GX उपकरणांसाठी व्हिक्ट्रॉन एनर्जी GX IO-एक्सटेंडर १५० वर्धित इनपुट आणि आउटपुट

परिचय
GX IO-Extender 150 हे एक USB-कनेक्टेड एक्सपेंशन मॉड्यूल आहे जे Ekrano GX आणि Cerbo GX सारख्या GX उपकरणांच्या उपलब्ध IO पोर्टचा विस्तार करते.
हे तुमच्या GX डिव्हाइस आणि बाह्य जगामधील अंतर कमी करते, देखरेख, नियंत्रण आणि ऑटोमेशनसाठी अनंत शक्यता निर्माण करते.

वैशिष्ट्ये

• 8 digital IOs, configurable as in two sets of four as inputs or outputs (via DIP switch).
• 4 PWM ports, 0 to 5V with 0.04V steps for device regulation.
• 2 latching relays that maintain their state even if the power is lost.
• 1 solid switch with bat-, load, and bat+ connections for switching requirements.

The plug-and-play USB connectivity makes installation effortless. The GX IO-Extender 150 is simply plugged into an available USB port on the GX device and the inputs/outputs, PWMs and relays immediately become available to the system.
Whether you’re managing a complex off-grid solar installation, a marine electrical system, or an industrial backup power solution, the GX IO-Extender 150 expands your ability to deliver on specific requirements:

• Monitor additional sensors and equipment
• Control external devices with precision
• Automate complex system responses
• Implement sophisticated control logic

The GX IO-Extender is not intended to be used for general load switching, but rather for signalling. The relays and solid switch have low current ratings that vary based on the voltage वापरला जात आहे. एनर्जी सोल्युशन्स (यूके), गार्मिन (यूएसए) आणि सेफियरी आणि इतर मधील सुसंगत उत्पादने सामान्य स्विचिंग अनुप्रयोगांसाठी अधिक योग्य असतील.

Relay and Solid Switch specifications

लॅचिंग रिले
Contact rating (resistive load):

• DC: 3 A @ 30 V, 1 A @ 60 V, 0,3 A @ 220 V (max. 90 W)
• AC: 2 A @ 60 V, 1 A @ 125 V, 0,5 A @ 250 V (max. 125 VA)

Solid Switch

• कमाल बॅटरी व्हॉल्यूमtage: 70 VDC
• कमाल लोड करंट: 4 ए
• Max. capacitive load:
  • Vbat up to 15 V: 1000 µF
  • 15 V < Vbat < 30 V: 400 µF
  • 30 V < Vbat < 70 V: 50 µF
• कमाल प्रेरक भार:
  • Up to 1 A: 1000 mH
  • 1 A < I < 2 A: 100 mH
  • More than 2 A: 10 mH

स्थापना

The GX IO-Extender 150 works with all GX devices but it is best used in combination with Node-RED. Node-RED is not supported on all GX devices. Refer to the Venus OS Large documentation for more information about which GX devices support Node-RED.
To install the GX IO-Extender 150:

1. Use the DIP switches on each bank of 4 digital I/Os to set them as 4 inputs or 4 outputs (ON = output, OFF = input). Note that changes to the DIP switches require a power cycle of the device.
2. Connect the USB cable of the GX IO-Extender 150 to an available port on the GX device. Note that the USB-port closest to the HDMI port on some Cerbo GX models may not be suitable for this purpose. Please refer to the GX device manual for more information.
3. Confirm the GX IO-Extender 150 is powered via the USB connection.
4. पुन्हा करण्यासाठी GX वरील रिमोट कन्सोल वापराview सिस्टमवर उपलब्ध असलेले अतिरिक्त रिले, पीडब्ल्यूएम आणि डिजिटल इनपुट किंवा आउटपुट.

हार्डवेअर
GX IO-Extender 150 वरील सर्व पोर्ट त्यांची सद्यस्थिती दर्शविणारे निळे किंवा नारिंगी LEDs ने सुसज्ज आहेत.

डिजिटल आउटपुट फक्त सिग्नलिंगच्या उद्देशाने आहेत आणि ते थेट लोड स्विच करण्यासाठी वापरले जाऊ नयेत. PWM आउटपुट LED डिमिंग, मोटर स्पीड कंट्रोल आणि तत्सम अनुप्रयोगांसाठी योग्य आहेत.

तांत्रिक टीप: Always check the maximum ratings for each output type in the datasheet of the GX IO-Extender 150.

डिजिटल I/O
The digital I/O ports are split up in 2 groups of 4 ports which are intended for signalling rather than directly switching loads. Each group can be configured as either input or output using the dip switches in between the ports.

• Mode ON = output
• Mode OFF = input

मोड बदलल्यानंतर, बदल प्रभावी होण्यासाठी GX रीबूट करा किंवा डिव्हाइसला पॉवर सायकल करण्यासाठी USB केबल अनप्लग करा आणि पुन्हा प्लग करा.
तांत्रिक टीप: The digital outputs can source 4 mA max. When driving 4 mA, the voltage drop across the internal series resistor (560 Ω) is 2,24 V, which leaves only 2,76 V @ 4 mA for the output signal. Therefore, a driver like a transistor or FET is required to switch a relay with a digital output.

PWM
The PWM ports are to be connected between GND and signal. The PWM port indicator LEDs are illuminated when the port is switched on, and the intensity of the illumination reflects the current status of the PWM slider value.

Bistable Relays (Relay 1 & 2)
The bistable (latching) relays on the GX IO-Extender 150 work differently from the monostable (non-latching) relays found on devices like the Cerbo GX.
A monostable relay has a default state determined by its wiring:

• NO (Normally Open): Load is OFF by default, ON when relay is powered.
• NC (Normally Closed): Load is ON by default, OFF when relay is powered.

A bistable relay has two stable positions — A and B — that stay fixed even when power is lost. The relay switches between them with a short pulse, using no power to maintain either state. The active position is shown by the LED:

• Blue LED: Position A active
• Orange LED: Position B active

सामान्य माजीampलेस

1. Mimicking a NO monostable relay
   To replicate the behaviour of a normally open relay:
   • Connect your power source to COM.
   • Connect your load to Terminal A.
   • Leave Terminal B disconnected.
   • Configure the relay in Toggle mode.
     In position A (blue LED), the load is powered. In position B (orange LED), the load is disconnected.
     जर पॉवर सायकलनंतर लोड बंद असेल, तर बंद होण्यापूर्वी रिले B स्थितीवर सेट करा.
2. Switching between “GREEN” and “RED” indicator lights The relay can switch power between two circuits, for exampले:
   • COM connected to your power source.
   • Terminal A wired to an “GREEN” indicator light.
   • Terminal B wired to an “RED” indicator light.
   • Configure the relay in Toggle mode.
     जेव्हा A स्थितीत (निळा LED) असतो, तेव्हा हिरवा दिवा सक्रिय असतो. जेव्हा B स्थितीत (नारंगी LED) असतो, तेव्हा लाल दिवा सक्रिय असतो.
3. Momentary operation: Siren and “All OK” light For momentary operation with default feedback:
   • COM connected to your power source.
   • Terminal A wired to a siren.
   • Terminal B wired to an “All OK” light.
   • Configure the relay in Momentary mode.

In its resting state (position B, orange LED), the “All OK” light is illuminated. When the momentary switch is activated, it briefly switches the relay to position A, sounding the siren. Once the momentary pulse ends, the relay returns to position B, and the “All OK” light comes back on.

Solid Switch
The solid switch on the GX IO-Extender 150 is designed to electronically switch the positive side of a DC circuit, with no mechanical contacts.

• Bat+ → Connect to the positive terminal of your battery or DC power supply.
• Load → Connect to the positive side of your device or load.
• Bat- → Connect to the negative terminal of your battery or DC power supply.
• The negative side of your load connects directly to Bat- (or a shared ground).
• Configure the relay in Toggle mode.

This setup allows the solid-state relay to switch your load on and off by making or breaking the positive side of the circuit electronically.
If the solid switch is configured as momentary, it will only switch the load on for as long as the control signal remains active.

सॉफ्टवेअर
Node-RED is a low-code programming environment for event-driven applications (https://nodered.org). See the installation manual for more information on the Node-RED and GX device combination: https://www.victronenergy.com/live/venus-os:large.

The following 4 steps are needed to get Node-RED up and running on your system:

1. Set the firmware image type to Large and update the firmware
2. Once rebooted in the large image, enable Node-RED
3. Open the Node-RED dashboard via either VRM under the Venus OS Large menu option or locally via https://venus.local:1881/
4. Pull in the Switch and Switch control node and control the GX IO-Extender 150. These nodes are part of the node-red-contrib-victron package that comes pre-installed with the Venus OS Large image.

हे आणि इतर, उदा.ampनोड-रेडमधील आयात पर्यायाद्वारे ले फ्लो आयात केले जाऊ शकतात.

Simple digital input control
First, the digital input must be configured to a type using the Settings > Integrations > Digital IO on the GX device, then select a digital input from the GX IO-Extender 150 and set a type.

Supported input types are:

• Pulse meter N/A
• Door alarm Open/Closed
• Bilge pump On/Off
• Bilge alarm Ok/Alarm
• Burglar alarm Ok/Alarm
• Smoke alarm Ok/Alarm
• Fire alarm Ok/Alarm
• CO2 alarm Ok/Alarm
• Generator Running/Stopped
• Touch input control

Once an input type has been selected, a Digital input node can be used to read the status of that input for further use in the flow.

या माजीample नोड-रेड डॅशबोर्डमधील गेज वापरून डिजिटल इनपुटवर वाचलेल्या पल्स प्रदर्शित करते.

पीडब्ल्यूएम वाढवा

या प्रवाहाचा वरचा भाग PWM स्टेट पॅरामीटर वापरून PWM पोर्ट चालू किंवा बंद करण्यासाठी आहे. एकदा पोर्ट चालू झाला की, ते PWM डिमिंग पॅरामीटर वापरून सेट केलेले कोणतेही PWM मूल्य वापरेल. इनपुट नोड PWM पोर्टचे वर्तमान मूल्य वाचतो आणि ते जागतिक नोड-रेड संदर्भात संग्रहित करतो.
इंजेक्ट नोड एक टाइमस्ट इंजेक्ट करतोamp प्रत्येक सेकंदाला, जे पोर्टच्या सध्याच्या PWM मूल्याने बदलले जाते, ते २५ ने वाढते. जर मूल्य १०० पेक्षा जास्त असेल, तर ते पुन्हा ० वर रीसेट होते.

लक्षात ठेवा की फंक्शन नोड तुमच्यासाठी कार्यक्षम करण्यासाठी तुम्हाला वापरलेला स्विच आणि PWM पोर्ट समायोजित करावा लागू शकतो.

तांत्रिक वैशिष्ट्ये

GX IO-एक्सटेंडर १५०
पुरवठा खंडtage	USB द्वारे समर्थित
वीज वापर	< 100 mW when idle, max, 1 W (< 200 mA @ 5 V)
आरोहित	Wall or DIN-rail (by using adapter accessory)
Input and Output connectivity
Digital I/Os (isolated from USB)	8 I/Os with LEDs indicating state, configurable as 8 inputs, 8 outputs or 4 inputs + 4 outputs
	Inputs: 3,8 – 5,5 V, Outputs: 5 V, 4 mA max डिजिटल I/Os व्हॉल्यूम हाताळण्यास सक्षम आहेतtag५.५ व्ही पर्यंत. कोणताही ओव्हरव्होलtage कायमचे नुकसान करू शकते
PWM output (isolated from USB)	4 channels with LEDs indicating the state खंडtagई लेव्हल: ५ व्ही, प्रिसिजन: ८ बिट्स @ १,५६२५ kHz
Latching relays (potential free)	स्थिती दर्शविणारे LEDs असलेले 2x लॅचिंग रिले (द्वि-स्थिर)
	Contact rating (resistive load): DC: 3 A @ 30 V, 1 A @ 60 V, 0,3 A @ 220 V (90 W max) AC: 2 A @ 60 V, 1 A @ 125 V, 0,5 A @ 250 V (125VA max)
सॉलिड स्विच (USB पासून वेगळे केलेले)	कमाल बॅटरी व्हॉल्यूमtage:	70 VDC
	कमाल लोड वर्तमान:	२.२ अ
	कमाल कॅपेसिटिव्ह लोड:	Vbat up to 15 V: 1000 µF 15 V < Vbat < 30 V: 400 µF 30 V < Vbat < 70 V: 50 µF
	कमाल प्रेरक भार:	Up to 1 A: 1000 mH 1 A < | < 2 A: 100 mH More than 2 A: 10 mH
परिमाण
बाह्य परिमाणे (hxwxd)	123 x 67 x 23 मिमी
वजन	0,170 किलो
ऑपरेटिंग तापमान श्रेणी	-20°C ते +50°C

परिशिष्ट

Available Control Paths
The device announces itself under the dbus service com.victronenergy.switch.<serial> and exposes the paths as described in this appendix. Check https://github.com/victronenergy/venus/wiki/dbus#switch for the meaning and usage of any additional paths.

डिजिटल इनपुट
Digital inputs need to be coupled to a function first, before you can use them. This needs to be done in the console as described above.

Set the type of a digital input with

• 0 = अक्षम
• 1 = Pulse meter
• 2 = दार
• 3 = Bilge pump
• 4 = Bilge Alarm
• 5 = Burglar Alarm
• 6 = स्मोक अलार्म
• 7 = फायर अलार्म
• 8 = CO2 अलार्म
• 9 = Generator

Pulsemeter paths
/Count: number of counted pulses

Generic digital input paths
/State: State of the input

डिजिटल आउटपुट
Note that these paths will only be present when the corresponding IO is set to output (with the DIP switches).

• /SwitchableOutput/output_1/State (0=Off, 1=On)
• /SwitchableOutput/output_2/State (0=Off, 1=On)
• /SwitchableOutput/output_3/State (0=Off, 1=On)
• /SwitchableOutput/output_4/State (0=Off, 1=On)
• /SwitchableOutput/output_5/State (0=Off, 1=On)
• /SwitchableOutput/output_6/State (0=Off, 1=On)
• /SwitchableOutput/output_7/State (0=Off, 1=On)
• /SwitchableOutput/output_8/State (0=Off, 1=On)

PWM आउटपुट

• /SwitchableOutput/pwm_1/State (0=Off, 1=On)
• /SwitchableOutput/pwm_1/Dimming (integer value from 0-100, representing percentage)
• /SwitchableOutput/pwm_2/State (0=Off, 1=On)
• /SwitchableOutput/pwm_2/Dimming (integer value from 0-100, representing percentage)
• /SwitchableOutput/pwm_3/State (0=Off, 1=On)
• /SwitchableOutput/pwm_3/Dimming (integer value from 0-100, representing percentage)
• /SwitchableOutput/pwm_4/State (0=Off, 1=On)
• /SwitchableOutput/pwm_4/Dimming (integer value from 0-100, representing percentage)

रिले आउटपुट

• /SwitchableOutput/relay_1/State (0=Off, 1=On) – Bi-stable relay 0 = A, 1 = B
• /SwitchableOutput/relay_2/State (0=Off, 1=On) – Bi-stable relay 0 = A, 1 = B
• /SwitchableOutput/relay_3/State (0=Off, 1=On) – Solid switch load state

संलग्न परिमाण

कागदपत्रे / संसाधने

GX उपकरणांसाठी व्हिक्ट्रॉन एनर्जी GX IO-एक्सटेंडर १५० वर्धित इनपुट आणि आउटपुट [pdf] वापरकर्ता मार्गदर्शक GX IO-एक्सटेंडर १५०, GX IO-एक्सटेंडर १५० GX उपकरणांसाठी वर्धित इनपुट आणि आउटपुट, GX उपकरणांसाठी वर्धित इनपुट आणि आउटपुट, GX उपकरणांसाठी इनपुट आणि आउटपुट, GX उपकरणांसाठी आउटपुट, GX उपकरणे

संदर्भ

• वापरकर्ता मॅन्युअल