MOTOROLA SOLUTIONS VRX1000 Vehicle Two-Way Radio Enhancer
safer starts here
VRX1000
Ordering Guide
Important Notes
- Custom Filtering: Only the frequency plans shown in this ordering guide are available as standard configurations. For custom filtering, please contact a Sales Solution Specialist for assistance.
- Frequencies Required: VRX1000 frequencies must be specified when placing an order. If an in-band filter is ordered it is custom tuned and cannot be re-tuned in the field.
- Delivery Time: Standard VRX1000 delivery time is 22-24 weeks after receipt of a purchase order and a valid frequency plan. Frequency information must be accurate and in accordance with the frequency plan requirements described in this document in order to avoid delays.
- Control Heads: The APX'” Mobile radio can operate with up to two control heads while interfaced to a VRX1000.
- MSU Transmit Power: In all In-Band configurations, the MSU Transmit power must not exceed 50 Watts on DVRS Enabled MSU Modes due to the in-band filters’ power rating. The in-band filters connected to the MSU have typical insertion loss of 1.5dB
- Subscriber Options: APX'” Mobile Radios operating as the host mobile for the VRX1000 require subscriber option GA00631 for operation. APX™ Portable Radios operating through a VRX1000, utilizing the P25 Enhanced feature set require subscriber option QA00631.
Mobile Radio Type
Compatible Mobile Radios
Please refer to the Compatibility Charts under the Firmware section for complete information.
When Pairing with an APX™BS00 Mobile Radio
- Interface Kits: Depending on the isolation available between the APX™ BS00 mobile and VRX1000 antennas, an interface kit may be required. Download the Interface Kit Selection tool under the Ordering Guide header to determine which (if any) kit and installation drawing is required.
NOTE: For quoting purposes, the No Kit option may be selected but note that there is an additional cost if an interface kit is determined to be required later. - Required Y Cable: One of the following Y cables are required:
- Without SmartConnect- GA01515 (or KT000247 A01 as standalone accessory)
- splits the J2 into J2 and J600(DB25)
- With SmartConnect- GA01779 (or KT000247A04 as standalone accessory)
- allows RS232 and USB line to be used concurrently
How to Interpret a Frequency Plan Diagram
Below is an example of a frequency plan with the set of rules that must be met for it to be a valid selection. For this example, additional color coding was added for clarity.
7001800MHz Frequency Plan Example
- Ensure the VRX1 000 and System/Mobile frequencies are within the Valid frequency range (MHz)
- X/ VRX TX/Rx 769-773
- X/ MSU Rx Range 1 773-775
- X/ MSU Tx Range 2 806-824
- MSU Tx Range 1 799-805
- MSU Rx Range 2 851-869
- Ensure the Minimum separation (MHz) frequency requirements are met
- at least 3MHz between the highest VRX Tx/Rx frequency and lowest MSU Rx Range 1 frequency
- Ensure the Maximum bandpass (MHz) is not exceeded
- difference between the highest – lowest VRX Tx/Rx frequencies must be less than or equal to 1 MHz
Preparing a Quote Without Customer Frequencies
If preparing a quote before customer frequencies are known, please use the following:
Frequency Band (MHz) | Operation Mode | Frequency Plan | Lowest VRX1000
Transmit |
Highest VRX1000
Transmit |
System (Mobile Radio) Frequencies |
700/800 | In-Band | A1 |
770 |
771 |
Leave Blank |
Cross -Band | A | ||||
VHF | In-Band | A1 |
136 |
1 36.1 |
Leave Blank |
Cro ss-Band | A | ||||
UHF | In-Band | Al |
380 |
380.1 |
Leave Blank |
Cro ss-Band | A |
NOTE: This will allow the quoting process to continue but the order cannot be placed until the correct frequency plan and exact frequencies have been entered.
Selecting a Frequency Plan
Standard Frequency Plans
When the customer frequencies are known, follow the specified frequency requirements in the set of standard frequency plan diagrams to select the correct plan.
Custom Frequency Plans
When customer frequencies cannot meet all of the requirements of a standard frequency plan, this is a custom request. Please contact a Sales Solution Specialist to determine if a custom frequency plan is viable. If viable, a per unit custom charge is applicable.
Standard Frequency Plans
Frequency Band | Frequency Plan |
700/S00MHz | In-Band Plan Al |
In-Band Plan A2 | |
In-Band Plan Bl | |
In-Band Plan B2 | |
Cross-Band Plan A | |
VHF | In-Band Plan Al |
In-Band Plan A2 | |
In-Band Plan Bl | |
In-Band Plan B2 | |
Cross-Band Plan A | |
UHF | In-Band Plan Al |
In-Band Plan A2 | |
In-Band Plan 81 | |
In-Band Plan 82 | |
Cross-Band Plan A |
7001800MHz Frequency Plans
VHF 136-174MHz Frequency Plans
UHF Frequency Plans
Main Models: Dropship to New Part Numbers Mapping
The table below shows the mapping between the old dropship part numbers and the new model and option numbers. To compare a new quote to an older quote with dropship part numbers, each dropship number will map to the following:
- Main Model
- Tier 2 or Tier 3 (if applicable)
- In-Band Option (if applicable)
- Custom Frequency Plan (if applicable) TT06580AA->QA09537AA
APX Mobile Radio
Compatible Mobile Radio | Dropship # | Mobile Radio {CPQ) | Option# |
APX™ 250 0/ 4500/ 5500/ 6500 | TT05715AA | Single Band | QA09576AA |
APX™ 750 0 | TT05716AA | Dual Band {APX 7500) | QA09577AA |
APX™ 8500 | TT06279AA | All Band {APX 8500) | QA09578AA |
Main Model Description | Option Description | Dropship # | New Model/Option # |
VHF Cross-Band Analog (Tier 1) | TT2792A | M87KSS9AW1AN | |
P25 Operation & P25 Encryption (Tier 2) | TT05951AA | QA09634AA | |
P25 Enhanced Trunking Features (Tier 3) | TT05953AA | QA09635AA | |
VHF Frequency Plan A (In-Band Filter Kit) | TT05945AA | QA09289AA | |
VHF Frequency Plan B (In-Band Filter Kit) | TT05946AA | QA09289AA | |
UHF Cross-Band Analog (Tier 1) | TT2793A | M87PSS9PW1 AN | |
P25 Operation & P25 Encryption (Tier 2) | TT05951AA | QA09634AA | |
P25 Enhanced Trunking Features (Tier 3) | TT05953AA | QA09635AA | |
UHF Frequency Plan A (In-Band Filter Kit) | TT05947AA | QA09289AA | |
UHF Frequency Plan B (In-Band Filter Kit) | TT05948AA | QA09289AA | |
7001800MHz Cross-Band Analog (Tier 1) | TT2794A | M87USS9PW1AN | |
P25 Operation & P25 Encryption (Tier 2) | TT05951AA | QA09634AA | |
P25 Enhanced Trunking Features (Tier 3) | TT05953AA | QA09635AA | |
7001800MHz Frequency Plan A (In-Band Filter Kit) | TT05949AA | QA09590AA | |
7001800MHz Frequency Plan B (In-Band Filter Kit) |
TT05950AA |
QA09590AA |
Standalone Accessories
Functional Tiers and Feature Licenses
NOTES: All serial numbers must be provided at the time of order. Feature license(s) are not transferable between units.
If a feature license f1le{s) is lost, it must be re-purchased.
Name | Description | Option#
(Old Dropship#) |
Tier 2: P25 Digital Conventional Operation and Encryption | Enables the transparent pass through of P25 encryption between the P25 infrastructure, system subscriber units, the mobile radio, portable radios on the VRX1000 channel. | HKVN4974A
(DDN1960A) |
Required:
|
||
Tier 3: P25 Enhanced Trunking Operation | Allows the use of “DVRS Enabled” portable radios and provides the associated trunking features through the VRX1000. | HKVN4975A
(DDN1962A) |
P25 OTAR is supported via the VRX1000 on P25 Trunked FNE; P25 OTAR is NOT supported on P25 Conventional FNE. | ||
Prerequisite for:
|
||
Required:
|
||
Authentication | Portable Link Layer authentication through the VRX1000 prevents unauthorized portables accessing the radio network (per unit)
Required:
|
HKVN4976A
(DDN3116A) |
RM-OTAP | Enables the operator to perform firmware and configuration updates on each VRX1000 unit using Motorola Radio Management via the Mobile Ra dio.
Required:
|
HKVN4977A
(DDN3119A) |
PSU Conventional Scan (Bulk Order) | Enables an enhanced PSU to support conventional scan while the VRX1000 is configured as its system type.
Required:
Note: To qualify for bulk order, all serial numbers must be provided at the time of order. This license will only be applicable to the serial numbers provided. Should the customer fail to provide the serial numbers for all units at the time or order, the customer must place a new order when the remaining serial numbers are available. |
HKVN4978A
(DDN3174A) |
SmartConnect In-Vehicle Range Extension | Enables a “DVRS enabled” PSU to maintain voice and emergency services when SmartConnect MSU is connected via broadband (LTE, SAT, Wi-Fi) (per unit)
Required:
|
HKVN4979A
(DDN3229A) |
GPS Driven Deactivation | Enables a VRX1000 to be deactivated by a pre-configured GPS based (Speed & Distance) threshold to decide when to deactivate the primary VRX1000. (Per Unit)
Required:
|
HKVN4980A
(DDN3262A) |
Cables
Name | Description | Option#
(Old Dropship#) |
Programming Cable | Details: USB to mini USB, 1 Oft (PN AK672M_2-3-GR-R) | VKN0003A (DDN1968A) |
VRX to MSU Control Cable
SPARE |
Connects the VRX1000 to the MSU
Details: DB25 to DB25, 3ft (PN 7W087X07-01 is equivalent 1W087B01-01) |
|
VRX to MSU Y Control Cable (AUX)
SPARE |
Connects the VRX1000 to the MSU and provides access to the VRX1000 AUX pins (DB15)
Details: DB25 to DB25 & DB15 (PN 7W087X08-01 is equivalent to 1W087B05-01) |
|
RF Switch Cable
SPARE |
For use with Relay Kit (VLN0003A)
Details: 1 ft (PN 7W083X09-01) |
VKN0028A (DDN9032A) |
VRX to MSU Y Control Cable (Siren)
SPARE |
Connects the VRX1000 to the MSU and provides connection for Motorola Siren
Details: DB25 to DB25 & DB25, 3ft (PN 7W087X09-01) |
VKN0018A (DDN2053A) |
In-Band Notch Filter Cable
SPARE |
Connects the VRX1ODO to VRX1ODO In-Band filter
OR Connects non-APX™ 8500 Mobile Radio to Mobile Radio In-Band filter Details: Mini UHF (m) to mini UHF (m), 20″ (PN 7W087X11-01) |
VKN0002A (DDN1967A) |
In-Band Notch Filter Cable for APX8500
SPARE |
Connects APX™ 8500 Mobile Radio to Mobile Radio In-Band filter
Details: QMA RA (m) to mini UHF (m), 20″ (PN 7W900X94-01) |
VKN0024A (DDN2719A) |
DC Power Cable
SPARE |
Details: M12 Circular connector, 18ft (PN 7W087X20-01) | VKN0001 A (DDN1966A) |
Installation/Mounting Kits
Name | Description | Option#
(Old Dropship#) |
VRX1000 Mounting Kit
SPARE |
VBN0001A
(DDN1963A) |
|
VRX1000 In-Band Filter Mounting Bracket Kit | For use with stacked mount in-band filters | VBN0002A
(DDN1965A) |
VRX1000 Installation Kit
SPARE |
Includes Bracket, Mini UHF Connector, Fuse Kit, Power Cable | VBN0003A
IDDN2751A) |
Antennas
Name | Description | Option#
(Old Dropship#) |
VEHICLE ROOF/TRUNK MOUNT ANTENNAS- UNITY GAIN (OdBd) | ||
VHF Unity Gain Antenna | 136 – 144MHz | HAD4006A |
VHF Unity Gain Antenna | 144 – 150.8MHz | HAD4007A |
VHF Unity Gain Antenna | 1 50.8 – 162MHz | HAD4008A |
VHF Unity Gain Antenna | 162 -174MHz | HAD4009A |
UHF Unity Gain Antenna | 380 – 433MHz | HAE6012A |
UHF Unity Gain Antenna | 450 – 470MHz | HAE4003A |
UHF Unity Gain Antenna | 470- 512MHz | HAE4004A |
7001800MHz Unity Gain Antenna | 764 – 870MHz | HAF4016A |
MAG MOUNT ANTENNAS- UNITY GAIN (OdBd) | ||
VHF Unity Gain Mag Mount Antenna | For use with APX™ 8500 mobile radio
Freq Range : 136 – 174MHz |
VAD0001A
(DDN9014A) |
VHF Unity Gain Mag Mount Antenna | For use with non-APX™ 8500 mobile radios and VRX1000
Freq Range : 136 – 174MHz |
VAD0002A
(DDN9014A) |
UHF Unity Gain Mag Mount Antenna | For use with APX™ 8500 mobile radio
Freq Range : 380 – 520MHz |
VAE0001A
(DDN9015A) |
UHF Unity Gain Mag Mount Antenna | For use with non-APX™ 8500 mobile radios and VRX1000
Freq Range : 380 – 520MHz |
VAE0002A
(DDN9015A) |
7001800MHz Unity Gain Mag Mount Antenna | For use with APX™ 8500 mobile radio
Freq Range : 764 – 869MHz |
VAF0001A
(DDN9016A) |
7001800MHz Unity Gain Mag Mount Antenna | For use with non-APX™ 8500 mobile radios and VRX1000
Freq Range : 764 – 869MHz |
VAF0002A
(DDN9016A) |
In-Band Filter Kits
Name | Description | Option#
(Old Dropship#) |
Relay Kit | Filter Bypass kit provides access to full MSU frequency band when VRX1000 disabled.
Optional for use with all inband VRX1000 . |
VLN0003A(DDN2808A) |
VRX1000 IN-BAND FILTER KIT 71800MHz | For use with frequency plan in-band A1 | VFE0004A (DDN2077A) |
VRX1000 IN-BAND FILTER KIT 71800MHz | For use with frequency plan in-band A1 and APX™ 8500 | VFE0005A (DDN2077A) |
VRX1000 IN-BAND FILTER KIT 71800MHz | For use with frequency plan in-band A2 | VFF0007A(DDN2078A) |
VRX1000 IN-BAND FILTER KIT 71800MHz | For use with frequency plan in-band A2 and APX™ 8500 | VFF0008A(DDN2078A) |
VRX1000 IN-BAND FILTER KIT 71800MHz | For use with frequency plan in-band 81 | VFF0002A(DDN2078A) |
VRX1000 IN-BAND FILTER KIT 71800MHz | For use with frequency plan in-band 81and APX™ 8500 | VFF0005A(DDN2078A) |
VRX1000 IN-BAND FILTER KIT 71800MHz | For use with frequency plan in-band 82 | VFF0009A (DDN2077 A) |
VRX1000 IN-BAND FILTER KIT 71800MHz | For use with frequency plan in-band 82 and APX™ 8500 | VFF001QA (DDN2077A) |
VRX1000 IN-BAND FILTER KIT VHF | For use with any frequency plan | VFD0021A (DDN2073A/DDN2074A) |
VRX1000 IN-BAND FILTER KIT VHF | For use with any frequency plan and APX™ 8500 | VFD0022A (DDN2073A/DDN2074A) |
VRX1000 IN-BAND FILTER KIT UHF | For use with any frequency plan | VFE0016A (DDN2075A/DDN2076A) |
VRX1000 IN-BAND FILTER KIT UHF | For use with any frequency plan and APX™ 8500 | VFE0017A (DDN2073A/DDN2074A) |
VRX1000 IN-BAND FILTER KIT CUSTOM | For use with any custom frequency plan | VFN0016A |
VRX1000 IN-BAND FILTER KIT CUSTOM | For use with any custom frequency plan and APX™ 8500 | VFN0017A |
APX™SS00 Interface Kits
Use the Interface Kit Selection tool available here for download under Ordering Guide header to determine which (if any) kit and installation drawing are required.
Name | Description | Option#
(Old Dropship#) |
Single Triplexer Kit | H1919 | |
Single Triplexer w Relay Kit | For use with VHF Cross-Band | VFN0009A(DDN2658A) |
Single Triplexer w Relay Kit | For use with UHF Cross-Band | VFN001 QA (DDN2658A) |
Single Triplexer w Relay Kit | For use with 7001800MHz Cross-Band | VFN0011 A (DDN2658A) |
Dual Triplexer Kit | For use with Cross-Band | VFN0008A (DDN2657A) |
Dual Triplexer Kit | For use with In-Band | VFN0007A (DDN2657 A) |
Dual Triplexer w Relay Kit | For use with VHF Cross-Band | VFN0012A(DDN2659A) |
Dual Triplexer w Relay Kit | For use with UHF Cross-Band | VFN0013A (DDN2659A) |
Dual Triplexer w Relay Kit | For use with 7001800MHz Cross-Band | VFN0014A (DDN2659A) |
Relay Kit | For use with Cross-Band | VLN0004A(DDN2808A) |
Relay Kit | For use with In-Band | VLN0002A(DDN2808A) |
Training
Name | Description | Option#
(Old Dropship#) |
Basic Training (1 Day) | Includes soft copy of training materials. Customized training available subject to content and price negotiation.
Training the Trainer/End User Provides a general overview of Mobile Repeater solutions with respect to the agency’s particular use case. Best practices highlighted for common deployment scenarios. Participants will receive hands-on training for practical operation and control. Requirements: a minimum of 1 VRX1000 to be tested and in use on the system. OR Technical and Programming Training Provides radio technicians an in-depth understanding on how the VRX1000 is integrated into the everyday operation of the agency. Focuses on code plug compatibility, Futurecom Repeater Configurator (FRC) software functionality and programming for optimal end user experience. Requirements: a minimum of two fully functioning Portable radios (PSUs) programmed to the current system and at least one functional DVRS setup. DVRS setup includes a VRX1000 and a mobile radio (MSU) set. Requirement: Contact debra.oster@motorolasolutions.com or maria.tabladi llo@m otorolasolutions.com from the Worldwide Education organization to coordinate a training session. Please note that the lead time is ~180 days. |
PSV01S04247A
(DDN3699A) |
Extended Training | 1 additional day of on-site and/or virtual training
Requirements: Basic Training |
PSV01S04246A
(DDN3700A) |
Warranties & Services
NOTE: Warranties can be ordered as standalone up to 90 days after product purchase through after the fact purchase process.
Name | Description | Option# |
Essential Services | 3/5/7 year duration | LSV01S04106A |
Essential Services with Accidental Damage | 3/5/7 year duration | LSV01S04109A |
Installation Services | LSV01Q03645A | |
Programming Services | LSV01Q03648A | |
Professional Services | Deployment Optimization | LSV01 Q03650A |
Documents / Resources
![]() |
MOTOROLA SOLUTIONS VRX1000 Vehicle Two-Way Radio Enhancer [pdf] User Guide VRX1000 Vehicle Two-Way Radio Enhancer, VRX1000, Vehicle Two-Way Radio Enhancer, Two-Way Radio Enhancer, Way Radio Enhancer, Radio Enhancer |