NEEWER MS60B Bluetooth Studio Light

Safety notes

• To ensure the safety of you and others, please ensure you read the following safety advice before using this product.
• Please pay attention to the precautions highlighted in the manual.
• The product should be checked before use and not used if damaged.
• Do not place flammable materials near the constant video light.
• Please use a blower brush or clean cloth to remove dust and moisture.
• Do not expose the product to direct sunlight for long periods. The product should not be stored in direct sunlight.
• Do not cover the ventilation holes at any time.
• Do not attempt to disassemble or repair the device.
• Do not use in the rain, a humid environment, or other adverse weather conditions.
• Keep the working environment clear of cables. Keep this product out of reach of children and pets.
• Please turn off and remove the power supply before maintenance, and installing or removing accessories.
• Do not use chemicals or liquids to clean the lamp. Do not immerse any part of the device in liquid.
• The constant video light will heat up during use.
• Do not touch with your hands.

About this Product

• With its compact design and high illuminance, the MS60B is a dimmable bi-color studio light featuring a dual power supply. Highly portable and can be handheld, it is the perfect choice for ‘on the go photography.
• Thanks to the CCT bi-color and FX special scene modes, the MS60B is well suited for video recording, studio photography, still-life photography, interview lighting and more.

Specifications

Product Model	MS60B
lnputVoltage	DC 20V 3.6A
Brightness Range	0-100
Color Temperature Range	2700K~6500K
Channels Available	00-99
Color Rendering lndex(CRI)	97+
Power	65W
llluminance	40000 Lux/lm, ll0000Lux/0.Sm
Frequency	1-10
Special Scenes	12 types
Frequency Range	2402MHz-2480MHz
Maximum radio-frequency power	1.76dBm

Product Illustration

Components

1. Reflector
2. Battery Release tab
3. Battery Adapter
4. Reflector Latch
5. Heat Dissipation Holes
6. Bracket Securing Knob
7. Angle Adjustment Knob
8. Battery Compartment Lock
9. For light stand attachment

Control Panel Illustration

1. Display
2. Rotate the dial to adjust the light’s brightness;
   • Press the dial: mode switch (short press); to show the light’s internal temperature (long press)
3. Short press to switch between 2.4G and Infinity connection types.
   • Long press to adjust channel (CH).
4. Power Jack
5. Rotate the dial: change settings;
   • Press the dial: move to the next item (short press), button lock (long press).
6. Short press: enter/exit standby mode;
   • Long press: power on/off.
   • Long press the “BT-RST” combination key to reset Infinity.

Display Illustration

1. CCT Mode
2. Button Lock
3. Channel
4. Brightness
5. Power Supply
6. Color Temperature
7. FX Mode (Special Effect)
8. Remaining Battery Level
9. Bluetooth
10. Scene
11. Frequency
12. Brightness

How to Assemble

Installing the studio light

1. Push the latch toward the back, turn the protective cover counterclockwise until the tabs are aligned with the gaps, and then remove the protective cover.
2. Align the tabs on the reflector with the holes, push the reflector in and rotate clockwise until the reflector snaps into place.
3. Insert the bracket screw into the light’s bottom screw hole, then rotate the bracket securing knob counterclockwise to firmly lock it in place.
4. Connect the mounting bracket to a light stand, then rotate the Stand Securing Knob to hold securely.
5. Rotate the Angle Adjustment lever to loosen, then adjust the studio light to the required angle and tighten the lever again.

Mount the battery adapter

1. Push the Battery Adapter Lock up and hold until the battery Adapter is put into place on the bracket.
2. Power cable connection.
   • Note: the light stand and battery are NOT included.

Installing the Bowens Mount Adapter Ring

• If you need to use a Bowens type mount, you can install this Bowens Mount Adapter Ring.
• Install the Bowens mount adapter ring in the right position first. The tabs will seem as if they are obstructing the Bowen’s mount itself.
• Lift the tabs on both sides for the ring to fit. Once the tabs are completely inserted into the positioning holes of the Bowens mount, tighten the twist knob at the bottom to secure the adapter ring fully.
• The Bowens Mount Adapter Ring and reflector should not be used at the same time.

How to Use

Powering the studio light

• Source 1: powered by compatible batteries
• Compatible battery types:
  • NP-F750. NP-F970
• Source 2: powered by AC adapter

Power on/off & Standby

1. Long press the “ON/OFF” button to turn the studio light on/off.
2. Short press the “ON/OFF” button to enter or exit the standby mode.

Setting the Light Brightness

• In any mode, rotate the knob to adjust the brightness level of the light between 0 and 100%.

Adjusting the Color Temperature

1. Short press theknob to switch to CCT mode.
2. Rotate theknob to adjust color temperature between 2700K and 6500K.

Scene/Frequency

1. Short press theknob to switch to FX mode.
2. Short press thebutton to change special effects. Rotate the knob to choose one of the light scenes from F01 to F12.
3. Short press thebutton again to select “FRQ”, then rotate theknob to set frequency between 01 and 10.

Light Scenes Illustration

Infinity Mode

• Short press thebutton until the display shows thesymbol to indicate that the light is in Infinity mode.
• Connect the NEEWER app via Bluetooth to control the light. For detailed instructions, please scan the QR code on the App Leaflet.
• When the symbol has stopped flashing on the display, the light has been successfully connected
• Please reset Infinity mode before connecting with the App. Long press the “BT-RST” combination buttons to reset Infinity.

2.4G Mode

1. Short press thebutton until the display shows ” CH ” value, which indicates the light has entered 2.4G mode.
2. Long press thebutton to select CH, then rotate the knob to set light channel from Channel 00 to Channel 99. Press the button again to confirm.
3. In 2.4G mode, you can set multiple LED lights to the same channel, such as CH88. Changing the light settings on one of the lights will result in the settings on other lights to change in sync.

Checking the Light’s internal temperature

1. Long press thebutton to check the internal temperature of the light. Short press the button to exit.
2. Rotate theknob to switch between Celsius and Fahrenheit.

Button Lock

In any mode, long press thebutton to lock or unlock the buttons on the light.

Notes

1. Do not drop the product or expose it to a strong physical impact.
2. When using, do not look directly at the light to prevent possible damage to your eyesight.
3. Do not place the product near inflammable and explosive materials.
4. Do not use the product in a damp or humid environment.
5. Do not touch the product with wet hands.
6. Please turn off the power when not in use.
7. If not to be used for a long period, the product should be kept in a ventilated, dry place away from heat sources and magnetic fields.

Documents / Resources

NEEWER MS60B Bluetooth Studio Light [pdf] Instruction Manual MS60B, MS60B Bluetooth Studio Light, Bluetooth Studio Light, Studio Light, Light

References

• User Manual