CT20 POS Terminal
“
Specifications:
- Dimensions: 125 mm x 78 mm
- Power on: Press button for 2-3 seconds to turn on
- Power off: Press button for several seconds, confirm power off
on screen
Product Usage Instructions:
Swiping Magnetic Strip Card:
1. Swipe the card with the magnetic strip facing the track
device inside.
2. Ensure stable and constant swiping motion for successful
transactions.
Using NFC:
1. Place the card close to the NFC area for one second.
2. Remove the card when you hear a Di voice and see the
confirmation on the screen.
Inserting SIM/PSAM/SD Card:
1. Open the battery cover and place the card in the card holder
with the chip facing inside.
2. Ensure the unit is turned off before installing or removing
the card to prevent damage.
Inserting Paper Roll:
1. Open the paper cabinet cover as shown.
2. Insert the paper roll into the holder, leaving a small
portion below the paper cutter.
3. Close the paper holder cover ensuring correct installation
direction.
Using IC Card Slot:
1. Locate the IC card slot at the bottom of the keypad.
2. Swipe the IC card with the chip side up and insert it fully
during transactions.
Tearing Print Paper:
Hold the print paper and tear it off from left to right with
fast and equal strength.
Frequently Asked Questions (FAQ):
Q: What should I do if my magnetic card transaction fails?
A: Check if the magnetic strip is damaged or if you are swiping
correctly. Ensure stable and constant swiping motion.
Q: How do I know if I inserted an IC card correctly?
A: Ensure the chip side is facing up and insert it fully into
the IC card slot. A failed transaction may occur if the chip
contact point is damaged or oxidative.
“`
)
(
125 mm
78 mm
Operating Temperature: -10 to 45°C Storage Temperature: -20°C to 70°C Relative Humidity: 5% to 95% (Non-Condensing) Please follow the instruction strictly when install and connect the terminal. Do not damage the power line and power adaptor. It can’t be used any more if the power line or power adaptor is damaged. Please check power supply socket whether complying with terminal set voltage before insert the AC socket. Recommend to choose the fuse socket, and grounding well. Please leave the terminal away from liquid, and forbidden splash into any liquid or electric conduction material, otherwise it will cause a short-circuit or damage to the terminal. Please do not insert any foreign material into any ports, it will damage the terminal seriously. Please contact the professional POS maintainer When the terminal have fault, users or other non-qualified POS maintainer should not repair the terminal. Please do not touch the cutter knife in case of hurt when install the paper roll. Please use the standard print paper in case of paper jam or printer damage. Please do not shake or knock the terminal. Please do not use or place flammability spray, painting, etc. in case of fire. Forbid to disassemble or remake the terminal. Forbidden to use the terminal in illegal way, offenders will stand legal responsibility.
Power on: Press ” ” for 2-3 seconds, screen backlight appear, and terminal power on. Power off: Press ” ” for several seconds, screen display “power off, please confirm or cancel”, press confirm, power off.
Please put the card magnetic strip towards to track device inside when swipe the card, it can support both directions; Make sure to swipe the card stably and constantly. Note: The transaction may be fail if magnetic card’s tripe is damaged or swipe solution is wrong.
Please put card close to the NFC area, and stay for one second, then remove card when you hear a “Di” voice, showing as follow picture.
1.open the battery cover. 2.Place the SIMPSAM/SD card in the card holder (the chip
of SIM/PSAM/SD card is oriented toward the inside of the machine).
Attention:
1.Install or remove SIM/PSAM/SD card, make sure the unit is turned off to avoid damage to the card.
2.SIM/PSAM/SD card can not contain, stickers or adhesive, which may affect the thickness of card and hinder, the smooth insertion or removal of cards.
1.Open the paper cabinet cover in the direction shown below.
2.Open the paper-roll and insert it into paper holder in the direction shown above, leaving a small portion of paper below the paper cutter.
3.Close the paper holder cover in the direction shown below.
Note: Make sure the paper-roll installed in the right direction or it will result in malfunction of the printer.
If the above solution can’t solve the problem or have other questions, please contact maintainer.
IC card slot locate in the bottom of the keypad, keep the chip side up when swiping card, and insert IC card to the end. The IC card should be inserted in the IC card slot during the transaction process.
Note: The transaction probably fail if IC card chip contact point is damaged or is oxidative.
Hold print paper, tear-off the print paper according to picture direction, keep direction from left to right, the strength should keep fast and equality during cutting paper.
INSPECTION CERTIFICATE
INSPECTOR: PLACE OF ORIGIN: Shenzhen,Guangdong DATE:
SHENZHEN XINGUODU TECHNOLOGY CO.,LTD
)
(
Documents / Resources
 |
NEXGO CT20 POS Terminal [pdf] Instruction Manual CT20-01, XDQCT20-01, XDQCT2001, CT20 POS Terminal, CT20, POS Terminal, Terminal |
