HP ProLiant DL360 G9 1U Rack Server User Manual

pengenalan

This manual provides essential information for the safe and efficient use of your HP ProLiant DL360 G9 1U Rack Server. It covers installation, operation, maintenance, and troubleshooting procedures. Please read this manual thoroughly before operating the server and retain it for future reference.

Maklumat Keselamatan

Patuhi langkah berjaga-jaga keselamatan berikut untuk mencegah kecederaan dan kerosakan pada peralatan:

• Pastikan pembumian yang betul untuk semua sambungan elektrik.
• Do not operate the server with covers removed unless specifically instructed for maintenance.
• Disconnect all power cords before performing any service or upgrade procedures.
• Use only approved power supplies and cables.
• Install the server in a well-ventilated area to prevent overheating.
• Avoid spilling liquids on the server.

Kandungan Pakej

Sahkan bahawa semua item terdapat dalam pakej:

• HP ProLiant DL360 G9 1U Rack Server
• Rack mounting hardware kit
• Kord kuasa
• Dokumentasi (manual ini, maklumat waranti)

Note: Specific components may vary based on configuration.

Produk Selesaiview

The HP ProLiant DL360 G9 is a 1U rack-optimized server designed for high-performance computing and data center environments. It features dual Intel Xeon E5-2670 v3 processors, offering robust processing capabilities.

Panel Depan

This image displays the front panel of the HP ProLiant DL360 G9 server, highlighting the drive bays, power button, and status indicators. The drive bays are accessible from the front for easy hot-swapping of storage devices.

Panel Belakang

This image shows the rear panel of the HP ProLiant DL360 G9 server, detailing the various I/O ports, network interfaces, and redundant power supply units. All essential connections for power, network, and peripheral devices are located here.

Persediaan

1. Pemasangan Rak

1. Attach the rack rails to the server chassis using the provided hardware.
2. Mount the server into a standard 19-inch server rack, ensuring it is securely fastened.
3. Verify that there is adequate space for airflow around the server.

2. Sambungan Kuasa

1. Connect the power cords to the server's power supply units.
2. Plug the other end of the power cords into grounded electrical outlets or a power distribution unit (PDU).
3. Ensure power sources provide 240 Volts as specified.

3. Sambungan Rangkaian

1. Connect Ethernet cables from your network infrastructure to the server's network ports.
2. For remote management, connect a dedicated Ethernet cable to the iLO port.

4. But Awal

1. Tekan butang kuasa pada panel hadapan.
2. Observe the POST (Power-On Self-Test) sequence.
3. Access the BIOS/UEFI setup if necessary to configure boot options or hardware settings.

Arahan Operasi

Menghidupkan/Mematikan

• Untuk Menghidupkan: Tekan butang kuasa pada panel hadapan.
• Untuk Mematikan: Perform a graceful shutdown through the operating system. If unresponsive, press and hold the power button for 5 seconds for a forced shutdown.

Accessing BIOS/UEFI

During the server's boot sequence, press the designated key (typically F9 or Padam) to enter the BIOS/UEFI setup utility. Refer to the on-screen prompts for the exact key.

Pemasangan Sistem Operasi

Install your preferred operating system (e.g., Windows Server, Linux) using a bootable USB drive, optical drive, or network installation. Configure RAID arrays as needed before OS installation.

Remote Management (iLO)

The integrated Lights-Out (iLO) port allows for remote management of the server. Access the iLO web antara muka melalui a web browser using the IP address assigned to the iLO port. Default credentials are typically found on a pull-out tag on the server chassis.

Penyelenggaraan

Pembersihan

• Regularly clean dust from air vents and fan grilles using compressed air.
• Wipe exterior surfaces with a soft, dry cloth. Do not use liquid cleaners directly on the server.

Kemas kini Perisian Tegar

Periodically check the HP support website for firmware updates for the BIOS, iLO, and other server components. Apply updates as recommended to ensure optimal performance and security.

Penggantian Komponen

For replacing components such as hard drives, memory modules, or power supplies, refer to the specific service manual available on the HP support website. Always power down the server and disconnect power cords before opening the chassis for component replacement.

Menyelesaikan masalah

This section provides solutions for common issues. For more complex problems, consult the HP support webtapak atau hubungi sokongan teknikal.

• Server does not power on: Check power cord connections, power supply status indicators, and ensure the power button is fully pressed.
• Tiada output video: Verify monitor connection, try a different display cable, or check for POST error codes.
• Operating system fails to boot: Check boot order in BIOS/UEFI, verify hard drive status, or attempt OS repair.
• Overheating warnings: Ensure proper ventilation, clean dust from fans, and check ambient room temperature.
• Isu sambungan rangkaian: Verify Ethernet cable connections, check network adapter drivers, and confirm network configuration.

Spesifikasi

Waranti dan Sokongan

This HP ProLiant DL360 G9 server is covered by a standard manufacturer's warranty. For detailed warranty terms and conditions, please refer to the warranty documentation included with your product or visit the official HP support webtapak.

For technical assistance, driver downloads, and additional support resources, please visit the Sokongan HP Webtapak. When contacting support, please have your server's model number (795236-B21) and serial number readily available.