MOTIONBLINDS CM-03-E User Guide

MOTIONBLINDS CM-03-E

WARNING
Read the instructions carefully before assembling and using the product. Assembly can be completed by non-professionals. For indoor use only.

• Young children can strangle themselves with the loop of pull cords, chains and tapes, and cords that operate window coverings.
• To avoid strangulation and entanglement, keep cords out of reach of young children.
• Cords may ensnare a child’s neck.
• Move beds, cots and furniture away from window covering cords.
• Do not tie cords together. Make sure cords do not twist together and form a loop.

Cleaning

Follow these general rules when cleaning the outside of the device and its components:

• Use a damp, soft, lint-free cloth. Avoid getting moisture in openings.
• Do not use aerosol sprays, solvents, alcohol, or abrasives.

Service & Support
Do not perform repairs yourself. Do not attempt to open the device or disassemble it. You run the risk of electric shock and voiding the limited warranty. No user-serviceable parts are inside.

Warranty Service
First follow the advice in this manual. If the product appears to be damaged or does not function properly, go to your local dealer for instructions on how to obtain warranty service.

Recycle
This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collec-tion systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.

Buttons and functions

1. Install the blind
   Follow the steps in the installation instructions to install the blind.
2. Activate the blind
   To activate the blind, connect it to a standard USB-C 5V power supply via a USB-C cable. This can be your smartphone’s power adapter, for example.
3. Add Eve MotionBlinds to your platform
   Add Eve MotionBlinds to the platform of your choice and make sure to have a compatible Thread Border Router.
   More information: motionblinds.com/eve/matter
4. Setup the blind
   Now you can easily add Eve MotionBlinds to your smart home in just a few steps by scanning the Matter Setup Code using the app of your favorite platform. Scan the Matter Setup Code to add it your platform.
   Eve MotionBlinds needs end positions to work properly. End positions can be programmed in two ways. In the Eve app or by the end position programming button on your blind. (Step 5)
   After scanning you can hide your Matter Setup Code.
5. Set end positions
   Beside setting the end positions by the app you are able to set the end positions by pressing the button on the motor. Pull and hold the chain until the blind has reached the bottom position. If the blind moves in the opposite direction, release the chain and pull and hold again.
   Adjust until the desired bottom position has been reached.
6. Save your bottom position
   When your blind is positioned at your bottom position hold the button until the blind moves up and down to save your bottom position.
7. Move your blind to the top position
   Pull and hold the chain until the blind has reached the top position. If the blind moves in the opposite direction, release the chain and pull and hold again.
   Adjust until the desired top position has been reached.
8. Save your top position
   When your blind is positioned at your top position hold the button until the blind moves up and down to save your top position.
9. Adjust your end positions
   To adjust one of your end positions you need to place your blind at the end position you want to adjust. Pull and wait until the blind has reached the end position you want to adjust.
10. Remove your (bottom/top) position
    Hold the end position program button for 3 seconds to remove your (bottom/top) position. The blind will step up and down once to confirm that your end position has been removed. You are now able to set a new (bottom/top) position.
11. Move your blind to the new (bottom, position
    Pull and hold the chain until the blind has reached the bottom position.If the blind moves in the opposite direction, release the chain and pull and hold again.
    Adjust until the desired bottom position has been reached.
12. Save your (bottom position
    When your blind is positioned at your bottom position hold the button until the blind moves up and down to save your bottom position.
13. Save the favorite position
    When there is no favorite position programmed, you need to position your blind at your favorite position. When the blind is at your favorite position hold the pull until the blind steps up and down once. Approximately 7 seconds)
14. Control your blind to favorite position
    When your blind is not positioned at the favorite position hold the pull for 5 seconds and your blind will move to it’s favorite position.
15. Save a new favorite position
    To remove your previous favorite position you need to place your blind at your current favorite position. (Step 10) Then Hold the pull until the blind steps up and down once. (Approximately 7 seconds) Your favorite position is now removed. Follow step 9 to set your new favorite position.

Change direction of rotation
If the position of the blind in the app is opposite to your blind, change the direction of rotation / pressing the End Position button twice within one second.

Recharge the blind

To charge the blind, connect it to a standard USB-C 5V power supply via a USB-C cable. This can be your smartphones power adapter, for example. Charge at least once a year.

More information
Please scan the QR code below to view the complete user manual with more information and advanced options.

Important Safety Instructions

WARNING: To reduce the risk of severe injury or death, it is important to follow these instructions for personal safety. Save these instructions.

• Read and follow all installation instructions.
• This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children should not play with the appliance. Cleaning and user maintenance should not be performed by children without supervision.
• Do not allow children to play with fixed controls. Keep remote controls away from children.
• Frequently examine the installation for imbalance and signs of wear or damage to cables and springs. Do not use if repair or adjustment is necessary.
• This instruction manual is also available on the website.
• The drive must be disconnected from its power source during cleaning, maintenance and when replacing parts.
• The A-weighted emission sound pressure level of the drive is equal to or less than 70dB(A).
• Indoor and household use only.
• Disconnect the drive from the power supply or switch off the automatic controls when maintenance, such as window cleaning, is being carried out in the vicinity.
• When operating a biased switch, make sure that other persons are kept away.
• Do not operate when maintenance, such as window cleaning, is being carried out in the vicinity.
• The tube motor must only be supplied with safety extra low voltage corresponding to the marking on the appliance.
• Maximum operating temperature of motor is +55°C.Maximum charging temperature of battery pack is +45°C.
• This appliance contains batteries that are non-replaceable.

Important Installation Instructions

WARNING: Important safety instructions. Follow all instructions, since incorrect installation can lead to severe injury.

• This motor can only be used with soft material for driven parts.
• Hazardous unprotected moving parts of the drive must be installed higher than 2.5m above the floor or any other level surface that could provide access to it.
• Install the actuating member of a manual release at a height less than 1.8m.
• The actuating member of a biased switch is to be located within direct sight of the driven part but away from moving parts. It is to be installed at a minimum height of 1.5m and not accessible to the public.
• The mass and the dimension of the driven part must be compatible with the rated torque and rated operating time.
• Fixed controls have to be clearly visible after installation.
• The driven part must be compatible with the rated torque 1.1 N.m and rated operating time (12 min).
• Minimum tube diameter: 025mm.
• The drive is intended to be installed at a height of at least 2.5m above the floor or any other accessible level surface.
• All-pole disconnection switches must be incorporated in the fixed wiring in accordance with the wiring rules.
• The appliance must only be supplied at safety extra low voltage corresponding to the marking on the appliance.
• Before installing the drive, remove any unnecessary cords or components and disable any equipment not needed for powered operation.

FCC Statement

FCC Manual | FCC ID: ZY4CM03E1
IC:28177-CM03E1|
Regulatory Information

FCC Information for User
This praduct does not contain any user serviceable components and is to be used with epproved antennas only. Any product changes or modifications will invalidate all applicable regulatory certifications and approvals.

FCC Electronic Emission Notices
This device complies with part 15 of the FCC Rules.

Operation is subject to the following conditions:

1. This device may not cause harmful interference
2. This device must accept any interference received, including interference that may cause undesired operation.

FCC Radio Frequency Interference statement

This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Operation of this equipment in a residential area
may cause harmful interference, in which case the user will be required to correct the interference at their own expense. li this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna
• Increase the distance separating the equipment and the receiver
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help

To satisfy FCC / IC RF exposure requirements, a separation distance of 20 cm or more should be maintained between the antenna of this device and persons during device operation. To ensure compliance, operations at closer than this distance is not recommended. EU Declaration Hereby, Coulisse declares that t00 00 equipment type CM-03-E is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: support.motionblinds.com

• Frequency range: 433 MHz, RF power: 2.32 dBm
• Frequency range BLE: 2402 – 2480 MHz.
• RF power: 3 dBm EIRP
• Frequency range Thread: 2405 – 2480 MHz.
• RF power: < 20 dBm EIRP

ISED Compliance
This device contains license-exempt transmitter(s)/receivers) that comply with Innovation, Science and Economic Development Canada s licence-exempt RSSis. Operation is subject to the following two conditions: This device may not cause interference. This device must accept any interference, including interference that may cause undesired operation of the device.

Reset the connection
Hold the program button for 10 seconds to delete the connection between the blind and the app. The LED lights up 5 times and the blind steps up and down 1 time to indicate that the connection is reset. Now the blind can be reconnected.

Reset the blind
Resetting the blind results in deleting the end positions and connections of the blind with apps and remote controls. Shortly press the program button to activate program mode. The blind will start stepping up and down.Hold the reset/ program button for at least 20 seconds to reset the blind. The blind will stop stepping twice. After the second stop, the blind will give one extra step to indicate that is has been reset.

FCC Manual | FCC ID: ZY4CM03E1
IC:28177-CM03E1

Regulatory Information

FCC Information for User serviceable components and is to be used with approved antennas only. Any product changes or moditications will invalidate all applicable regulatory certifications and approvals.

FCC Electronic Emission Notices
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions

1. This device may not cause harmful interference
2. This device must accept any interference received, including interference that may cause undesired operation.
3. FCC Radio Frequency Interference statement. This equipment hes been tested and found to comply with the limits for a class 8 digital device, pursuant to Part 15 of the FDC Rules.

These limits 16 are designed to provide reasonable protection against harmful interference when the equipment This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may Cause Operation of this equipment in a residential area may cause harmful interference, in which case the user will be required to correct the interterence at their own expense. If this equipment does cause a nearer interference to 1a01o wr reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna

• Increase the distance separating the equipment and the receiver
• Connect the equipment to an outlet on a circuit different from that to which the receiver is
• Consult the dealer or an experienced radio/TV engineer

To satisfy FCC / IC RF exposure requirements, a separation distance of 20 cm or more should be and persons during device operation. o ensure compliance, operations at closer than this distance is not recommended. EU Declaration Hereby. Coulisse declares that the radio equipment type is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: support.motiontinds.com

• Frequency range: 433 MHz, RF power: 2.32 dBm
• Frequency range BLE: 2402 – 2490 MHz,
• Rr power: 3 d8m EIRP
• Frequency range: 2405 – 2480 MHz,
• RF power: < 20 dBm EIRP

ISED Compliance
This device contains license-emattaners? receiver(s) that comply with Innovation, Science and Economic Development Canada s licence-exempt RSS|s). Operation is subject to the following two conditions: This device may not cause interference. This device must accept any interference, including interference that may cause unbested eat aut of the device.

Change motor speed / sound level
Hold the program button for 5 seconds to change the motor speed / sound level. The blind steps up and down 1 time to indicate that the speed has been adjusted to 1 of the 5 levels. Warning: release the button after 5 seconds when the blind steps up and down to avoid resetting the connection.

Hold the program button for 10 seconds to delete the connection between the blind and the app. The LED lights up 5 times and the blind steps up and down 1 time to indicate that the connection is reset. Now the blind can be reconnected.

Reset the blind
Resetting the blind results in deleting the end positions and connections of the blind with apps and remote controls. Shortly press the program button to activate program mode. The blind will start stepping up and down. Hold the reset/program button for at least 20 seconds to reset the blind. The blind will stop stepping twice. After the second stop, the blind will give one extra step to indicate that is has been reset.