DCP501-R Universal Remote Control
“
Specifications:
- Model: DCP501
- Remote Control Model: DCP501-R Universal Remote Control
Product Information:
The DCP501 uses the DCP501-R Universal Remote Control for
operation. The remote control features various buttons and
functions to control different sources and modes.
Remote Control Functions:
| Button | Item | Description |
|---|
Using the Remote Control:
To operate the DCP501 using the remote control, follow these
steps:
1. Selecting Source:
Use the corresponding buttons (DVD/CD, CATV, VCR1, VCR2, etc.)
to select the desired source for playback.
Use the cursor keys for on-screen display and control. Navigate
menus and options using the cursor keys.
3. Adjusting Audio:
Use the VOL button to raise or lower speaker levels. Use the
MUTE button to mute the audio output as needed.
FAQ:
Q: How do I switch between different modes using the remote
control?
A: When you press a button on the remote control, a mode button
will turn on to indicate the current mode.
Q: How can I adjust the audio settings on the DCP501?
A: You can adjust the speaker levels using the VOL button and
mute the audio using the MUTE button on the remote control.
“`
Overview
15
Operating the Remote Control
The DCP501 uses the DCP501-R Universal Remote Control. Figure 6 illustrates the DCP501-R Universal Remote Control:
Figure 6 Remote control
1
24
2
25
3
26 27
4
28
5
29
30
6
31
32 7
8
33
9
34
10
35
11
36
12
37
13
38
14
39
15
16
40 41
17
42
18
43
19
44
45
20
46
21
47
22
48
23
49
DCP501 User Guide
16
Overview
Descriptions of the remote control functions are shown in the following table.
When you press a button on the remote control, a mode button (CATV, DVD/CD,VCR1, VCR2, Tape, AM/FM, TV, V1 or V2) will turn on to indicate the current mode.
Button
Item
Description
1
SETUP
Press Once: DCP501 A/V configuration menus.
2
DVD/CD
Select DVD/CD as source. (Remote control remains in tuner mode.)
3
CATV
Select Cable TV as source.
4
VCR2
Select VCR 2 as source. Select VCR 2 remote control button codes.
5
VCR1
Select VCR 1 as source. Select VCR 1 remote control button codes.
6
PAGE S
CATV application controlled.
7
Cursor keys Any DCP501 source: DCP501 display/on-screen display and CATV application
control.
TV source: Move cursor up/down/left/right.
VCR 1 or VCR 2 source: Move cursor up/down/left/right.
8
HELP
Press once: CATV application controlled. (The CATV button does not turn on.)
9
GUIDE
CATV application controlled.
10
LAST
CATV application controlled.
11
VOL
Raise or lower speaker level.
12
MUTE
Any DCP501 source: mute speaker and pre-amplifier outputs.
TV source: mute speaker output .
13
A
CATV application controlled.
14
B
CATV application controlled.
15
NIGHT
Press once: DIM mode
DCP501 display dims and audio plays at maximum dynamic range.
Press twice: DIM+SOFT mode
DCP501 display dims and audio plays at minimum dynamic range.
Press three times: DIM+LOUD mode
DCP501 display dims and audio plays at standard dynamic range.
Press four times: NORMAL mode
DCP501 display is not dimmed and audio plays at maximum dynamic
range.
16
Cable TV source: CATV application controlled.
DVD/CD source: Press once (in playback): stop playback (resume possible). Press twice (in playback): stop playback. Press once (not in playback): open DVD/CD tray. Press once (tray open): close DVD/CD tray.
VCR 1 or VCR 2 source: Press once (in playback): stop playback. Press once (not in playback): eject VHS cassette.
DCP501 User Guide
Overview
17
Button 17
18
19 20 21 22 23 24 25 26 27 28 29 30 31
Item TUNE T
FM MODE
INPUT/TV/VCR A-B
SHUFFLE PROG CLEAR POWER AM/FM TV TAPE V1 V2 LOCK
PAGE
Description
Cable TV source: CATV application controlled.
DVD/CD source:
Press once: rewind and play (rewind 1). Press twice: rewind and play (rewind 2). Press three times: rewind and play (rewind 3). Press four times: rewind and play (rewind 4 for DVD only). Press again: rewind and play (rewind 1). Tuner source:
Press to decrease radio tuner frequency Momentarily hold to scan to previous strongest signal (station). Press again to stop scanning. VCR 1 or VCR 2 source: Rewind and play cassette (in playback) or rewind cassette (not in playback).
Cable TV source: CATV application controlled. Tuner source:
Press once: force FM station to mono Press twice: return to normal VCR 1 or VCR 2 source: one touch record, start VCR record.
In playback: Press to select previous chapter (track)
DVD/CD playback: Press once: Select start of sequence for repeat play. Press twice: Mark end of sequence and begin sequence playback.
CD source: Press once: shuffle current CD tracks
Press Once: program DVD/CD playback list (on-screen display) Press Twice: program CD playlist on DCP501 display
In playback: clear A-B, Shuffle, Repeat, or Program playback modes and resume normal mode. Not in playback: clear A-B, Shuffle, Repeat, or Program playback modes.
Place DCP501 in standby mode. Turns power off/on on TV, VCR 1, VCR 2, Video 1 and Video 2 units.
If Tuner not source: selects Tuner as source Tuner source: change radio band (AMFM, FMAM)
Select TV remote control button codes. Remote control will be in TV mode. Note that pressing the TV button will not affect the current mode of the DCP501.
Select Tape as source.
Select Video 1 as source. Select Video 1 remote control button codes.
Select Video 2 as source. Select Video 2 remote control button codes.
CATV application controlled.
CATV application controlled.
DCP501 User Guide
18
Overview
Button 32 33 34 35
36 37 38 39 40 41 42
43 44
Item OK
EXIT INFO MENU
CH
FAVORITE C
Number keys ENTER/ MUSIC DAY
TUNE
Description
Any DCP501 source: select current item on DCP501 display/on-screen display or select CATV application controlled item. TV source: Functions as ENTER key. VCR 1 or VCR 2 source: Functions as ENTER key.
Cable TV source: exit a menu screen or program guide. TV source: exit menu. VCR 1 or VCR 2 source: exit menu.
CATV source: CATV Application controlled.
DVD/CD source: Display DVD/CD information banners.
Cable TV source: CATV application controlled. DVD/CD source: DVD menu. TV Source: TV menu. VCR 1 or VCR 2 source: VCR menu.
Cable TV source: CATV application controlled. Tuner source: Go to next + or previous stored preset station. TV source: Go to next + or previous channel. VCR 1 or VCR 2 source: Go to next + or previous channel.
CATV application controlled.
CATV application controlled.
Number entry.
CATV application controlled. Any non-DCP501 source: Functions as ENTER key.
Cable TV source: CATV application enabled. DVD/CD source: Begin/resume playback (if DVD/CD tray closed). Close tray and begin playback (if DVD/CD tray open). VCR 1 or VCR 2 source: Begin playback.
Cable TV source: CATV application enabled. DVD/CD source:
Press once: fast forward and play (fast forward 1). Press twice: fast forward and play (fast forward 2). Press three times: fast forward and play (fast forward 3). Press four times: fast forward and play (fast forward 4 for DVD only). Press again: fast forward and play (fast forward 1). Tuner source: Press to increase radio tuner frequency Momentarily hold to scan to next strongest signal (station). Press again to stop scanning. VCR 1 or VCR 2 source: Fast forward and play cassette (in playback). Fast forward cassette (not in playback).
Cable TV source: CATV application controlled. DVD/CD source:
Press once: pause playback. Press twice: frame advance (DVD only). In playback: Select next chapter (track).
DCP501 User Guide
Overview
19
Button 45 46
47
48 49
Item DISC SKIP
TONE
REPEAT
AUDIO MODE ANGLE
Description
Not used on the DCP501.
Press once: enter Bass Level Change mode. Press twice: enter Treble Level Change mode. Press three times: enter Balance Level Change mode. Press four times: enter Fader Level Change mode.
DVD/CD playback: Press Once: repeat playback of current disc. Press Twice: repeat playback of current title/track. Press Three Times: repeat playback of current chapter (DVD only). Press Again: clear the repeat function.
Select surround sound mode (toggle through all available modes).
DVD/CD source: Change DVD camera angle (if supported by disc).
Selecting TV and VCR Setup Codes
You can set up your remote control for your TV and VCR by consulting the tables in “TV and VCR Setup Codes”. You only need to set up your remote control for your TV, VCR 1 and VCR 2 (if applicable).
To set up your remote control for your TV or VCR(s):
1 Press the mode button for the device you are setting up (either TV, VCR 1 or VCR 2) for six seconds.
The mode buttons will turn on and turn off one at a time. This sequence will repeat two times and then the selected mode button will remain on. This indicates the remote is ready to accept the four-digit setup code.
2 Enter the four-digit setup code for your TV or VCR. The setup code can be found in “TV and VCR Setup Codes”.
When the setup code is accepted, the selected mode button will blink three times.
If the setup code is not accepted or more than ten seconds have elapsed between button presses, the selected mode button turns off. The TV or VCR then exits the programming mode and the most recent pre-programmed setup code is restored.
You can only set up your remote control while in TV, VCR 1 or VCR 2 mode.
You can exit the setup mode at any time by pressing any button on the remote other than the number buttons.
DCP501 User Guide
20
Overview
Verifying a Setup Code Using Blink Back
You can use the remote control’s blink back function to verify a previously entered setup code. The blink back function verifies a setup code by indicating the setup code number through a certain number of blinks on the 1, 2, 3, and 4 buttons on your remote control.
To verify a setup code using blink back:
1 Press the mode button for the device you are verifying (either TV, VCR 1 or VCR 2) for six seconds.
The mode buttons will turn on and turn off one at a time. This sequence will repeat two times and then the selected mode button will remain on. This indicates the remote is ready to accept the blink back code.
2 Press 9 9 0 on your remote control.
The selected mode button will blink three times and turn off.
3 Press 1 on your remote control. The 1 button will blink for a certain number of times.
The number of blinks that occur after pressing the number buttons represent the four-digit setup code for the selected mode. The 1 button represents the first digit in the setup code, the 2 button represents the second digit in the setup code, and so on for all four digits in the setup code.
For example, to verify the TV setup code is 0047, after you press the mode button and 9 9 0, pressing the 1 button will cause it to remain off, pressing the 2 button will cause it to remain off, pressing the 3 button will cause it to blink four times, and pressing the 4 button will cause it to blink seven times.
4 Press 2 on your remote control and count the number of blinks.
5 Press 3 on your remote control and count the number of blinks.
6 Press 4 on your remote control and count the number of blinks.
You can only set up your remote control while in TV, VCR 1 or VCR 2 mode.
After pressing the mode button and 9 9 0 sequence, you can exit the blink back mode at any time by pressing any button on the remote other than the 1 button.
DCP501 User Guide
Overview
21
Finding a Setup Code
Setup codes for your TV and VCR are listed by brand in “TV and VCR Setup Codes”.
If the setup code for your brand of TV or VCR is not listed, or if your TV or VCR does not respond to the setup codes listed for its brand, you can search for your setup code using your remote control’s Step and Set function.
To search for a setup code:
1 Press the mode button for the device (either TV, VCR 1 or VCR 2) for six seconds.
The mode buttons will turn on and turn off one at a time. This sequence will repeat two times and then the selected mode button will remain on. This indicates the remote is ready to use the Step and Set function.
2 Press the Cursor Up button to begin Step and Set. The selected mode button will turn off.
If no setup code is currently programmed for the selected mode, the search begins with the most popular setup code for the selected device. If a setup code has been previously programmed, the search begins with the next setup code for that device.
3 Use the following buttons to determine if the setup code properly operates the selected device:
Number buttons 0, 1, 2, or 3 (use to test TV setup codes)
Channel Up (use to test TV setup codes)
Play (use to test VCR setup codes)
Rewind (use to test VCR setup codes)
4 If the setup code successfully operates the device, press OK on the remote control. The setup code is now programmed into your remote control.
If the setup code does not operate the device, repeat steps 2 and 3.
During Step and Set, if there is more than a ten second pause between pressing buttons on the remote control, the remote will exit Step and Set and return to the previously programmed setup code.
You can only set up your remote control while in TV, VCR 1 or VCR 2 mode.
DCP501 User Guide
22
Overview
Installing Batteries in Remote Control
Before using the remote control, you must install two AA (1.5 V) alkaline batteries (included) To install batteries in the remote control: 1 Press and slide the battery compartment cover off, as illustrated in Figure 7:
Figure 7 Battery placement in remote control
1
2
+
+
2 Place the batteries in the compartment; be careful to observe the correct polarity. 3 Slide the battery compartment cover back into place.
NOTE!
Use and dispose of batteries in accordance with all applicable laws, rules and regulations. Motorola will not be liable to anyone for the user’s failure to use and/or dispose of batteries in the proper manner and in accordance with such laws, rules and regulations, or for any defect contained in batteries that may cause injury damage to persons or property.
DCP501 User Guide
TV and VCR Setup Codes
You can set up your remote control for your TV and VCR by consulting the tables below. Note that you only need to set up your remote control for your TV, VCR 1 and VCR 2 (if applicable).
For instructions on programming, verifying and finding setup codes for your remote control, see Remote Control in the “Overview” section.
TV Setup Codes
Manufacturer AOC Admiral Aiko Akai Alaron America Action Anam Audiovox Baysonic Belcor Bell & Howell Bradford Brockwood Broksonic CXC Candle Carnivale Carver Celebrity Cineral Citizen Concerto Contec Craig Crosley Crown
TV Setup Code 0019, 0030 0093, 0463 0092 0030 0179 0180 0180 0092, 0180, 0451, 0623 0180 0019 0016, 0154 0180 0019 0236, 0463 0180 0030, 0056 0030 0054 0000 0092, 0451 0030, 0056, 0060, 0092 0056 0180 0180 0054 0180
DCP501 User Guide
122
TV and VCR Setup Codes
Manufacturer Curtis Mathes
Daewoo Daytron Denon Dumont Electroband Emerson Envision Fisher Fujitsu Funai Futuretech GE Gibralter GoldStar Gradiente Grunpy Hallmark Harley Davidson Harman/Kardon Harvard Hitachi Infinity Inteq JBL JCB JVC KEC KTV Kenwood Konka LG LXI Logik Luxman MGA
TV Setup Code 0016, 0030, 0047, 0051, 0054, 0056, 0060, 0093, 0145, 0154, 0166, 0451, 0466, 0747, 1147, 1347 0019, 0092, 0451, 0623, 0624 0019 0145 0017, 0019 0000 0019, 0154, 0178, 0179, 0180, 0236, 0463, 0623, 0624 0030 0154 0179 0171, 0179, 0180 0180 0021, 0047, 0051, 0093, 0178, 0451, 0747, 1147, 1347 0017, 0019, 0030 0019, 0030, 0056, 0178 0053, 0056 0179, 0180 0178 0179 0054 0180 0016, 0056, 0145 0054 0017 0054 0000 0053 0180 0030, 0180 0019, 0030 0628, 0632, 0638, 0707 0056 0047, 0054, 0154, 0156, 0178, 0747 0016 0056 0019, 0030, 0150, 0178
DCP501 User Guide
Manufacturer MTC Magnavox Majestic Marantz Matsushita Megatron Memorex Midland Minutz Mitsubishi Motorola Multitech NAD NEC NTC Nikko Onwa Optimus Optonica Orion Panasonic Penney Philco Philips Pilot Pioneer Portland Prism Proscan Proton Pulsar Quasar RCA Radio Shack Realistic Runco
TV and VCR Setup Codes
123
TV Setup Code 0019, 0030, 0056, 0060 0030, 0054, 0179, 1254 0016 0030, 0054 0250 0145, 0178 0016, 0056, 0150, 0154, 0178, 0179, 0250, 0463 0017, 0047, 0051, 0747 0021 0019, 0093, 0150, 0178 0093 0180 0156, 0166, 0178 0019, 0030, 0056 0092 0030, 0092, 0178 0180 0154, 0166, 0250 0093 0179, 0236, 0463 0051, 0250 0019, 0021, 0030, 0047, 0051, 0056, 0060, 0156, 0178, 0747, 1347 0019, 0030, 0054, 0145, 0463 0054 0019, 0030 0166, 0679 0019, 0092 0051 0047, 0747 0178, 0466 0017, 0019 0051, 0250 0019, 0047, 0051, 0090, 0093, 0679, 0747, 1047, 1147, 1247, 1347, 1447 0019, 0030, 0047, 0056, 0154, 0178, 0180, 0747 0019, 0030, 0056, 0154, 0178, 0180 0017, 0030
DCP501 User Guide
124
TV and VCR Setup Codes
Manufacturer SSS Sampo Samsung Sansei Sansui Sanyo Scimitsu Scotch Scott Sears Semivox Semp Sharp Shogun Signature Sony Soundesign Squareview Starlite Supreme Sylvania Symphonic TMK TNCi Tandy Technics Technol Ace Techwood Teknika Telefunken Toshiba Vector Research Victor Vidikron Vidtech Wards
TV Setup Code 0019, 0180 0030 0019, 0030, 0056, 0060, 0178 0451 0463 0154 0019 0178 0019, 0178, 0179, 0180, 0236 0047, 0054, 0056, 0154, 0156, 0171, 0178, 0179, 0747 0180 0156 0093, 0688 0019 0016 0000 0178, 0179, 0180 0171 0180 0000 0030, 0054 0171 0056, 0178 0017 0093 0051, 0250 0179 0051, 0056 0016, 0019, 0054, 0056, 0060, 0092, 0150, 0179, 0180 0056 0060, 0154, 0156, 1256 0030 0053 0054 0019, 0178 0016, 0019, 0021, 0030, 0054, 0056, 0178, 0179
DCP501 User Guide
TV and VCR Setup Codes
125
Manufacturer White Westinghouse Yamaha Zenith
TV Setup Code 0463, 0623, 0624 0019, 0030 0016, 0017, 0092, 0463, 0624
VCR Setup Codes
Manufacturer Admiral Adventura Aiko Aiwa Akai America Action American High Asha Audiovox Beaumark Bell & Howell Broksonic CCE Calix Canon Carver Cineral Citizen Colt Craig Curtis Mathes Cybernex Daewoo Denon Dynatech Electrohome Electrophonic Emerex Emerson
VCR Setup Code 0048, 0209 0000 0278 0000, 0037 0041 0278 0035 0240 0037 0240 0104 0002, 0121, 0184, 0209, 0479 0072, 0278 0037 0035 0081 0278 0037, 0278 0072 0037, 0047, 0072, 0240, 0271 0035, 0041, 0060, 0162, 0760 0240 0045, 0278 0042 0000 0037 0037 0032 0000, 0002, 0037, 0043, 0121, 0184, 0209, 0278, 0479
DCP501 User Guide
126
TV and VCR Setup Codes
Manufacturer Fisher Fuji Funai GE Garrard Go Video GoldStar Gradiente HI-Q Harley Davidson Harman/Kardon Harwood Headquarter Hitachi Hughes Network Systems JVC Jensen KEC KLH Kenwood Kodak LXI Lloyd’s Logik MEI MGA MGN Technology MTC Magnasonic Magnavox Magnin Marantz Marta Matsushita Memorex
Minolta
VCR Setup Code 0047, 0104 0033, 0035 0000 0035, 0048, 0060, 0240, 0760 0000 0432, 0526 0037, 0038 0000 0047 0000 0038, 0081 0072 0046 0000, 0041, 0042 0042 0041, 0067 0041 0037, 0278 0072 0038, 0041, 0067 0035, 0037 0037 0000 0072 0035 0043, 0240 0240 0000, 0240 0278 0000, 0035, 0039, 0081, 0149 0240 0035, 0081 0037 0035, 0162, 0454 0000, 0035, 0037, 0039, 0046, 0047, 0048, 0104, 0162, 0209, 0240, 0454, 0479, 1037, 1162, 1262 0042
DCP501 User Guide
Manufacturer Mitsubishi Motorola Multitech NEC Nikko Noblex Olympus Optimus Orion Panasonic Penney Pentax Philco Philips Pilot Pioneer Polk Audio Profitronic Proscan Protec Pulsar Quarter Quartz Quasar RCA Radio Shack Radix Randex Realistic ReplayTV Runco STS Samsung Sanky Sansui Sanyo
TV and VCR Setup Codes
127
VCR Setup Code 0043, 0048, 0067 0035, 0048 0000, 0072 0038, 0041, 0067, 0104 0037 0240 0035 0037, 0048, 0104, 0162, 0432, 0454, 1048, 1062, 1162, 1262 0002, 0184, 0209, 0479 0035, 0162, 0225, 0454, 0616, 1062, 1162, 1262, 1362 0035, 0037, 0038, 0042, 0240 0042 0035, 0209, 0479 0035, 0081, 0618, 1081, 1181 0037 0067 0081 0240 0060, 0760 0072 0039 0046 0046 0035, 0162, 0454, 1162 0035, 0042, 0048, 0060, 0149, 0240, 0760 0000, 1037 0037 0037 0000, 0035, 0037, 0046, 0047, 0048, 0104 0614, 0616 0039 0042 0045, 0240 0039, 0048 0000, 0041, 0067, 0209, 0271, 0479 0046, 0047, 0104, 0240
DCP501 User Guide
128
TV and VCR Setup Codes
Manufacturer Scott Sears Semp Sharp Shintom Shogun Singer Sony Sylvania Symphonic TMK Tatung Teac Technics Teknika Thomas Tivo Toshiba Totevision Unitech Vector Vector Research Video Concepts Videosonic Wards White Westinghouse XR-1000 Yamaha Zenith
VCR Setup Code 0043, 0045, 0121, 0184 0000, 0035, 0037, 0042, 0046, 0047, 0104 0045 0048 0072 0240 0072 0000, 0032, 0033, 0035, 0636, 1032 0000, 0035, 0043, 0081 0000 0240 0041 0000, 0041 0035, 0162 0000, 0035, 0037 0000 0618, 0636 0043, 0045 0037, 0240 0240 0045 0038 0045 0240 0000, 0035, 0042, 0047, 0048, 0060, 0072, 0081, 0149, 0240, 0760 0072, 0209, 0278 0000, 0035, 0072 0038 0000, 0033, 0039, 0209, 0479
DCP501 User Guide
Documents / Resources
 |
MOTOROLA DCP501-R Universal Remote Control [pdf] User Guide DCP501-R, DCP501-R Universal Remote Control, DCP501-R, Universal Remote Control, Remote Control, Control |
