MULTIBRACKETS 5605 Wall Bracket Installation Guide

MULTIBRACKETS 5605 Wall Bracket

Speċifikazzjoni

• Prodott: MULTIBRACKETS 5605 Universal Wall Bracket / Long Reach Arm Mount
• Tip: Full-motion articulating TV wall mount (dual arm long-reach swivel)
• Kulur: Finitura tal-metall iswed
• Materjal: Heavy-duty solid steel construction
• Kompatibilità tal-Iskrin: Fits most flat-panel TVs 65″ – 110″ diagonal
• Max screen diagonal: ~279 cm (110″)
• Kapaċità tal-piż: Up to 125 kg (~275 lbs) load support
• Appoġġ VESA: Compatible with most VESA patterns from 100×100 mm up to 800×600 mm
• Movement & Adjustment: Full-motion swivel, tilt, and rotate at multiple pivot points
• Medda tal-inklinazzjoni: approx. -5° to +10°
• Swivel/rotation: approximately 60° to +60°
• Extension from wall: up to 980 mm (~38.6″)
• Karatteristiċi:
  • Dual long-reach arms for flexible viewpożizzjonijiet
  • Smart cable management system to hide cables
  • Partially pre-assembled with a full hardware kit included
• Tip ta' Installazzjoni: Wall mount, articulating bracket
• Kulur: Iswed

IMPORTANTI!
Your Plasma. LCD. TV, Projector, Projector Screen, or other HiFi equipment represents a considerable value.
If screws are Included they may not be suitable for the material of your wall, ceiling, or floor. Replace the screws with suitable ones if needed.
In case you are unsure regarding any aspects or the mounting of this product,t please
Ikkonsulta professjonist.

Twissija!
Dejjem iċċekkja il fond of il toqob qabel bidu an installazzjoni.

Fits most 65″-110″ flat panel TV

• Weight capacity: 125kg/275 lbs
• VESA compliance: 100×100 200×200 300×300 400×200 400×400 600×400 800×600

TWISSIJA 
Korriment personali gravi u ħsara lill-proprjetà jistgħu jirriżultaw minn installazzjoni jew assemblaġġ mhux xieraq. Aqra bir-reqqa t-twissija li ġejja qabel tibda.

• Il-prodotti għandhom jiġu installati minn professjonisti.
• Jekk ma tifhimx l-istruzzjonijiet jew għandek xi tħassib jew mistoqsijiet, jekk jogħġbok ikkuntattja installatur lokali kwalifikat.
• Tinstallax jew tgħaqqadx jekk il-prodott jew il-ħardwer ikun bil-ħsara jew nieqes. Jekk teħtieġ partijiet ta 'sostituzzjoni, jekk jogħġbok ikkuntattja lid-distributur lokali tiegħek għall-għajnuna.
• This product fits most65″-11D”LCD and plasma screens; maximum weight of LCD /plasma screen: 125kg.
• This product has been designed for use on masonry (solid concrete, 2000 PSI density minimum).
• For safe installation. The wall you are mounting to must support a minimum of 3 times the weight of the total load (the mount, the TV, and all accessories).
• Tużax dan il-prodott għal kwalunkwe applikazzjoni oħra għajr id-disinn oriġinarjament.
• This product contains moving parts; please use it with caution.
• When installing a flat panel display, please do not damage the electrical wiring or the power source.
• Il-manifattur ma jkollu l-ebda responsabbiltà għall-immuntar mal-ħajt vertikali, jew ħsarat inċidentali jew konsegwenzjali li jirriżultaw minnu.
• Il-manifattur jiċħad kwalunkwe responsabbiltà għall-modifiki, installazzjoni mhux xierqa, jew installazzjoni fuq il-firxa ta 'piż speċifikata.
• The manufacturer will not be liable for any damages arising out of the use of, or inabilityto use, the product.

Lista tal-passat

INSTALLAZZJONI

INSTALLATION OPTION 1: Wood Stud Installation (Suitable for 16″ or 24″ apart studs)

1. Use a stud finder to locate the drywall studs and mark the desired installation locations with a pencil.
2. Waħħal il-Mudell tal-Pjanċa tal-Ħajt (BB) mal-ħajt fil-post tal-installazzjoni mixtieq.
3. Ensure the Wall Plate Template (BB) horizontal alignment is verified with a bubble level, and mark 6 lag bolt installation locations on the stencil and the wall. Attempt to locate the lag bolt locations in the middle of the studs.
4. Use a 7/32″ (5.5mm) drill bit to drill a pilot hole in the wall with a depth of at least 2.6″ (65mm).

Please note that failure to drill pilot holes may result in the lag bolt heads snapping during installation.

Secure the Wall Plate to the wall with 6 x Lag Bolts ( H) and 6 x Washers (H).

NOTA: Do not use Wall Anchor (I) for wood stud installation.

GĦAŻLA TA 'INSTALLAZZJONI 2: Installazzjoni tal-Ħitan tal-Konkrit/Briks

1. Waħħal il-Mudell tal-Pjanċa tal-Ħajt (BB) mal-ħajt fil-post tal-installazzjoni mixtieq.
2. Ensure the Wall Plate Template (BB) horizontal alignment is verified with a bubble level, and mark 6 lag bolt installation locations on the stencil and the wall.
3. Use a 3/8″ (10 mm) drill bit to drill a pilot hole in the wall with a depth of at least 2.6″ (65mm). Please note that failure to drill pilot holes may result in the lag bolt heads snapping during installation.

Daħħal 6 x Ankri tal-Ħajt (I) fit-toqob. Waħħal il-Pjanċa tal-Ħajt mal-ħajt b'6 x Lag Bolts (H) u 6 x Washers (H).

This full motion TV wall mount comes with a sliding mechanism that allows the arms and the TV to slide horizontally left or right for up to 15. 7 inches, while the wall plate is stationary on the wall. This feature allows the TV to be placed at an optimal position, regardless of the position of the wall studs. The mount will ship with the locking bars installed in place at their center position. If the sliding function will be used, take off the locking plates by removing the bolts that hold them in place.

Place the top locking bar at the desired position to fix the left slide limit of the arms, and place the bottom bar at the desired position to fix the right side limit of the arms. The raised metal piece at the end of the locking bars limits the slide of the arms. Ensure the locking bars are oriented correctly to ensure both the left and right side locking bars correctly limit the slide. Ensure both of the bolts are tightened at each locking bar’s position to prevent the arms from sliding off the wall plate.

TWISSIJA: FAILURE TO INSTALL THE LOCKING BARS ADEQUATELY MAY RESULT IN THE ARMS AND THE TV FROM SLIDING OFF THE WALL PLATE.

Attaching the TV to the Mount (For Displays With Smaller Bolt Hole Patterns)
For TVs with smaller bolt hole patterns of VESA 100×100, 100×200, 200×100, and 200x200mm, the TV can be mounted directly on the plate, without the extension bars.

It-twaħħil tat-TV mal-Mountaġġ (Għal Displays B'Disinji Akbar ta' Toqba Bolt) Għal televiżjonijiet b'disinji akbar ta' toqba tal-bolt ta' VESA 300 × 300,400 × 200,400 × 400,600 × 400, 800 × 600 mm, uża l-parentesi tat-TV u l-vireg tal-estensjoni biex tinstalla l- TV għall-muntatura.

Attach the 2 x TV Brackets to the back of the TV by using screws A+E, B+E, C+E, or Dor G.

NOTA: The hardware packet provided fits most TVs in the market. If your TV requires different hardware, please contact us at mount-it.com to procure additional hardware kits.

Ensure the screws are adequately engaged with the screw holes on the TV.
Do not overtighten the screws. Ensure the TV brackets sit flat with the back of the T.V.

Hangina g TV On The Wall Mount Arms

Lift the TV (two persons recommended) and hang the TV brackets onto the wall mount extension bars.

Niżguraw It-TV Fuq Il-Muntanja

Secure the TV brackets on the mount by attaching the 4 x AA Safety Brackets with 4 x F Screws as shown ointhe image.

NOTA: Jekk il-parentesi tat-TV ma jiġux assigurati mal-muntatura b'Brackets tas-Sigurtà AA, jista' jirriżulta f'irfigħ aċċidentali tat-TV mill-vireg ta' estensjoni, li possibbilment jirriżulta fi ħsara fil-ġisem jew fil-proprjetà.

Aġġustament tal-livellar -5° – +5°
The mount allows up to 5 degrees of leveling adjustment post installation. To adjust the level of the TV, place a bubble level on top of the TV, loosen the 2 x G bolts located behind the VESA plate, level the TV, and tighten the 2 x G bolts to lock the TV in position.

Aġġustament tal-inklinazzjoni -5° – +10°

The mount can tilt down up to 10 degrees and up 5 degrees. To adjust the tilt angle of the TV, pull out the tilt adjustment levers on both sides of the mount and turn counterclockwise to loosen the screws. Adjust the tilt to the desired angle and turn the tilt adjustment lever clockwise to tighten the screws.

NOTA: IF THE TV TILTS DOWN AFTER A PERIOD OF USE, CHECK THE TILT ADJUSTMENT LEVER TIGHTNESS AND TIGHTEN IF NECESSARY.

Uża l-klipps integrati tal-ġestjoni tal-kejbils fuq id-dirgħajn biex tgħaddi l-kejbils fuq wara jew fuq il-ġenb tat-TV.

Dimensjoni

KARTA TAL-GARANZIJA

MALTABILJETTI “™ Limited Garanzija

Multibrackets mandati tagħha prodotti biex be ħielsa of difetti in materjal u abbilità għal il tal-prodott Garanzija Perjodu.

Il- Garanzija perjodu jibda on il oriġinali xiri data of il prodott

Kollha Multibrackets prodotti huma koperti by a limitati prodott garanzija

• ĦAMES (5) snin għal metall vidjo tissorvelja mounts, kollha xtillieriu non-electrical xtilliera aċċessorji
• TNEJN (2) snin għal gaslifts u sit-stand stazzjonijiet tax-xogħol
• WIEĦED (1) sena għal kollha bil-mutur u/jew awtomatizzat prodotti, plastik kelliem mounts, kollha kelliem stands, kollha għamara, kollhainjam (MDF) aċċessorji

Għal garanzija pretensjonijiet magħmula matul il Garanzija Perjodu, MULTIBRAZZETTI se ibdel kwalunkwe difettuż prodott parti ħielsa of charge. Should a parti on tiegħek Multibrackets prodott fail, jekk jogħġbok toħloq anRMA każ on www.multibrackets.com/support biex tagħmel a garanzijatalba. We se await tiegħek dokumentazzjoni u imbagħad discuss ilproblema ma int, u darba we confirm il prodott is taħt gwerraranty, we se vapur sostituzzjoni partijiet biex int. Dan Limited Garanzijajagħmel le kopertura il spejjeż of tneħħija u tissostitwixxi difettuż partijietminn tiegħek Multibrackets prodott. Allura, if tiegħek problema teħtieġ atiswija technician, int għandu tħallas kwalunkwe xogħol ħlasijiet.

For warranty claims made during the Warranty Period, MULTI BRACKETS will replace any defective product part free of charge. Should a part of your Multibrackets product fail, please create an RMA case on www.multibrackets.com/support to make a warranty claim. We will await your documentation and then discuss the problem with you, and once we confirm the product is under warranty, we will ship replacement parts to you. This

Limited Warranty does not cover the costs of removing and replacing defective parts from your Multibrackets product. So, if your problem requires arepair technician, you must pay any labor charg.es This Limited Warranty extends only to the original purchaser of the product and is automatically void if your Multibrackets product is modified in any way, improperly installed, taxed beyond its stated weight capacity, or otherwise misused or abused.

All Multibrackets products are intended for indoor use only, and any outdoor use voids this Limited Warranty. The Limited Warranty for wall and ceiling mounts is void if the mount is moved from its initial installation. To the maximum extent permitted by applicable law, Multibrackets disclaims any other warranties, express or implied, including warranties of fitness for a particular purpose and warranties of merchantability. Multibrackets will not be liable for any damages whatsoever arising out of the use or inability to use itsproducts, even if Multibrackets has been advised of the possibility of such damages. To the maximum extent permitted by applicablelaw, Multibrackets disclaims any responsibility for incidental or consequential damages,

Multibrackets M Stockholm, Sweden 2016. www.multibrackets.com

The content of this manual is subject to Change wltheut further notice. The latest vers, on of this manual can be found online under the product name on the websit: www.multibrackets.com