ANDTE Automatic Condensate Pump (Model ZJ-KBS-4A) Instruction Manual

1. परिचय

This manual provides essential information for the safe and efficient installation, operation, and maintenance of your ANDTE Automatic Condensate Pump, Model ZJ-KBS-4A. This pump is designed to automatically remove condensate water from HVAC/R equipment, air conditioners, and dehumidifiers, ensuring optimal performance and preventing water damage.

2. सुरक्षितता माहिती

Please read all safety instructions carefully before installation and operation.

• कोणतीही स्थापना, देखभाल किंवा समस्यानिवारण करण्यापूर्वी नेहमी वीज खंडित करा.
• Ensure the pump is installed in a location where it is protected from freezing temperatures.
• Do not pump flammable liquids or chemicals. This pump is designed for condensate water only.
• सर्व विद्युत कनेक्शन स्थानिक कोड आणि नियमांचे पालन करत असल्याची खात्री करा.
• The pump is equipped with a water level alarm and automatic shutdown function to prevent overflow. Do not bypass these safety features.
• ऑपरेशन दरम्यान हात आणि परदेशी वस्तू हलत्या भागांपासून दूर ठेवा.

3. उत्पादन संपलेview आणि घटक

The ANDTE Automatic Condensate Pump is a compact and durable unit designed for reliable condensate removal. It features a high-performance motor and an integrated float switch for automatic operation.

आकृती 1: मुख्य view of the ANDTE Automatic Condensate Pump.

Figure 2: Diagram illustrating key specifications and water flow paths (IN/OUT) of the condensate pump.

4. तपशील

Below are the technical specifications for the ANDTE Automatic Condensate Pump, Model ZJ-KBS-4A:

Figure 3: Detailed specifications and physical dimensions of the pump.

5. स्थापना आणि सेटअप

Follow these steps to properly install your condensate pump:

1. प्लेसमेंट: Position the pump on a stable, level surface near the condensate drain outlet of your HVAC unit, air conditioner, or dehumidifier. Ensure it is below the drain outlet to allow gravity flow into the pump.
2. इनलेट कनेक्शन: Connect the condensate drain line from your equipment to one of the 1-inch (0.87-inch universal) inlet ports on the pump. The pump offers multiple inlet options (top/side) for flexible installation. Secure the connection to prevent leaks.
3. आउटलेट कनेक्शन: Connect a 3/8-inch (4mm) discharge tube to the pump's outlet port. Route this tube upwards to the desired drainage location, ensuring it does not exceed the maximum vertical head of 20 feet. Avoid kinks or sharp bends in the tubing.
4. वीज कनेक्शन: Plug the 3.3-foot UL power cord into a standard 115-volt, 60 Hz electrical outlet. Ensure the outlet is properly grounded.
5. चाचणी ऑपरेशन: Once all connections are secure, manually pour a small amount of water into the pump's reservoir to verify that the pump activates, discharges the water, and then shuts off automatically. Check for any leaks.

आकृती 4: उदाample installation showing the condensate pump connected to a dehumidifier, with the discharge line routing water upwards.

6. ऑपरेटिंग सूचना

The ANDTE Automatic Condensate Pump operates automatically based on the water level in its reservoir:

• When condensate water from your equipment flows into the pump's reservoir and reaches approximately 2.28 inches, the built-in float switch will activate the pump.
• The pump will then efficiently discharge the water through the connected outlet tube.
• Once the water level drops to approximately 1.26 inches, the float switch will automatically shut off the pump.
• This automatic cycle ensures continuous and reliable condensate removal without manual intervention.

7. देखभाल

Regular maintenance is crucial for the longevity and efficient operation of your condensate pump. Perform the following maintenance tasks every 6 months:

• पॉवर डिस्कनेक्ट करा: Always unplug the pump from the power outlet before beginning any maintenance.
• Clean Liquid Storage Tank: Carefully remove the pump cover and detach the liquid storage tank. Clean the inside of the tank to remove any sludge, mold, or debris that may have accumulated. Use mild soap and water, then rinse thoroughly.
• Clean Float Ball: Remove the float ball and clean it to ensure it moves freely without obstruction. Any buildup on the float can prevent proper activation or deactivation of the pump.
• फिल्टर टाकी स्वच्छ करा: If your model includes a separate filter tank, clean it as well to ensure unrestricted water flow.
• ट्यूबिंग तपासा: Check the inlet and outlet tubing for any blockages, kinks, or signs of wear. Clear any obstructions.
• पुन्हा एकत्र करा आणि चाचणी करा: Reassemble all components, ensuring they are securely in place. Plug the pump back in and perform a test run by pouring water into the reservoir to confirm proper operation.

8. समस्या निवारण

If you encounter issues with your condensate pump, refer to the table below for common problems and solutions:

9. अनुप्रयोग

The ANDTE Automatic Condensate Pump is suitable for a variety of applications requiring efficient condensate removal:

• डेहुमिडिफायर्स
• Air Conditioners (including embedded and wall-mount portable AC units)
• व्यावसायिक बर्फ निर्माते
• बॉयलर

Figure 5: Multiple applications for the ANDTE Automatic Condensate Pump, including dehumidifiers, air conditioners, and ice makers.

10. हमी आणि समर्थन

ANDTE is committed to providing reliable products and customer satisfaction. While specific warranty details for this pump are not explicitly stated, ANDTE generally offers comprehensive support for its products.

• सामान्य हमी माहिती: ANDTE products typically come with a 5-year limited coverage, including 1-year full coverage.
• रिटर्न पॉलिसी: A 30-day money-back guarantee is often provided.
• ग्राहक समर्थन: ANDTE aims to provide timely responses to customer inquiries, often within 12 hours.

For specific warranty claims, technical assistance, or any questions regarding your ANDTE Automatic Condensate Pump, please refer to the contact information provided with your purchase or visit the official ANDTE webसाइट