without notice.
NINJA BLAST is a trademark of SharkNinja Operating LLC.
© 2024 SharkNinja Operating LLC
BC151SMSeries_IB_MP_Mv6

Documents / Resources

NINJA BC151SM Series Blast Portable Blender [pdf] Owner's Manual
BC151, BC151SM, BC151SM Series Blast Portable Blender, BC151SM Series, Blast Portable Blender, Portable Blender, Blender

References

User Manual

NINJA BC151SM Series Blast Portable Blender Owner’s Manual

BC151SM Series Blast Portable Blender

Product Information

Specifications

Product Usage Instructions

Safety Precautions

Setup and Assembly

Blending Instructions

Cleaning and Maintenance

FAQ

Q: Can I use attachments not provided with the product?

Q: What should I do if a blade is damaged?

Documents / Resources

References

Leave a comment

Cancel reply