Alat Kawalan Jauh Keilton Basic RM51 untuk Penderia Lekapan

Penerangan

The RM51 Remote is used to program the configurations of the Keilton Basic sensors using infrared (IR) communications with the devices. It offers 6 default modes of configurations plus manual settings. Customer configurations can be created, saved, and then sent to each device, ensuring a rapid deployment.

Ciri-ciri

• Penggunaan kuasa yang rendah.
• Infrared communication.
• Setting most of the Keilton Sensors G2.
• Custom Configurations can be saved to A, B, C, D, or For.
• 40′ maximum IR range.
• RML (included with new orders, available as an accessory for order), installed, will increase the IR range. (See table below)

Spesifikasi

Maklumat Pesanan

Model	Penerangan
RM51.A0	Basic Sensor Controller RM51
RM51.A1	Basic Sensor Controller RM51 With RML

Maklumat Pesanan – Aksesori

Model	Penerangan
RML	Extended IR range for commissioning

Dimensi

Label Produk

Arahan Jauh

Mod Memori (Pentauliahan)
To begin commissioning, follow these steps:

1. Pilih memori profile: A, B, C, D atau E.
2. The remote’s indicator lights will flash, indicating the currently saved settings.
3. Settings can be configured by pressing the appropriate buttons in the highlighted gray area of the remote (TRIM-LEVEL, SENSITIVITY, HOLD TIME, STANDBY DIM, STANDBY TIME, and PHOTOCELL). Review the selected settings and make changes as needed.
4. Point the remote at the desired luminaire and press “SEND.”
5. The luminaire will flash twice to confirm that he settings are saved. Changing a parameter in a memory profile will automatically override previous settings.
6. If configuring multiple luminaires, repeat steps 4 and 5 after selecting the configured memory mode.

E Mode allows for visual adjustment to choose the desired dimming level.

Penuaian Siang Hari (Mod F)
Continuous Adjustment Mode adjusts dimming levels based on daylight.

1. Point the remote at the desired luminaire and press “ON,” then press DIM+ or DIM- to adjust the dimming level.
2. Press “F.” The indicator lights on the remote will show the current saved settings. Note: Only TRIM-LEVEL, SENSITIVITY, and HOLD TIME can be selected for Daylight Harvesting settings
3. Review the selected settings and make changes as necessary. Press “SEND.”
4. If the configuration is successful, the luminaire will flash twice to confirm that the setting is saved. If configuring multiple luminaires, select the configured Daylight Harvesting settings, then follow steps 1, 2, and 3.

Fungsi Jauh Tambahan

ON	Berpusing ON lampu penerang.
DIMATIKAN	Berpusing DIMATIKAN lampu penerang.
UJIAN	The fixture enters the test mode and exits automatically after 5 minutes. The test mode parameters are configured as follows: Trim-level: 100%, Sensitiviti: TINGGI, Masa tahan: 2s, Standby dim: 50%, Masa siap sedia: 2s.
TETAP SEMULA	Trim= 100%, Sensitivity = tinggi, T1 = 5 min, Standby Dim = 30%, T2 = 60 min, Photocell = DIMATIKAN.
DIM+/-	Press Dim+ or Dim- to adjust brightness in 0.5V increments. Hold the button for continuous dimming
TAHAP TRIM	Set the Maximum brightness.
SENSITIVITI	Set the motion sensitivity of the sensor RENDAH:50% / TINGGI:100%, MATI: disable the motion detection function.
HOLDTIME	Tempoh yang berlalu tanpa pengesanan penghunian sebelum beralih kepada malap siap sedia.
DIM STANDBY	Select any standby dim level.
STANDBY MASA	Standby time, when the time is set to “∞”, the daylight detection function is activated.
PHOTOCELL	visible light threshold, the fixture is allowed to be turned on when it falls below the threshold RENDAH:5fc / TINGGI:20fc, CAL: Collect the current visible light illuminance as the threshold, MATI: disable PHOTOCELL function.
MODE	Default configuration parameters for modes A kepada F.
HANTAR	Hantar tetapan kepada penderia.
LALAI MOD A	Trim= 100%, Sensitivity = rendah, T1 = 30 min, Standby Dim = 50%, T2 = ∞, Photocell = CAL.
MOD LALAI B	Trim= 100%, Sensitivity = rendah, T1 = 30 min, Standby Dim = 50%, T2 = 15 min, Photocell = CAL.
MOD lalai C	Trim= 100%, Sensitivity = rendah, T1 = 30 min, Standby Dim = 50%, T2 = 15 min, Photocell = DIMATIKAN.
MOD lalai D	Trim= 50%, Sensitivity = rendah, T1 = 30 s, Standby Dim = 50%, T2 = 30 min, Photocell = CAL.
MOD LALAI E	Manual Dimmer Mode, Trim 100%.
MOD LALAI F	Daylight Harvesting, Trim= 50%, Sensitivity = rendah, T1 = 15 min.

Hubungi Kami

• 7001 Columbia Gateway Drive, Suite 210, Columbia, MD 21046, USA
• T: +1 443-320-2233 (M-F 9 am-5 pm ET)
• E: support@autani.com

Soalan Lazim

How do I change the memory profile tetapan?

Select the desired memory profile on the remote and adjust settings as needed before pressing SEND to save

Can I configure Daylight Harvesting settings for multiple luminaires simultaneously?

No, you need to configure Daylight Harvesting settings for each luminaire individually using the F Mode on the remote.

What is the expected operation if the user sets Standby Time to something other than INFINITE?

moiton -> the intensity of ambient light is lower than the threshold set by the PC->turn on the light and dim to trim-level->t1 timeout->dim to standby dim ->t2 timeout->turn off the light.

If it does not turn OFF the fixture, why would Mode B and D use CAL as the default?

The ambient light intensity stored by CAL will serve as the threshold for turning on the lights, but it has no connection with the function of turning off the lights.

Dokumen / Sumber

Alat Kawalan Jauh Keilton Basic RM51 untuk Penderia Lekapan [pdf] Manual Pemilik RM51.A0, RM51.A1, RM51 Alat Kawalan Jauh untuk Penderia Lekapan, RM51, Alat Kawalan Jauh untuk Penderia Lekapan, untuk Penderia Lekapan, Penderia Lekapan

Rujukan

• Manual Pengguna