1. Produk Lebihview
The IBO S-150 is an electronic control unit designed for managing the circulation pump in a central heating system. Its primary function is to activate the pump when the water temperature exceeds a preset value and deactivate it when the temperature falls below that value. This intelligent control helps to optimize energy consumption and extend the operational lifespan of the pump.
Ciri-ciri Utama:
- Integrated Thermostat Function: Allows setting specific temperature thresholds for pump activation and deactivation.
- Fungsi anti-beku: Automatically activates the pump if the ambient temperature drops below 5 °C (41 °F) to prevent freezing within the system.
- Penjimatan Tenaga: Prevents unnecessary pump operation, leading to reduced energy consumption.
- Extended Pump Lifespan: Reduces wear and tear on the pump by operating it only when required.
- Penunjuk LED: Two LED displays show current temperature and set stop temperature.
- Antara Muka Mesra Pengguna: Simple button controls for setting parameters.
2. Maklumat Keselamatan
Sila baca semua arahan keselamatan dengan teliti sebelum pemasangan dan operasi. Kegagalan mematuhi arahan ini boleh mengakibatkan renjatan elektrik, kebakaran atau kecederaan serius.
- Keselamatan Elektrik: Installation and maintenance should only be performed by qualified personnel in accordance with local electrical codes and regulations.
- Pemutusan Kuasa: Always disconnect the power supply to the central heating system and the controller before performing any installation, wiring, or maintenance.
- Air dan Kelembapan: Do not expose the controller to water, excessive moisture, or extreme temperatures. Ensure the installation location is dry and protected.
- Pembumian yang betul: Pastikan peranti dibumikan dengan betul untuk mengelakkan bahaya elektrik.
- Integriti Kabel: Regularly inspect all cables for damage. Do not use the device if any cables are frayed or damaged.
- Penggunaan yang Dimaksudkan: Use the controller only for its intended purpose as a central heating pump controller.
3. Spesifikasi Teknikal
| Parameter | Nilai |
|---|---|
| Temperature Setting Range (Set Temperature) | 0 °C hingga 99 °C (32 °F hingga 210 °F) |
| Temperature Setting Range (Stop Temperature) | 0 °C hingga 99 °C (32 °F hingga 210 °F) |
| Suhu Ambien | -10 °C hingga 40 °C (14 °F hingga 104 °F) |
| Jenis Sensor Suhu | Ohmic |
| Bekalan Kuasa Voltage | 230 V, 50 Hz, ±10% |
| Power Consumption (Controller Only) | <5 W |
| Panjang Kabel Sensor | Kira-kira 1 m (3.3 kaki) |
| Panjang Kabel Kuasa | Kira-kira 1 m (3.3 kaki) |
| Pump Power Cable Length | Kira-kira 1 m (3.3 kaki) |
| Keluaran | 230V / 50Hz |
| Maximum Load (Pump) | 6 A (Resistive Load) |
| Ketepatan Pengukuran | ~0.1 °C |
| Dimensi Produk (L x W x H) | 14 x 14 x 5 cm (5.5 x 5.5 x 2 inci) |
| Berat badan | 370 gram (0.82 lbs) |
4. Pemasangan dan Persediaan
Before proceeding with installation, ensure the main power supply to your central heating system is turned off at the circuit breaker.
4.1. Memasang Pengawal
Select a suitable, dry location for mounting the controller, away from direct heat sources or excessive moisture. The controller can be mounted on a wall using appropriate fasteners (not included). Ensure sufficient space for cable connections.
4.2. Menyambungkan Kabel
The IBO S-150 controller comes with three main connections:
- Kabel kuasa: This cable supplies power to the controller. Plug it into a standard 230V, 50Hz electrical outlet.
- Pump Power Cable: This cable connects the controller to your central heating circulation pump. Ensure the pump is compatible with the controller's specifications (Max load: 6A).
- Temperature Sensor Cable: The ohmic temperature sensor should be placed in a location where it can accurately measure the water temperature of the central heating system. Typically, this is on the return pipe or a designated sensor pocket. Ensure good thermal contact for accurate readings.
Gambar 1: Lebihview of the IBO S-150 controller with its connected power, pump, and sensor cables.
Rajah 2: Bawah view of the controller, illustrating the connection points for the power and pump cables.
After all connections are securely made, restore power to the central heating system.
5. Operasi
The IBO S-150 controller features a simple interface with two LED displays and three control buttons.
Figure 3: Front panel of the IBO S-150 controller, showing the LED displays and control buttons.
5.1. Hidupkan Kuasa Awal
Upon initial power-on, the upper LED display will show the current temperature measured by the sensor. The lower LED display will show the currently set 'stop temperature'.
5.2. Butang Kawalan
- Butang MENU: Used to cycle through and select different settings (stop temperature, start temperature, anti-freeze function). Pressing this button allows you to enter the setting mode for each parameter.
- UP Arrow Button (▲): Used to increase the value of a selected parameter.
- DOWN Arrow Button (▼): Used to decrease the value of a selected parameter.
5.3. Setting Temperature Parameters
- Tekan ke MENU button to enter the setting mode. The lower display will start flashing, indicating you can adjust the 'stop temperature'.
- Gunakan ATAS (▲) dan TURUN (▼) arrow buttons to set the desired temperature at which the pump should stop.
- Tekan ke MENU button again to confirm the 'stop temperature' and move to the 'start temperature' setting. The lower display will flash again.
- Gunakan ATAS (▲) dan TURUN (▼) arrow buttons to set the desired temperature at which the pump should start. This is typically a few degrees higher than the stop temperature to prevent rapid cycling.
- Tekan ke MENU button a third time to confirm the 'start temperature' and exit the setting mode. The controller will return to displaying the current and stop temperatures.
5.4. Fungsi Anti-beku
The anti-freeze function is automatically engaged. If the temperature measured by the sensor drops below 5 °C (41 °F), the pump will activate regardless of other settings to circulate water and prevent freezing. This function cannot be manually disabled.
6. Penyelenggaraan
The IBO S-150 controller requires minimal maintenance to ensure optimal performance and longevity.
- Pembersihan: Periodically wipe the exterior of the controller with a soft, dry cloth. Do not use abrasive cleaners or solvents. Ensure no liquids enter the device.
- Pemeriksaan Kabel: Regularly check all connected cables (power, pump, sensor) for any signs of wear, damage, or loose connections. Replace damaged cables immediately.
- Peletakan Sensor: Ensure the temperature sensor remains securely in its intended position and maintains good thermal contact with the heating system pipe.
- Keadaan Persekitaran: Verify that the controller's operating environment remains within the specified ambient temperature and humidity ranges.
7. Penyelesaian masalah
If you encounter issues with your IBO S-150 controller, refer to the following troubleshooting guide:
| Masalah | Kemungkinan Punca | Penyelesaian |
|---|---|---|
| Pengawal tidak dihidupkan. | No power supply; loose power cable; faulty outlet. | Check power outlet; ensure power cable is securely plugged in; check circuit breaker. |
| Pump does not turn on when temperature is high. | Incorrect 'start temperature' setting; faulty pump connection; pump malfunction. | Verify 'start temperature' setting; check pump power cable connection; test pump independently if possible. |
| Pump does not turn off when temperature is low. | Incorrect 'stop temperature' setting; sensor malfunction. | Verify 'stop temperature' setting; check sensor connection and placement. |
| Bacaan suhu tidak tepat. | Sensor improperly placed; faulty sensor. | Ensure sensor has good thermal contact and is correctly positioned; replace sensor if necessary. |
| Anti-freeze function activates unexpectedly. | Ambient temperature near or below 5 °C; sensor reading error. | This is normal operation if ambient temperature is low. Check sensor reading for accuracy. |
If the problem persists after attempting these solutions, please contact a qualified technician or the product support.
8. Waranti dan Sokongan
Untuk maklumat jaminan dan sokongan teknikal, sila rujuk dokumentasi yang disediakan bersama pembelian anda atau hubungi peruncit anda. Simpan bukti pembelian anda untuk sebarang tuntutan jaminan.
Manufacturer: IBO
Nombor Model: S-150
