Mounting Dream Height Adjustable Speaker Stands Mounts, One Pair Floor Stands-Complete Features/Instruction Guide

Mounting Dream is committed to producing and designing high-quality and reasonably priced TV accessories. Each mount is made to keep your device secure and flexible for optimal viewing. We’re dedicated to providing items like universal TV mounts, soundbar brackets, lockable RV TV mounts, TV covers, speaker stands, screws kit, and other accessories.

Safety Warning

Thank you for choosing the Mounting Dream Speaker stand. For the safe application of model MD5401, and to prevent yourself or others from danger or property loss, please read through this manual before use. If you do not understand these instructions or have any doubt over the safety of an installation, please contact a qualified contractor or Mounting Dream customer service. Please check carefully before assembly to ensure no parts are missed or damaged. Our customer service representative will assist you timely in installation to solve the issue of parts shortage or damage. Replacement parts purchased through an authorized distributor will be delivered to your door. Please do not use defective parts. Incorrect installation may result in product damage or bodily injury. Do not apply this product to any purpose not indicated by Mounting Dream. We shall bear no responsibility for any damage or injury resulting from incorrect installation, incorrect assembly, or misuse.

Installation tools (Not Included)

Part list

Hardware for stand assembly

Hardware for speaker assembly

Step 1
Attach fixed tube (B) to base (A), assemble adjusting tube (C) to connecting tube (D) by loosening/tightening the plastic nut (Figure 1). Then attach the assembled unit to the fixed tube (B) by fastening knob screw (K) (Figure 2).

Step 2
Insert the Speaker attachment unit (J) into the adjusting tube (C) and fasten it by bolt (H) (Figure 3).

Step 3
Attach the speaker to assembled stand

Option 1
The Speaker installation hole distance is below 166mm/6.5in from the bottom

According to your speaker’s installation hole, choose bolt L/M/N, spacer (R), and plastic washer (S) ( as Figure 4 and Figure 5 show) to attach it . Then plug the wires.

Option 2 Speaker with a keyhole

Attach key hole bolt (O) to the assembled iron wire with plastic washer (S) and nut (I3).

Place speaker on connection base with keyhole bolt (O) inserted in the keyhole, then tighten the round nut (I3) and plug the wires.

Option 3 Speaker with two parallel installation holes

Assemble horizontal bar (I1) to the assembled iron wire with washer (I2) and nut (I3).

According to your speaker’s installation holes, choose bolt L/M/N, plastic washer (S) , washer P/Q and spacer (R) ( as shown in Figure 6, Figure 7, Figure 8, Figure 9 ) to attach it. Then plug the wires

Option 4 Speaker with a wooden base and has no installation holes at all.

Use wood screws (NOT provided in the package) to mount the speaker. Mark holes on the bottom of the speaker and drill holes, attach the speaker to the speaker stand.

Height adjustment

Adjust the speaker stand to the desired height by unscrewing and extending the adjusting tube(C).

Product dimensions

Frequently Asked Questions

The keyhole is little under 8 in. if you measure from the bottom to top, will I be able to mount these? Does this item come with screws that fit the keyhole?
Thank you for your interest and contact us regarding the Mounting Dream Stands. We understand and we’re glad to help. Yes, the MD5401 is perfectly compatible with 8″ inches height also using the keyhole hardware to help complete the installation.
Does anyone know the inside diameter of the tube to route the speaker cable?
Thank you for your interest and contact us regarding the Mounting Dream Stand. We understand and we’re glad to help. The MD5401 diameter of inside is 11/16″ inches since the outside is 3/4″ inches.
How many stands are in the package ? are they sold in pairs?
Mounting Dream Mounts. We understand and we’re glad to help. The MD5401 package is sold in pairs.
Can you attach a speaker that has a hole in the middle of the bottom of it? Can a hole be drilled in the plate if needed?
The plate comes with a hole already drilled on it. You just need to use your speaker bolt.
Will these fit Polk audio tsi100 bookshelf speakers? i am not sure of the height of the keyhole on the speakers they are on order
We understand and we’re glad to help. Unfortunately no, the TSI100 bookshelf speakers are approximately 11″ inches tall which requires the keyhole to be bolted on top which the MD5401 can only extend up to 8″ inches maximum height.
Do the stands work with Bose 321 speakers?
I don’t know about Bose speakers but these stands are set up for adaptability. The speakers I use belong to a Samsung system and they have a mounting screw hole in the back of the speaker and on the bottom. The base is approximately 3″ in diameter so I set the speaker bottom on the base and used the back screw hole to secure the speaker to the stand. Works great for me. This is a very sturdy stand
Hi. will the right-angle power cord plug of the Samsung swa 9500s fit through the hole?
No, it won’t go through the hole, you can run the cable outside and use black cable tights or cut the cable about four feet from the plug and splice it at the bottom of the stand,
If I put 2 corners (1 side) of the base against a wall and push my sofa against the pole, how much space will there be between the wall and sofa?
. We understand and we’re glad to help. The height of the base of MD5401 is 50mm. If there is space higher than 60mm, under your sofa to hide some part of the base, the distance between the wall and sofa is about 140mm. And if there is no space under your sofa to hide the base, the distance will be about 200mm.
Will these stands fit the satellite speakers for the vizio sb3651-e6b 5.1?
Mine are hooked up to a Vizio System – SB3651. So I can tell you yes it does. You just have to select the correct attachments. However, what I encountered is that the jack plugs into the speaker cannot be fed through the speaker stand as the hole in the stand is too small. Neither can the end that connects to the subwoofer. You just have to let it hand off stand and try your best to wrap it up or conceal it. I hope that helps.
What’s the diameter of the circular base that the speakers sit on?
We understand and we’re glad to help. The MD5401 current speaker base is approximately 3.25″ inches in diameter. If you should have any additional questions/concerns, please feel free to let us know anytime.
Will these hold Klipsch pro media 3.1 speakers?
We are sorry to tell you that our MD5401 requires rear holes for installation, but we notice that your speakers have no rear holes for installation.

View Fullscreen

References

User Manual

Mounting Dream Height Adjustable Speaker Stands Mounts, One Pair Floor Stands

Specifications

Introduction