Android Car Player Instruction Manual

Android Car Player Instruction

SPEĊIFIKAZZJONI

• power Supply Volllgo
• Konsum Kurrenti Max
• Max Output Power

1. UNIVERSAL MACHINE WIRING DIAGRAM
   
2. SPECIAL VEHICLE WIRING DIAGRAM

PREKAWZJONIJIET TAL-WIREING

• 10P: Connect the reversing video input. Note: The two short wires above this line are the Bluetooth antenna and the WIFI antenna. Even if the reversing camera is not connected, this cable needs to be connected to the machine, otherwise Bluetooth and WIFI will not be connected, and carplay and Android auto will not be connected.
• 6P: Connect USB-2.
• 4P. Connect USB-1.
• 8P: Connect the CANBUS box. Note: When the product you purchased has a CANBUS box, you must connect the CANBUS box to the
• 8Pin socket on the body, otherwise some of the original car functions will not be available.
• 12P.360-degree panoramic reversing image (only supported by some models).
• 20P.RCA plug. The AMP CONT line needs to pay attention to: If your car supports speakers such as JBL or BOSE, you may need to connect this cable to the on-off control of your car’s power amplifier, and try connecting it when there is no sound.

METODU TA' INSTALLAZZJONI TAL-KAMERA TAR-RIVERS

STRUZZJONIJIET GĦALL-KORD TAL-ENERĠIJA UNIVERSALI

Tips The wiring harness colors of some models may be different. Please refer to the wire labels and the positions on the plugs and sockets.

UNIVERSAL MACHINE POWER PIN DEFINITION

TAGĦLIM KONTROLLI TA ' L-IMMANU
Agħfas u żomm buttuna fuq l-isteering tal-karozza oriġinali u sib l-ikona tal-buttuna li tikkorrispondi għall-funzjoni tal-buttuna fuq l-isteering. Ikklikkja l-ikona biex tbiddel il-kulur, it-tagħlim huwa ta 'suċċess.

iPHONE Mirrorlink (Jappoġġjawh biss xi mudelli)
Meta l-apparat jiġi pplaggjat fl-iPhone, il-kontenut tal-iskrin tat-telefon jiġi pproġettat fuq l-iskrin tal-karozza.

Android Mirrorlink (Jappoġġjawh biss xi mudelli)
When using an Android device, after connecting the USB data cable. you will be prompted to install the APP software. After installation, Plug the data cable again, it will enter the screen mirroring mode. And it can be operatedon both the player screen and the phone screen. Only the image transfer is successful at this time. The sound can only be  transmitted after the Bluetooth connection is successful.

Apple Car Play (Only some models support)

1. Wired connection: Just connect the USB data cable, and then it will auto matically enter the CarPlay interface.
2. Wireless connection: first tum on the bluetooth and wifi functions of the mobile phone. and then connect the bluetooth. Then it will automatically enter the CarPlay interface.
   (Note. The signal is transmitted through wifi at this ime, so even if the Bluetooth function is tumed off, it will be transmitted normally. When the wifi function is turned off. CarPlay will be disconnected.)

Android Auto (Jappoġġjawh biss xi mudelli)
Din il-karatteristika mhix appoġġata fil-pajjiżi kollha, u “is-servizzi ta’ Google Play jeħtieġ li jkunu disponibbli lokalment.

1. Ħtieġa li tniżżel u tinstalla "Android Auto" software in “Google Play”
2. Għandu jintuża mowbajl b'Android 6.0 jew ogħla. Trid tuża konnessjoni valida tal-kejbil tad-data.
3. Konnessjoni bil-fili: Ikkonnettja biss il-kejbil tad-data USB, u mbagħad tidħol awtomatikament fl-interface Android Auto.
4. Wireless connection: First turn on the Bluetooth and wifi functions of the mobile phone. and then connect the Bluetooth. Then it will automatically enter the Android Auto interface. (Note: The signal is transmitted through wifi at this time, so even if the Bluetooth function is turned off, it will be transmitted normally. When the wifi function is turned off, Android Auto will be disconnected.)

PROBLEMI KOMUNI U SOLUZZJONI TA’ PROBLEMI SEMPLIĊI

Ma tistax tibbotja normalment

1. “Yellow” “Red” “Black’ this 3 lines only connected 2 line of them, so it will not start, it should be that the yellow line is connected to the positive pole, red line to the key control line, black to the negative pole, less connection or wrong connection does not boot.
2. Il-linja oriġinali tal-karozza u l-wajers tal-unità ma jistgħux jiġu konnessi mal-kulur, il-kulur tal-linja oriġinali tal-karozza mhuwiex standard, jekk tikkonnettja bħal dik tista 'mhux biss tinxtegħel iżda wkoll tista' tinħaraq.
3. Il-plagg oriġinali tal-karozza ma jistax jiġi pplaggjat direttament fl-unità l-ġdida, anke jekk sempliċement jiġi pplaggjat, ma jistax jintuża. inkella ma jinxtegħelx jew jinħaraq.
4. It-3 wajers huma konnessi dritt, iżda ma bootx. Iċċekkja jekk il-fjus fuq il-linja safra huwiex miksur. Jekk ma jkun hemm l-ebda problema bil-fjus, dawwar il-wajers isfar u ħomor flimkien. Ixgħel iċ-ċavetta u agħfas il-buttuna tal-enerġija tal-unità biex tara jekk tistax tinxtegħel.
5. Every time you change the fuse, it burns. Please don’t change it again The reason is that when you first connect the positive and negative poles, the protection circuit of the unit is short-circuited. The unit can be repairedunder the guidance of our master. No basis can only be returned to the after-sales or new unit. If these are no problem, or also don’t boot, please make the final step to confirm, find a 12V battery or 12V power supply yellow and “red twist together with the positive, black to the negative pole. press the button check if it can boot or no, if you can boot, it showed that the original car line is not right connect, or there is a problem with the car line.  If it can’t be boot, the unit is broken. Does not boot unit, check the line carefully, do not blindly suspect the unit problem.

Tfigħ awtomatiku

1. L-iżball tal-kejbil jgħaqqad: Jekk il-kejbil blu (provvista ta 'enerġija ta' l-antenna awtomatika) ikun imqabbad mal-kejbil ta 'l-enerġija ta' l-unità, se jseħħ għeluq awtomatiku. Jekk jogħġbok segwi l-metodu korrett tal-wajers biex issolvi l-problema.
2. Il-voltage hija instabbli: jekk jogħġbok sib 12V-5A liema waħda hija l-provvista tal-enerġija u ttestjata mill-ġdid biex tara jekk tingħalaq awtomatikament. Jekk ma tintefax awtomatikament wara t-test, jekk jogħġbok ibdel il-provvista tal-enerġija. Jekk se tintefa awtomatikament, hija problema bl-unità.

Hemm storbju

1. Il-qawwa oriġinali tal-kelliem hija żgħira wisq. Meta l-volum ta 'l-unità huwa mdawwar. se jkun hemm storbju.
   Soluzzjoni: Meta tissostitwixxi l-kelliem jew tisma 'l-kanzunetta, il-volum m'għandux ikun kbir wisq.

Il-kejbil tal-kelliem huwa ertjat.
Soluzzjoni: Ħu l-kejbil tal-ispiker tal-ħadid. Imqabbad direttament mal-kejbil tal-kelliem tal-unità.

Kontroll mill-bogħod ma jistax jintuża

1. Test method Turn on the camera of the mobile phone and align the light of the remote control then press the button of the remote control to see if the phone will light up. If it is not lit there will be no power. Replace the battery: If it is it there is electricity, which proves that there is no problem with the remote control.

Is-settings ma jistgħux jiġu ssejvjati (l-ebda memorja)

1. Il-linja safra u l-linja ħamra huma konnessi flimkien (isfar separati għal kontroll pożittiv, aħmar għal kontroll ewlieni).
2. Isfar u aħmar huma maqluba (biss ibdel il-pożizzjoni).

Bluetooth mhux qed jaħdem
Ixgħel il-magna, fittex l-isem tal-Bluetooth tal-magna billi tuża l-Bluetooth tat-telefon ċellulari, u mbagħad ikklikkja Connect, wara li tikkonnettja, tista 'twieġeb sejħiet jew tilgħab kanzunetti permezz tal-Bluetooth.

Il-prodott jarmi duħħan
Ibdel il-fjus FUSE, jekk il-problema ma tistax tiġi solvuta, iċ-ċirkwit intern ikun inħaraq. Servizz ta 'wara l-bejgħ huwa meħtieġ.

Il-ħoss ma jistax jiġi aġġustat

1. Jekk jogħġbok reset l-unità jew aqla' l-korda tad-dawl u plaggha.
2. The Volume knob is broken, and it can be replaced.

Il-kamera tar-rivers ma turiex

1. Wiring ħażin jew wajers nieqes.

Metodu ta 'konnessjoni tal-kamera:

1. Sib l-aċċessorji: 1 kamera + 1 korda tal-enerġija + 1 kejbil tal-vidjo.
2. Find the port of the wiring. First find the reverse control line on the power line of the unit. The control line is a pink line. Connect this line to the positive pole of 12V and the screen will turn blue. And then find the back of the unit the CAM video input interface, find the positive and negative of the backup light.
3. Hemm żewġ sokits fuq il-kamera, is-sokit aħmar huwa konness mal-kejbil tal-enerġija, l-isfar jiddaħħal fil-kejbil tal-vidjo, il-wajer aħmar tal-kejbil tal-enerġija u l-wajer tal-kejbil tal-vidjo huma invitati flimkien fuq l-arblu pożittiv tal- reverse lamp, and the black wire of the power cable is not used. connected, the other end of the video cable is connected to the CAM video input interface on the back of the unit. The red line coming out of the video line is connected to the reversing control line of the power line.
4. Il-kamera hija miksura. Jekk il-lamp li hija fili sew mal-kamera ma tkunx mixgħula. se jitkisser u jinbidel b'waħda ġdida.

Apparat USB ma jistax jintlagħab
Format il-flash disk USB, u l- file is-sistema hija magħżula bħala: FAT32, niżżel mill-ġdid fuq jew żewġ kanzunetti u erġa pprova. Jekk xorta ma taħdimx, jekk jogħġbok ibdel il-USB flash drive.

FM ma jirċievix l-istazzjon tar-radju

1. The antenna plug is not fully inserted, the antenna is disconnect or the line is disconnected.
2. Search station, press AS will automatically search or press the before or after button. Can’t solve the above 2 points. Please unplug the antenna plug and find a screwdriver or a metal strip to insert into the antenna.

M'hemm l-ebda ħoss dritt wara l-installazzjoni
Dear customers, the unit has been tested before shipment. If there is no sound, it is usually a wiring error or the original car speaker wire is short- circuited with iron. According to the steps to check it:

1. Iċċekkja jekk il-kejbil tal-kelliem huwiex short-circuited u konness. Jekk jogħġbok erġa' qabbad jekk għandek xi short circuit.
2. Check how many speaker cables according to the original speaker cable if there are only 2 speaker cables, to prove that the original car line does not match our unit, you need to re-route the original car line. One speaker must lead to 2 speaker wires. 2 speakers must be have 4 speaker cables to available.

M'hemm l-ebda ħoss wara xi żmien
Disconnect all the speaker cable from the unit (do not remove them), and then find an external speaker to receive the gray and purple of the tail line of the unit.Check any group, and then try to see if there is any sound If there is a sound, it is proven that the car’s speaker line is short-circuited with iron or the speaker is damaged. If there is no sound, the unit is broken.

Tips: If the device is updated, the functions are subject to change without prior notice