UHRT08C Remote Transmitter
“
Product Information
Specifications:
- Model No.: UHRT08C (JHT2204B)
- Transmission Frequency: 434MHz
- Transmitter: DC 12V (23A) battery 1pc
- Working temperature: -20 to +55°C
Product Usage Instructions
Installation and Battery Change:
1. Open the battery compartment located on the back of the
remote control.
2. Install one (1) x 12V (23A) battery in the compartment,
ensuring the correct orientation of the positive and negative
electrodes.
Operation:
The remote control features two buttons for individual ON and
OFF functions.
Usage Details:
The transmitter must be paired with corresponding radio
receivers to operate. It can control receivers such as sockets,
light bulb sockets, switch kits, etc., within approximately 100ft
distance.
Troubleshooting:
– If the remote control distance decreases or the indicator
weakens, replace the battery promptly.
– Ensure correct battery installation if the remote control is
unresponsive or the indicator does not light up when pressing
buttons.
– Regularly replace the battery for optimal performance.
FAQ
Q: Can the transmitter be used separately without a
corresponding receiver?
A: The transmitter can be sold separately but requires matching
with compatible radio receivers to function.
Q: What should I do if the remote control is not
responsive?
A: Check the battery installation for correct polarity and
replace the battery if needed. Consult a professional if issues
persist.
“`
Instruction Manual for Remote Transmitter
Model No.: UHRT08C (JHT2204B)
INSTALLATION AND CHANGE THE BATTERY:
Open the battery compartment which on the back of remote control, Install one (1) x 12V (23A) battery in the compartment, make sure the positive and negative electrodes of battery is correct.
OPERATION:
There are two buttons on remote control for individual ON and OFF function.
TECHNICAL DATA:
Transmission Frequency: 434MHz Transmitter : DC 12V (23A) battery 1pc Working temperature: -20 to + 55
Other Details:
The transmitter can be sold separately, but can not be used separately, it will have to be matched corresponding radio receivers to use. The transmitter can only turn ON or OFF the corresponding receivers individually on about 100ft distance. The corresponding receivers such as socket, light bulb socket, switch kit, etc.
Troubleshooting:
If you find the remote control distance becomes short or the indicator on remote transmitter becomes weak, then please replace the battery with fresh battery asap. Please check if the positive and negative of the battery installation is correct if the remote control is no response or the indicator on remote control is not on when press any one of the key buttons. Regular change fresh battery for best use.
Federal Communications Commission Interference Statement Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. – Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected. – Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
ISED Warning:
This device complies with Innovation, Science, and Economic Development Canad licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’ Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil nedoit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. The device is compliance with RF exposure guidelines, users can obtain Canadian information on RF exposure and compliance. Le présent appareil est conforme Après examen de ce matériel aux conformité ou aux limites d’intensité de champ RF,les utilisateurs peuvent sur l’exposition aux radiofréquences et la conformité and compliance d’acquérir les informations correspondantes.
Documents / Resources
 |
NINGBO UHRT08C Remote Transmitter [pdf] Instruction Manual UHRT08C, UHRT08C Remote Transmitter, Remote Transmitter, Transmitter |