IBO OHI 25-60/180 Circulation Pump User Manual

1. Produk Lebihview

The IBO OHI 25-60/180 circulation pump, also known as a heating pump, facilitates the movement of heating water within a heating system. This pump model features a manual 3-speed regulator, allowing for system adaptation. It is suitable for use in heating and air conditioning systems with fluid temperatures ranging from +2°C to +110°C.

Ciri-ciri utama termasuk:

• Manual 3-speed regulator for optimal system adaptation.
• Suitable for heating and air conditioning systems with fluid temperatures from +2°C to +110°C.
• Constructed with a ceramic shaft, graphite radial bearing, stainless steel bearing plate and rear pot, and a grey cast iron pump housing.
• Reka bentuk padat untuk pemasangan mudah.
• Operasi yang tenang.

Image 1: IBO OHI 25-60/180 Circulation Pump. This image displays the orange-colored pump unit with its black control panel, showing the speed selector and technical specifications. Two black rubber seals are visible at the bottom.

2. Maklumat Keselamatan

Baca semua arahan dengan teliti sebelum pemasangan dan pengendalian. Kegagalan mematuhi arahan ini boleh mengakibatkan renjatan elektrik, kebakaran atau kecederaan serius.

• Keselamatan Elektrik: Ensure the power supply is disconnected before any installation, maintenance, or repair work. All electrical connections must be performed by a qualified electrician in accordance with local regulations. The pump requires a 230V, 50Hz power supply.
• Suhu Air: The pump handles fluid temperatures between +2°C and +110°C. Exercise caution when working with hot water to prevent burns.
• Tekanan: The maximum operating pressure is 10 bar. Ensure the system components can withstand this pressure.
• Persekitaran Pemasangan: Install the pump in a dry, well-ventilated area, protected from frost and direct weather exposure.
• Peralatan Pelindung Diri: Always wear appropriate personal protective equipment (e.g., gloves, safety glasses) during installation and maintenance.

3. Panduan Pemasangan

Proper installation is crucial for the pump's efficient and safe operation.

3.1 Pemeriksaan Pra-Pemasangan

• Verify that the pump's specifications (voltage, frequency, pressure) match your system requirements.
• Ensure the installation location provides adequate space for mounting and future maintenance.
• Confirm that the piping system is clean and free of debris.

3.2 Memasang Pam

1. The pump has an installation length of 180 mm. Ensure sufficient space between pipe connections.
2. Install the pump in the return line of the heating system, if possible, to extend its lifespan by operating at lower temperatures.
3. Ensure the motor shaft is horizontal to allow for proper lubrication of the bearings.
4. Use the provided seals (gaskets) to ensure a watertight connection to the piping. The connection diameter is 1 1/2"/1".
5. Tighten all connections securely but avoid over-tightening.

3.3 Sambungan Elektrik

1. Pastikan bekalan kuasa utama dimatikan pada pemutus litar.
2. Connect the pump to a 1 x 230 V, 50 Hz power supply.
3. The pump has an IP44 protection rating. Ensure the electrical connections are protected from moisture.
4. Follow the wiring diagram provided on the pump's terminal box cover.
5. Pastikan pembumian yang betul.

3.4 System Filling and Venting

1. After installation, fill the heating system with water.
2. Vent the system thoroughly to remove any trapped air. Air in the system can cause noise and reduce pump efficiency.
3. The pump may have a manual vent screw; open it carefully until water flows out, then close it.

4. Arahan Operasi

The IBO OHI 25-60/180 pump features a manual 3-speed selector to adjust performance.

4.1 Permulaan Permulaan

1. Ensure the system is filled with water and properly vented.
2. Turn on the main power supply to the pump.
3. Select a speed setting using the rotary switch on the pump's control panel.

4.2 Tetapan Kelajuan

The pump offers three speed levels, each with different power consumption, maximum flow rate (Q max), and maximum head (H max):

• Tahap I: 46 W power consumption, 22 l/min maximum flow, 3 m maximum head.
• Tahap II: 63 W power consumption, 38 l/min maximum flow, 5 m maximum head.
• Tahap III: 93 W power consumption, 55 l/min maximum flow, 6 m maximum head.

Adjust the speed setting based on the heating system's requirements to achieve optimal circulation and energy efficiency.

5. Penyelenggaraan

Regular maintenance ensures the longevity and efficient operation of your circulation pump.

5.1 Pemeriksaan Rutin

• Pemeriksaan Visual: Periksa pam secara berkala untuk sebarang tanda kebocoran, kakisan atau kerosakan pada pam.asing atau sambungan elektrik.
• Tahap Bunyi: Listen for any unusual noises during operation, which could indicate air in the system or a mechanical issue.
• Suhu: Ensure the pump is not overheating.

5.2 Pembersihan

Keep the exterior of the pump clean and free from dust and debris to ensure proper heat dissipation.

5.3 Musim sejuk (jika berkenaan)

If the heating system is to be shut down for an extended period in freezing temperatures, ensure the system, including the pump, is drained to prevent frost damage.

6. Penyelesaian masalah

Bahagian ini menyediakan panduan untuk isu biasa. Untuk masalah yang rumit, rujuk juruteknik bertauliah.

7. Spesifikasi Teknikal

8. Waranti dan Sokongan

Information regarding the product warranty is not provided in the available data. For warranty claims, technical support, or spare parts inquiries, please contact the original seller or the manufacturer, 4U-Onlinehandel, directly. Keep your purchase receipt as proof of purchase.