Nicolas Holiday Remote Controller Instruction Manual

Nicolas Holiday Remote Controller logo

Nicolas Holiday Remote Controller

Nicolas Holiday Remote Controller product

MODES

The power On/Off functions and lighting  modes can  be controlled with either the remote  control or  the foot foot pedal.
Nicolas Holiday Remote Controller 01Remote Control
Three static lighting modes : Soft White, Day Light, Bright White. Brightness adjustment and color temperature adjustment by remote Control only. Long pressing of +/- will achieve color temperature and brightness you want.
Twinkling Mode
Two twinkling lighting modes : Soft White Twinkling and Bright White Twinkl ing.
Fade/Flash Mode
Two fade lighting modes : Soft White slowly transitions to Bright White And Twinkle Flashing.
Night light Mode
One lighting mode: functions as a night light effect.
Timer Mode
Pressing will activate lighting timer for 5 hours. At the end of 5 hours. The lights automatically turn off. The lights will automatically turn on the next evening at the same time,Nicolas Holiday Remote Controller 02

FCC

Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:

  1. this device may not cause harmful interference, and
  2. this device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
  • This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
  • This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Documents / Resources

PDF thumbnailRemote Controller
Instruction Manual · T09CX, 2A922-T09CX, 2A922T09CX, Remote Controller, Remote, Controller

References

Questions and answers

Helpful product questions tied to this manual. Each item links to the full Q&A page.

Browse all questions about this manual

Questions & Answers

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

  1. I purchased Trim-A-Tree model 23142LO from Lowes several years ago. It has worked well until recently. The date code is FP0323. It currently seems to have a loose connection somewhere. The lights on the tree will sometimes light completely for a few seconds and then go completely dark. I have replaced the transformer; but this did not solve the problem. A voltage test indicates that power is available everywhere I have checked on the light strand.

    Do you have any suggestions on how to diagnose and repair the lights?

    🇺🇸 Stanley Legm asks I purchased Trim-A-Tree model 23142LO from Lowes several years ago. It has worked well until recently. The date code is FP0323. It currently seems to have a loose connection somewhere. The lights on the tree will sometimes light completely for a few seconds and then go completely dark. I have replaced the transformer; but this did not solve the problem. A voltage test indicates that power is available everywhere I have checked on the light strand.

    Do you have any suggestions on how to diagnose and repair the lights?

    Manuals+ clarified question
    Question

    How do I diagnose and repair a loose connection on a Trim-A-Tree model 23142LO that causes lights to flicker or go dark?

    Answer

    Based on your description of the Trim-A-Tree model 23142LO (manufactured by Nicolas Holiday/GE), if you have already replaced the transformer and confirmed voltage is present, the issue likely resides in the control hardware or the physical connections between tree sections.

    Please try the following diagnostic steps:

    • Check the Foot Pedal/Inline Controller: The manual indicates that power and lighting modes are managed by a foot pedal switch. Since the lights go dark completely, there may be a loose solder joint or a failing component inside this controller. Try bypassing the foot pedal if the connectors allow, or gently tap the controller while the lights are on to see if it triggers the failure.
    • Inspect Section Connectors: Intermittent "all-dark" failures often occur at the poles where tree sections join. Ensure the internal pins in the center pole (if applicable) are clean, straight, and fully seated. Debris or slight misalignment here can cause the circuit to break as the tree settles.
    • Timer Mode Check: The manual mentions a Timer Mode that automatically turns lights off after 5 hours. While this wouldn't cause flickering, ensure the timer isn't being inadvertently activated by the remote or foot switch.
    • Remote Interference: Although less likely to cause a total blackout, the FCC documentation suggests that external radio interference can affect operation. Ensure no other high-powered electronic devices are near the receiver/controller.

    If the lights continue to flicker after checking the physical connections at the poles and the foot pedal, the internal control chip within the wiring harness may be failing, which is often not user-serviceable.

Ask a Question

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.