Moory Nock Cover Insert Installation Guide

Moory Nock Cover Insert

Moory Nock Cover Insert

INSTALLATION GUIDE

Quick Setup / Use (Condensed)

  1. Before assembly: Always be two people during assembly and read the manual before starting.
  2. Safety: Use work gloves; be aware of pinch hazard during assembly.
  3. Follow the detailed installation steps: Assemble using the provided poles, connectors, legs, and cross braces for your selected length (6–12 m variants).
  4. Minimum clearance: Keep the stated minimum distance of 10–15 cm during the installation process (as referenced in the detailed installation section).
  5. Securing parts: Use the included 8 mm Allen key to tighten/adjust the brackets onto the rods as shown in the detailed installation illustrations.
Nock logo 

A-frame

Table of Contents

Overview installation Pages
NOCK Täckskär, 6 meter 2-3
NOCK Täckskär, 7 meter 4-5
NOCK Täckskär, 8 meter 6-7
NOCK Täckskär, 9 meter 8-9
NOCK Täckskär, 10 meter 10-11
NOCK Täckskär, 11 meter 12-13
NOCK Täckskär, 12 meter 14-15
Detailed installation manual 16-21

Information icon: a lowercase 'i' inside a circle.
Incorrect: One person carrying a heavy bundle of poles alone. Marked with an 'X'. Correct: Two people carrying the bundle of poles together. Marked with a checkmark.

Always be two people during assembly

Incorrect: A person attempting assembly without instructions, looking confused. Marked with an 'X'. Correct: A person sitting and reading the assembly manual. Marked with a checkmark.

Read the manual before assembly

Incorrect: A person looking at a pile of parts with a question mark, feeling confused. Marked with an 'X'. Correct: A person calling for support on a mobile phone. A speech bubble says 'moory'. Below is the phone number +46 8 251546. Marked with a checkmark.

Call us if you have any questions!

Warning icon: an exclamation mark inside a triangle.

Warning: pinch hazard

Incorrect: A bare hand being pinched between two metal tubes. Marked with an 'X'. Correct: A hand wearing a protective work glove holding the metal tubes safely. Marked with a checkmark.

Wear work gloves

NOCK6 meter

Image: Icon of an open box with a checklist, indicating the contents of the package.

Quantity Dimensions/Description Visual Representation
4 X (35 mm / 1.45 m) Image: Long silver pole for the boat cover frame.
4 X (25-30-35mm / 1.4-3.6 m) Image: Telescopic silver pole with black end caps for the boat cover frame.
4 X (30-35 mm / 0.9-1.8 m) Image: Telescopic silver pole with black end caps for the boat cover frame.
2 X (30 mm / 0.9 m) Image: Silver pole with a black end cap and a metal clamp for the boat cover frame.
2 X (25 mm / 0.9 m) Image: Silver pole with a black end cap and a metal clamp for the boat cover frame.
5 X (30 mm / 0.3 m) Image: Short silver pole with black end caps for the boat cover frame.
2 X (35 mm / 0.25 m) Image: Curved silver pole for the boat cover frame.
8 X (35 mm x 9 cm) Image: Small white connector component for the boat cover frame.
1 X (8 mm) Image: 8 mm Allen key for assembly.

Assembled Product

Image: Icon representing a tip or objective.

Image: Diagram of the assembled NOCK Täckskär boat cover frame, showing a large adjustable frame made of silver telescopic poles.

NOCK Täckskär, 6 meter

Icon of crossed wrench and screwdriver.

Installation overview

Overlaying tube

Label Quantity Component Name Visual
a 4 Överliggarrör / Overlaying tube Long straight tube
b 1 Koppling överliggarrör / Connector overlaying tube Short connector tube
c 1 T-koppling / T-connector Grey T-connector
d 1 Ändböj / End Elbow End elbow fitting
e 4 Däcksben / Deck leg Leg tube with fitting
f 4 Markben / Ground leg Leg tube with fitting
g 2 Tvärstag (hona) / Cross brace (female) Female cross brace
h 2 Tvärstag (hane) / Cross brace (male) Male cross brace

A long, straight silver metal tube, labeled 'a' at its right end.

Connector overlaying tube

A small, short silver metal tube connector, labeled 'b'.

T-connector

A small, grey plastic T-connector, labeled 'c'.

 End Elbow

A black plastic end elbow fitting, labeled 'd'.
A diagram showing the assembly of the NOCK Täckskär. It features a central horizontal tube (a) with several legs (f) attached. The legs are connected to the main tube using T-connectors (c) and connectors (b). The legs are further supported by cross braces (g and h). The entire structure is shown in a perspective view, with labels 'a', 'b', 'c', 'd', 'e', 'f', 'g', and 'h' pointing to the respective components.

Deck leg

A long, straight silver metal tube with a black plastic fitting at one end, labeled 'e'.

Ground leg

A long, straight silver metal tube with a black plastic fitting at one end, labeled 'f'.

Cross brace (female)

A long, straight silver metal tube with a black plastic fitting at one end, labeled 'g'.

 Cross brace (male)

A long, straight silver metal tube with a black plastic fitting at one end, labeled 'h'.

NOCK Täckskär, 7 meter

Icon of an open box with a checklist, representing the contents of the package.

Contents

Illustration of the Nock Täckskär carrying bag, which is dark green with the Nock logo and 'Täckskär' written on it.

1X

Illustration of the Nock Täckskär instruction manual, showing the Nock logo and the word 'Täckskär'.

1X

4 X (35 mm / 1.45 m)

Illustration of a long, silver, telescopic pole section.

1 X (35 mm / 1 m)

Illustration of a medium-length, silver, telescopic pole section.

4 X (25-30-35mm / 1.4-3.6 m)

Illustration of a long, silver, telescopic pole section with black end caps.

6 X (30-35 mm / 0.9-1.8 m)

Illustration of a long, silver, telescopic pole section with black end caps.

2 X (30 mm / 0.9 m)

Illustration of a long, silver, telescopic pole section with a black end cap and a hook.

2 X (25 mm / 0.9 m)

Illustration of a long, silver, telescopic pole section with a black end cap and a hook.

6 X (30 mm / 0.3 m)

Illustration of a short, silver, telescopic pole section.

2 X (35 mm / 0.25 m)

Illustration of a short, silver, telescopic pole section with a black end cap.

10 X (35 mm x 9 cm)

Illustration of a small, white, rectangular component, likely a connector or cap.

1 X (8 mm)

Illustration of a small, silver, L-shaped component, likely a connector or cap.
Icon of a target with an arrow, representing the intended use of the product.
Illustration of the Nock Täckskär netting system fully assembled, showing the telescopic poles and the netting structure.

 

NOCK Täckskär, 9 meter

Image: Icon of an open box with a checklist, indicating the contents of the package.

Innehåll / Contents / Sisältö / Indhold / Inhalt / Inhoud / Contenu / Contenido / Conteúdo / Contenuto / Obsah / Zawartość

Image: A long, dark grey carrying bag with two shoulder straps and the NOCK logo.

1X

 Image: A white instruction manual with the NOCK logo and the word ‘Täckskär’.

1X
6 X (35 mm / 1.45 m)

Image: A long, silver, telescopic pole section.
1 X (35 mm / 0.5 m)

Image: A short, silver, telescopic pole section.
4 X (25-30-35mm / 1.4-3.6 m)

Image: A long, silver, telescopic pole section with black end caps.
6 X (30-35mm / 0.9-1.8 m)

Image: A long, silver, telescopic pole section with black end caps.
2 X (30 mm / 0.9 m)

Image: A long, silver, telescopic pole section with a black end cap and a metal ring.
2 X (25 mm / 0.9 m)

Image: A long, silver, telescopic pole section with a black end cap and a metal ring.
8 X (30 mm / 0.3 m)

Image: A short, silver, telescopic pole section.
2 X (35 mm / 0.25 m)

Image: A short, silver, telescopic pole section with a black end cap.

 10 X (35 mm x 9 cm)

Image: A small, white, rectangular component, likely a connector or cap.

 1X (8 mm)

Image: A small, silver, L-shaped component, likely a connector or cap.

Image: Icon of a target with an arrow, indicating the intended use of the product.

Image: A diagram showing the assembled NOCK Täckskär, a long, silver, telescopic pole structure with multiple legs and a central horizontal bar.

NOCK Täckskär, 9 meter

Icon of crossed wrench and screwdriver.

Översikt installation / Installation overview / Asennuksen yleiskatsaus / Installationsoversigt / Installationsübersicht / Aperçu de l’installation / Resumen de la instalación / Visão geral da instalação / Panoramica dell’installazione / Přehled instalace / Przegląd instalacji

Quantity Description (Swedish / English) Reference Label
6 X Överliggarrör lång / Overlaying tube long a
1 X Överliggarrör kort / Overlaying tube short b
— Koppling överliggarrör / Connector overlying tube c
— T-koppling / T-connector d
— Ändböj / End Elbow e
6 X Däcksben / Deck leg f
4 X Markben / Ground leg g
2 X Tvärstag (hona) / Cross brace (female) h
2 X Tvärstag (hane) / Cross brace (male) i

Overlaying tube long

Long overlaying tube (a)

Overlaying tube short

Short overlaying tube (b)

Connector overlaying tube

Connector overlaying tube (c)

T-connector

T-connector (d)

End Elbow

End Elbow (e)
Diagram showing the assembly of the NOCK Täcksär structure. The diagram illustrates the connection of various components: long overlaying tubes (a), short overlaying tubes (b), connectors (c), T-connectors (d), end elbows (e), deck legs (f), ground legs (g), cross braces (h and i). The structure is shown in a perspective view, highlighting the arrangement of the legs and the cross-bracing system.

Deck leg

Deck leg (f)

Ground leg

Ground leg (g)

Cross brace (female)

Cross brace (female) (h)

/ Cross brace (male)

Cross brace (male) (i)

NOCK Täckskär, 10 meter

Image: Icon of an open box with a checklist inside, representing the contents of the package.

Innehåll / Contents / Sisältö / Indhold / Inhalt / Inhoud / Contenu / Contenido / Conteúdo / Contenuto / Obsah / Zawartość

Image: Illustration of the Nock Täckskär carrying bag, which is dark grey with a green Nock logo and a carrying strap.

1X

 Image: Illustration of the Nock Täckskär instruction manual, showing the product name and logo.

1X
6 X (35 mm / 1.45 m)

Image: Illustration of a long, straight silver pole section.
1 X (35 mm / 1.30 m)

Image: Illustration of a long, straight silver pole section.
4 X (25-30-35mm / 1.4-3.6 m)

Image: Illustration of a long, straight silver pole section with black end caps.
6 X (35 mm / 1.3-2.5 m)

Image: Illustration of a long, straight silver pole section with black end caps.
2 X (30-35 mm / 0.9-1.8 m)

Image: Illustration of a long, straight silver pole section with black end caps.
2 X (30 mm / 1 m)

Image: Illustration of a long, straight silver pole section with a black end cap and a metal ring.
2 X (25 mm / 1 m)

Image: Illustration of a long, straight silver pole section with a black end cap and a metal ring.
8 X (30 mm / 0.3 m)

Image: Illustration of a short, straight silver pole section.

 12 X (35 mm x 9 cm)

Image: Illustration of a small, rectangular metal component.

 1 X (8 mm)

Image: Illustration of a small, L-shaped metal component.

 2 X (35 mm / 0.25 m)

Image: Illustration of a curved silver pole section.

Image: Icon of a target with an arrow in the bullseye, representing the final assembly.

Image: Illustration of the fully assembled Nock Täckskär, showing the long silver pole supported by multiple legs and cross-braces.

Ref Quantity Swedish Name English Name Image
a 6 X Överliggarrör lång Overlaying tube long Image: Long overlaying tube (a)
b 1 X Överliggarrör kort Overlaying tube short Image: Short overlaying tube (b)
c Koppling överliggarrör Connector overlying tube Image: Connector overlying tube (c)
d T-koppling T-connector Image: T-connector (d)
e Ändböj End Elbow Image: End Elbow (e)

Main assembly diagram showing the structure of the NOCK Täckskär with various components labeled a through j.

Ref Quantity Swedish Name English Name Image
f 6 X Däcksben lång Deck leg long Image: Long deck leg (f)
g 2 X Däcksben kort Deck leg short Image: Short deck leg (g)
h 4 X Markben Ground leg Image: Ground leg (h)
i 2 X Tvärstag (hona) Cross brace (female) Image: Cross brace (female) (i)
j 2 X Tvärstag (hane) Cross brace (male) Image: Cross brace (male) (j)

NOCK Täckskär, 11 meter

Icon of an open box with a checklist, indicating the contents of the package.

Innehåll / Contents / Sisältö / Indhold / Inhalt / Inhoud / Contenu / Contenido / Conteúdo / Contenuto / Obsah / Zawartość

Icon of a target with an arrow, indicating the intended use of the product.
Illustration of the NOCK Täckskär tent structure, showing the poles and the black fabric cover.

NOCK Täckskär, 11 meter

Image: Icon of crossed wrench and screwdriver.

Installation overview

Quantity Part Name (SE / EN) Label Image
7 X Överliggarrör lång / Overlaying tube long a Image: Long overlaying tube labeled (a).
1 X Överliggarrör kort / Overlaying tube short b Image: Short overlaying tube labeled (b).
Koppling överliggarrör/ Connector overlaying tube c Image: Connector for overlaying tube labeled (c).
T-koppling / T-connector d Image: T-connector labeled (d).
Ändböj / End Elbow e Image: End elbow labeled (e).

Image: Main assembly diagram showing the structure of the NOCK Täckskär.

Quantity Part Name (SE / EN) Label Image
8 X Däcksben lång / Deck leg long f Image: Long deck leg labeled (f).
2 X Däcksben kort / Deck leg short g Image: Short deck leg labeled (g).
4 X Markben / Ground leg h Image: Ground leg labeled (h).
2 X Tvärstag (hona) / Cross brace (female) i Image: Cross brace (female) labeled (i).
2 X Tvärstag (hane) / Cross brace (male) j Image: Cross brace (male) labeled (j).

NOCK Täckskär, 12 meter

Image: Icon of an open box with a checklist inside, representing the contents list.

Contents

Quantity Dimensions / Description Image
1X Carrying bag Image: A long, dark grey carrying bag with two handles and the NOCK logo.
1X Instruction manual Image: A white instruction manual with the NOCK logo and the word ‘Täckskär’.
8 X (35 mm / 1.45 m) Image: A long, silver telescopic pole section.
1 X (35 mm / 0.5 m) Image: A shorter, silver telescopic pole section.
4 X (25-30-35mm / 1.4-3.6 m) Image: A long, silver telescopic pole section with black end caps and two adjustment locks.
6 X (30-35 mm / 1.3-2.5 m) Image: A long, silver telescopic pole section with black end caps and one adjustment lock.
4 X (30-35 mm / 0.9-1.8 m) Image: A long, silver telescopic pole section with black end caps and one adjustment lock.
2 X (30 mm / 1 m) Image: A long, silver telescopic pole section with a black end cap and a hook/clamp.
2 X (25 mm / 1 m) Image: A long, silver telescopic pole section with a black end cap and a hook/clamp.
10 X (30 mm / 0.3 m) Image: A short, silver telescopic pole section.
14 X (35 mm x 9 cm) Image: A plastic bracket or clip.
1 X (8 mm) Image: An Allen key.
2 X (35 mm / 0.25 m) Image: A curved, silver telescopic pole section.

Icon of a target with an arrow in the bullseye, representing the final assembly. A large, silver telescopic pole structure, likely a cover or shelter, shown in its assembled state.

NOCK Täckskär, 12 meter

Icon of crossed wrench and screwdriver.

Översikt installation / Installation overview / Asennuksen yleiskatsaus / Installationsoversigt / Installationsübersicht / Aperçu de l’installation / Resumen de la instalación / Visão geral da instalação / Panoramica dell’installazione / Přehled instalace / Przegląd instalacji

Quantity Description (Swedish/English) Reference label
8 X Överliggarrör lång / Overlaying tube long a
1 X Överliggarrör kort / Overlaying tube short b
Koppling överliggarrör / Connector overlying tube c
T-koppling / T-connector d
Ändbøj / End Elbow e
8 X Däcksben lång / Deck leg long f
2 X Däcksben kort / Deck leg short g
4 X Markben / Ground leg h
2 X Tvärstag (hona) / Cross brace (female) i
2 X Tvärstag (hane) / Cross brace (male) j

Overlaying tube long

Long overlaying tube (a)

Overlaying tube short

Short overlaying tube (b)

Connector overlaying tube

Connector overlaying tube (c)

T-connector

T-connector (d)

End Elbow

End Elbow (e)
Diagram of the NOCK Täckskär structure showing the assembly of the main frame with various components labeled a through j.

Deck leg long

Long deck leg (f)

Deck leg short

Short deck leg (g)

Ground leg

Ground leg (h)

Cross brace (female)

Cross brace (female) (i)

Cross brace (male)

Cross brace (male) (j)

Detailed installation /

 


Minimum 10-15 cm


1

Diagram showing two separate metal rod segments being brought together to be joined. An arrow indicates the left segment is being inserted into the right segment's connector.

a.

Diagram a: Close-up of a connector on a rod. A dashed oval with an arrow indicates loosening the cap by rotating it counter-clockwise.

b.

Diagram b: Close-up showing the cap being removed from the threaded end of the connector, indicated by a downward arrow.

c.

Diagram c: Close-up showing a metal rod being inserted into the connector. Two downward arrows indicate the direction of insertion.

d.

Diagram d: Close-up showing the cap being tightened onto the connector. A dashed oval with an arrow indicates clockwise rotation.

2

Diagram showing three stages of adjusting a telescopic rod. Stage 'a' shows loosening the connector with a counter-clockwise rotation. Stage 'b' shows adjusting the rod's length, indicated by a double-headed arrow for extension or retraction. Stage 'c' shows tightening the connector with a clockwise rotation.

3

Diagram of a triangular frame assembly consisting of a horizontal base pole and two angled poles meeting at a peak. Arrows indicate connection points at the ends of the horizontal pole. Step a: Hand holding a connector piece near the end of a pole. Step b: Hand attaching a C-clip to a pole. Step c: Hand inserting a screw or pin into the C-clip on the pole. Step d: Hand sliding a connector onto a pole. Step e: Final connection of the horizontal pole to the angled pole.

4

Step a: A straight pole being inserted into a curved handle, indicated by a horizontal arrow showing linear movement. Step b: A dashed circular arrow around the straight pole indicating rotation. Step c: Telescoping action where an inner pole is pulled out from the straight pole, indicated by a dashed horizontal arrow showing linear movement. Step d: A dashed circular arrow around the extended pole indicating rotation.

i

A perspective view of a grey, L-shaped metal bracket with two circular holes on its top surface.
An exploded view diagram showing the bracket being assembled onto a vertical metal rod. A bolt is shown passing through the bracket and the rod. Dashed lines and arrows indicate the alignment and direction of assembly.

5

A top-down assembly diagram of a tripod. Three legs, each composed of two telescopic sections, are shown converging at a central point. Above the legs, a horizontal bar with a curved end is shown. Two small grey brackets are positioned on either side of the central convergence point, with an upward arrow indicating they will be attached to the legs.

  • a. Image: Illustration ‘a’ showing a hand using a hex key (Allen wrench) to tighten a screw on a bracket that is already partially attached to a metal rod.
  • b. Image: Illustration ‘b’ showing a hand using a hex key (Allen wrench) to adjust the bracket on the rod, ensuring it is properly seated.
  • c. Image: Illustration ‘c’ showing a hand inserting a rod into the bracket. An arrow indicates the upward direction of insertion.
  • d. Image: Illustration ‘d’ showing a hand using a hex key (Allen wrench) to fully secure the bracket onto the rod.

6

Diagram 6: A line drawing of a boat with a support frame installed. The frame consists of two vertical poles connected by a horizontal crossbar, forming an A-frame shape over the boat's deck.
Component Diagram: Arrows indicate where these parts are added in step 7.

7

Diagram 7: A line drawing of the boat from diagram 6, now showing an additional support pole extending from the center of the horizontal crossbar down to the boat's deck, creating a tripod-like support structure.

8

Diagram 8: Boat frame assembly with labels a, b, and c.

9

Diagram 9: Boat covered with a protective net.

Troubleshooting

  • Assembly difficulty / unsure about steps: Call the provided support line if you have any questions.
  • Safety concerns during fitting: Stop and re-check that you are using work gloves and that you are assembling correctly to avoid pinch hazards.
  • Parts not seating properly: Re-check that brackets are adjusted so they are properly seated on the rods, then tighten fully with the 8 mm Allen key.

FAQ

How many people should assemble the NOCK Täckskär?

Always be two people during assembly.

Do I need to read the manual before assembly?

Yes—read the manual before assembly.

Use work gloves, and be aware of pinch hazard (clämrisk/risk de pincement/Quetschgefahr).

What if I have questions during installation?

Call support if you have any questions.

 

Documents / Resources

PDF thumbnailNock Cover Insert
Installation Guide · 6 meter, 7 meter, 8 meter, 9 meter, 10 meter, 11 meter, Nock Cover Insert, Cover Insert, Nock Cover

References

Published: July 21, 2026

Ask a Question

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

Ask a Question

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.

Moory BC118 Battery Charger User Manual
January 18, 2026
Moory 250 mm Storm Lantern Kerosene Lantern Installation Guide
October 24, 2025
Moory 1102150 Series Tubular Heater Instruction Manual
February 20, 2025
Moory TH Series Tubular Heater Instruction Manual
July 18, 2024