XTOOL OBD2 Main Test Cable (VGA to OBD2-16)

1. Produk Lebihview

This manual provides instructions for the XTOOL OBD2 Main Test Cable, designed for connecting XTOOL diagnostic scanners to vehicles. This cable facilitates communication between your scanner and the vehicle's On-Board Diagnostics (OBD2) system, enabling diagnostic functions.

The cable features a VGA (DB15) connector for the scanner side and a standard OBD2-16 pin connector for the vehicle side. It is constructed from durable, braided materials to ensure longevity and reliable performance.

2. Ciri-ciri Utama

• Keserasian Universal: Designed for use with various XTOOL scanners including IP508, IP508S, IP608, IP616, IP819, D7, and D7S. It is also compatible with other scanners utilizing the same VGA (DB15) interface.
• Pembinaan Tahan Lama: Made with premium nylon braided material, offering resistance to wear and tear for extended service life.
• Sambungan Selamat: Features a 16V rated male-to-male connection, ensuring stable and safe diagnostic operations.
• Panjang Optimum: Approximately 60 inches (152 cm) in length, providing flexibility during use.
• Reka Bentuk Bersepadu: This is a single-piece cable, eliminating the need for additional connectors.

3. Persediaan dan Pemasangan

1. Cari Port OBD2: Identify the OBD2 diagnostic port in your vehicle. This port is typically located under the dashboard on the driver's side, but its exact position may vary by vehicle model. Refer to your vehicle's owner's manual if needed.
2. Sambung ke Kenderaan: Plug the OBD2-16 pin connector end of the XTOOL Main Test Cable into the vehicle's OBD2 port. Ensure a firm and secure connection.
3. Sambungkan ke Pengimbas: Plug the VGA (DB15) connector end of the cable into the corresponding port on your XTOOL diagnostic scanner. Tighten any screws on the VGA connector if present to secure the connection.

Once both ends are securely connected, the cable is ready for use with your diagnostic scanner.

Image: Connection diagram for the XTOOL OBD2 Main Test Cable, illustrating the VGA connector for the scanner and the OBD2-16 pin connector for the vehicle.

Image: The XTOOL OBD2 Replacement Cable shown connected to a diagnostic device, highlighting its direct use as an integral part without needing another connector. Compatible XTOOL scanner models (IP508, IP508S, IP608, IP616, IP819, D7) are displayed.

4. Arahan Operasi

The XTOOL OBD2 Main Test Cable acts as a conduit for data transfer between your vehicle and the diagnostic scanner. Its operation is integrated with your specific XTOOL scanner model.

1. Power On Scanner: After connecting the cable to both the vehicle and the scanner, power on your XTOOL diagnostic scanner. The scanner typically draws power directly from the vehicle's OBD2 port.
2. Initiate Diagnostics: Follow the instructions on your XTOOL scanner's interface to select the desired diagnostic functions (e.g., read fault codes, view live data, perform special functions).
3. Pemindahan Data: The cable will facilitate the secure and stable transfer of diagnostic data between the vehicle's ECU and your scanner.

For detailed operational procedures specific to your diagnostic tasks, refer to the user manual of your XTOOL scanner.

5. Penyelenggaraan

• Storan: Store the cable in a clean, dry place away from direct sunlight and extreme temperatures. Avoid kinking or tightly coiling the cable to prevent internal wire damage.
• Pembersihan: Wipe the cable and connectors with a soft, dry cloth. Do not use harsh chemicals or abrasive cleaners, as these can damage the cable's insulation or connectors.
• Pemeriksaan: Periodically inspect the cable for any signs of wear, cuts, or damage to the connectors. If any damage is observed, discontinue use and replace the cable to ensure safe and reliable operation.
• Pengendalian: Always grasp the connector ends when plugging or unplugging the cable. Avoid pulling directly on the cable itself, as this can strain the connections and lead to damage.

6. Penyelesaian masalah

If you encounter issues while using the XTOOL OBD2 Main Test Cable, consider the following:

• Tiada Komunikasi:
  • Ensure both the OBD2 and VGA connectors are securely plugged into the vehicle and scanner, respectively.
  • Verify that the vehicle's ignition is on (or engine running, as required by your scanner/diagnostic task).
  • Check your XTOOL scanner's settings to ensure it is configured correctly for the vehicle type.
  • Inspect the cable for visible damage. A damaged cable may prevent communication.
• Sambungan Terputus-putus:
  • Ensure the VGA connector screws (if present) are tightened to prevent accidental disconnection.
  • Avoid excessive movement or strain on the cable during diagnostic procedures.
• Pengimbas Tidak Dihidupkan:
  • Confirm the vehicle's OBD2 port is supplying power. Some vehicles may require the ignition to be in the 'ON' position.
  • Check the vehicle's fuse for the OBD2 port if the scanner does not receive power.

If troubleshooting steps do not resolve the issue, contact XTOOL customer support for further assistance.

7. Spesifikasi

Image: The XTOOL OBD2 Main Test Cable, approximately 60 inches long, held by hands to illustrate its flexible and durable design.

8. Waranti dan Sokongan

For information regarding product warranty, returns, or technical support, please refer to the official XTOOL website or contact your authorized XTOOL dealer. Keep your purchase receipt as proof of purchase for any warranty claims.

XTOOL is committed to providing reliable products and customer service. If you experience any issues not covered in this manual, please reach out to their support team for expert assistance.