MuxLab HDMI/3G-SDI Dual Display Multiscreen Video Monitor User Manual

Dual 7-inch IPS LCD displays Supports HDMI (4K/30), 3G-SDI and CVBS with Audio
Fits 19-inch rackmount @ 3 RU Tri-color Tally light indicator per display Waveform: RGB, YUV, Y Histogram, Vectorscope Supports Center Marker, Safe Frames, Check Field, Focus Assist, Aspect Ratio, Image Flip, P2P & Image Freeze Customizable buttons tailored to customer needs Supports firmware update via mini USB

Package Contents

One (1) HDMI/3G-SDI Dual Display, 4K/30
One (1) 12VDC/3A Multinational Power Supply
One (1) User manual (available via download)

FAQs

Q: Can I update the firmware of the device?
A: Yes, the device supports firmware updates via mini USB.
Q: What is the warranty period for this product?
A: The product comes with a warranty of 2 years.

HDMI/3G-SDI Dual Display, 4K/30User Manual500841-V2

Safety Precautions

To ensure the best performance from the product, please read all instructions carefully before using the device. Save this manual for future reference.

Follow basic safety precautions to reduce the risk of fire, electrical shock, and injury.

Do not dismantle the housing or modify the module. It may result in electrical shock or burns.
Do not open or remove the housing of the device as you may be exposed to dangerous voltage or other hazards.
To prevent fire or shock hazard, do not expose the unit to rain, moisture and do not install this product near water. Keep the product away from liquids.

Spillage into the housing may result in fire, electrical shock, or equipment damage. If an object or liquid falls or spills on the housing, unplug the module immediately.
Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before cleaning.
Using supplies or parts not meeting the product specifications may cause damage, deterioration or malfunction.

Refer all servicing to qualified service personnel.
Install the device in a place with adequate ventilation to avoid damage caused by overheat.
Unplug the power when left unused for a long period of time.

Information on disposal of devices: do not burn or mix with general household waste, please treat them as normal electrical waste.

Copyright Notice
All contents in this manual are copyrighted, and cannot be cloned, copied, or translated without the express permission of MuxLab Inc. Product specifications and information in this document are for reference only, and the content may be updated from time to time without prior notice.

Introduction

The HDMI/3G-SDI Dual Display, 4K/30 (model: 500841-V2) supports two independent 7 inch IPS LCD displays mounted conveniently and securely on a 3 RU 19” rack. These devices save a significant amount of space in multi-display Pro AV and Broadcast applications.
The unit supports input and loop-out of HDMI signals up to 4K/30, SDI signals up to 3G-SDI, and CVBS signals with Audio. The unit supports a tri-color Tally light indicator per display, customizable buttons allowing customers to tailor them to their needs, and advanced functions such as Center Marker, Safe Frames, Check Field, Focus Assist, Aspect Ratio, Image Flip, P2P, Vectorscope, histogram and Image Freeze.

Features

Dual 7-inch IPS LCD displays
Supports HDMI (4K/30), 3G-SDI and CVBS with Audio
Fits 19-inch rackmount @ 3 RU

Tri-color Tally light indicator per display
Waveform: RGB, YUV, Y
Histogram, Vectorscope

Supports Center Marker, Safe Frames, Check Field, Focus
Assist, Aspect Ratio, Image Flip, P2P & Image Freeze
Customizable buttons tailored to customer needs

Supports firmware update via mini USB

Package Contents

One (1) HDMI/3G-SDI Dual Display, 4K/30
One (1) 12VDC/3A Multinational Power Supply

One (1) User manual (available via download)

Notes：Confirm that the product and accessories are all included. If not, please contact the supplier from which you purchased the unit.

Specifications



Screen Size	Two 7″ screens
Resolution	1920×1200 pixel
Dot Pitch	0.07875 (W) x 0.07875 (H) mm
Aspect Radio	16:10
Brightness	450cd/m2
Contrast	1100:1
Backlight	LED
Viewing Angle	80°/80°(L/R) 80°/80°(U/D)
Inputs	HDMI, 3G/HD/SD-SDI, Audio(L/R), Video
Outputs	HDMI, 3G/HD/SD-SDI, Video, 3.5mm Audio Jack
Control Inputs	Ethernet
	720p (60/59.94/50/30/29/25/24/23.98)
SDI Support Format	1080i (60/59.94/50) 1080p (60/59.94/50/30/29.97/25/24/24sF/23.98/23.98sF)
	480i/576i/480p/576p
	720p (60/59.94/50/30/29.97/25/24/23.98)
HDMI Support Format	1080i (60/59.94/50)
	1080p (60/59.94/50/30/29.97/25/24/23.98
	4K 3840x2160p (30/29.97/25/24/23.98Hz)
	4096x2160p (24Hz)
Power Consumption	≤21W
Input Voltage	9.0 to 24VDC
Power Source	100/240VAC to 12VDC @ 3A power supply
Working Temperature	0°C to 50°C
Storage Temperature	-20°C to 60°C
Install Way	Rack Mount
Dimensions	482.6L X 132H X 30.5D mm
Weight	1.89kg
Warranty	2 years
Order Information	500841-V2 HDMI/3G-SDI Dual Display, 4K/30 (UPC: 627699028414)

Product Description

Front Panel Description

Rear Panel Description

Power Input Way
There are two ways to power the monitor:

Through a power supply connected to a 2.1mm DC socket. Check that the power input polarity is as shown below.
Please use a qualified power supply with an output power of no less than 21W 9-24VDC.
Through a power supply connected to the 4-pin XLR interface. The polarity of the 4-pin XLR power input is shown below.

Tally Indicator Connection
Input signal. Each of two Tally lights support three colors, green, red and yellow, depending on the input applied.

Display Operation Instructions

Connect the provided power supply into the unit. The two displays will turn on, and the unit is ready to use. The user can operate and set each display as necessary via the corresponding buttons next to each screen.

Ethernet Connection
The 500841-V2 can be managed through the LAN port using the software control. Follow these instructions to control the display.

Connect your computer into the Ethernet port (or through a network switch/router). IP address will be displayed in the monitor.

Open the folder which should be previously downloaded in the computer and click on the Monitor Control.exe icon
Login and add monitor
Enter IP address

Select the display you wish to control
If the unit is connected, the IP will be displayed at the bottom
Three tabs will appear: Control, Function1 and Function2

Control Tab
It allows you to navigate through the menu, access to the interfaces among others functions.

Funtion1 Tab
It allows you to change the ratio mode, control aspect ratio, image freeze, etc. See screenshot for details.

Funtion2 Tab
In this tab, user has access to Image flip, histogram, vectorgram among others parameters. See below for more details:

Menu Function Instruction
Assist

Mark

Display

User


LUT	On, Off After the LUT Switch is turned on, you can use the Lut (SLOG2, SLOG3, LOGC, VLOG). Lut Import：Confirm After copying the 3D LUT file to the USB flash drive and inserting it into USB adapter cable (USB-female to mini-USB) press MENU button Confirm to import the 3D LUT file. Lut Table Show the 4 built-in Lut and the custom load Lut (up to 32）
Backlight：0~100
Brightness：0~100
Display Adjustment Contrast：0~100
Saturation：0~100
Tint：0~100
Color Adjustment	Color Temp.：5600K, 6500K, 9300K, User Under the User, the red, green and blue of the image can be adjusted (0~255)
Shortcut Key	User can configure the 2 custom shortcut buttons F1, F2 on the panel. Ex: Press MENU button to enter the menu, select User and press MENU to confirm. Then press the shortcut key and press MENU to confirm, select F1 and confirm to pop up the function items, then select one of them and press to confirm, the cursor will change to gray color after confirming. Same settings for F2.

System

Troubleshooting

If there is any problem when using the unit, please try following ways to inspect and solve. Please contact us if you still can not solve it or have other problems.

Only Monochrome or Single Color Image/Video

Check the Saturation, Brightness & Contrast adjustment.
Check the unit “Check Field” settings. Is “Check Field” in Monochrome image/video, or in another single color state? If so, change to “Color” mode.

No Image/Video after Power On

Check condition of the signal cable and connection. Also if the display is correctly synchronized with the input signal. Press the “Mode” button to test and confirm the correct setting.
Make sure to use a standard AV connector/ adapter to connect to the unit.

No Sound Output

Volume control may be too low. Press the Volume Up button to increase the volume.
Check the source Audio signal and confirm that Audio is present. If available, test on a separate device.

Application Example

salesteam@muxlab.com | www.muxlab.com

HDMI/3G-SDI Dual Display, 4K/30 500841-V2

Documents / Resources

MuxLab HDMI/3G-SDI Dual Display Multiscreen Video Monitor [pdf] User Manual
HDMI3G-SDI Dual Display Multiscreen Video Monitor, HDMI3G-SDI, Dual Display Multiscreen Video Monitor, Multiscreen Video Monitor, Video Monitor, Monitor

References

User Manual

MuxLab HDMI/3G-SDI Dual Display Multiscreen Video Monitor