ningbo Electric Winch Wireless Controller Instructions

ningbo-LOGO

ningbo Electric Winch Wireless Controller

ningbo-Electric-Winch-Wireless-Controller-PRODUCT

Features Overview

This wireless remote control firing frequency of 314-316MHz, the control range of more than 20 meters, used in electric winch wireless control.

The wireless remote control parameters

  1. Working voltage: DC3V, 2 pcs CR2032 battery.
  2. The working current: 35mA ± 5mA
  3. Transmitting frequency: 314-316MHz
  4. The transmit power: <10dBm
  5. Standby current: <5uA

Using

The remote controller have 3 keys. Press and hold the ”ON/OFF” button more than 3 seconds, the remote powered on, while the LED indicator lights. Then press the key of “Extend” or “Retract”, it will trigger 315 MHz high-frequency FSK modulation unit to transmit the address code and key value. The high-frequency signal emitted by the antenna. When the remote control has been powered on, press and hold the ”ON/OFF” button more than 3 seconds, the remote control is turned off, while LED is off. If there is no key operation within 50 seconds, it will automatically shut down.

Installation and function

  1. Disconnect Power to the winch
  2. Confirm that the plug is the correct type for this winch and plug it in
  3. Select an area for the receiver on the vehicle close enough to the winch to allow cable connection
  4. Investigate the chosen area to make sure no components will be damaged by installation.
  5. Permanently (optional) mount the remote control receiver to the vehicle using appropriate hardware (not included).
  6. Preare the winch for operation as explained in its manual
  7. Reconnect winch’s power
  8. Release the clutch handle and pull out about 10 feet of wire rope Leave the wire rope laying on the ground and stay clear of the wire rope and hook
  9. Reengage the clutch handle
  10. Watch the spool and wire rope and briefly, press the “Extend” button on the remote control to verify that the cable feeds out
    WARNING! If the cable does not feed out, check and correct the winch’s wiring. Retest after correction.
  11. Watch the spool and wire rope and briefly press the “Retract” button on the remote control to verify that the cable retracts
    WARNING! If the cable does not feed out, check and correct the winch’s wiring. Retest BOTH functions after correction.
  12. If the remote operates the winch properly, it is ready for use.
  13. After use, disconnect control box from winch to prevent accidental operation

Wiring diagram

ningbo-Electric-Winch-Wireless-Controller-FIG-1

WARNING

To prevent serious injury

  1. Disconnect control box from winch before service and after every use.
    WINCH CAN OPERATE SUDDENLY AT ANY TIME WHILE CONNECTED.
  2. Stand clear of winch, fairlead, and wire rope while connected. Keep bystanders away.
  3. Only operate controls when winch and entire wire rope is within view.
  4. Use with vehicle mounted recovery winches only. Do not use for any other application.
  5. Confirm control box mounting location has no wire or components that can be damaged drilling.
  6. Read winch manual before use.

FCC STATEMENT

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC warning:
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Documents / Resources

PDF thumbnailElectric Winch Wireless Controller
Instructions · SM-SRC, SMSRC, 2AM3B-SM-SRC, 2AM3BSMSRC, Electric Winch Wireless Controller, Winch Wireless Controller, Wireless Controller, Controller
PDF thumbnailElectric Winch Wireless Controller
Instructions · CM-SMT, CMSMT, 2AM3B-CM-SMT, 2AM3BCMSMT, Electric Winch Wireless Controller, Electric Winch Controller, Winch Wireless Controller, Winch Controller, Winch Electric Controller

References

Questions and answers

Helpful product questions tied to this manual. Each item links to the full Q&A page.

Browse all questions about this manual

Questions & Answers

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

  1. Is a remote available and if so cost?

    Gary asks Is a remote available and if so cost?
    Manuals+ clarified question
    Question

    Is a replacement remote available for the Ningbo Electric Winch Wireless Controller and what is the cost?

    Answer

    Manuals+ provides technical documentation and instructions for products but does not directly sell replacement parts or hardware. The provided manual for the Ningbo Electric Winch Wireless Controller does not list specific retail pricing or a direct parts ordering catalog.

    To find a replacement remote, you should check with the original retailer where the winch was purchased or search for a 314-316MHz frequency wireless winch remote, as this is the transmitting frequency specified in the technical parameters of the manual. The remote typically uses two CR2032 batteries.

    If you are looking for the receiver unit as well, ensure it is compatible with a DC10-15V working voltage as noted in the receiver specifications.

Ask a Question

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.