MOONS NPSUGMDHB Wireless Node Controller Owner’s Manual

MOONS NPSUGMDHB Wireless Node Controller

Specifications

• Customer’s Part Number:
• MOONS’ Part Number: 4696355000211
• Model: NPSUGMDHB
• P/N: A8768

Subject to change without notice

DESCRIPTIONS

• The Wireless Node Controllers can be installed in the lighting control box, lamp chamber or installed self-contained under eaves or other sheltered areas due to the solid metal enclosure.
• It is very small size and excellent waterproof.
• It can automatically identify different types of LED driver, such as 0-10V, DALI-2/D4i and DMX(RDM).
• Supports 2 channels 0-10V for color temperature adjustment.
• Supports RGBW color.
• Supports dynamic scenes and animations.
• It communicates with the gateway through a WPAN (Sub-GHz).
• Self-building and self-healing MESH Network.
• The sensor interface supports sensor access with digital and analog outputs.

FEATURES

• Input voltage:12-30VDC.
• Power consumption: < 1W.
• Wireless communication: IEEE 802.15.4-915MHz.
• Automatically identify dimming mode.
• DMX(RDM) master, up to 6 loads.
• DALI-2/D4i Single-Master Controller, up to 6 loads.
• 2 channels of 0-10V Dimmer, up to 4 loads each channel.
• RGBW color support
• Dynamic scenes and animations
• 1 channel of sensor sample input.
• Save several dimming plans.
• Firmware upgrade: OTA.
• Embedded communication encryption mechanism.
• Radio frequency certification: FCC
• Warranty: 5years.

CHARACTERISTICS

 ELECTRICAL CHARACTERISTICS
At 20 ℃, 50% RH, 100Kpa conditions.

Note:

1. In the case of DALI-2/D4i mode, the input voltage needs to be higher than the DALI BUS voltage.
2. When the input voltage is 12V, 0-10V can output 10V at most; When the output voltage is > 12V, 0-10V can output 11V.

Operating Conditions

EMC

Certification

Mechanical Data

Dimensions
Dimensions are provided in the diagrams above.

Antenna

 Optional accessories

LABEL 

Product barcode information:

• The last 8 digits of SN represent the communication address of the product.
• A” indicates that this product operates in the American frequency band;
• The QR code shows the product’s communication address.

Function Descriptions

Interfaces

WPAN Module

• Communicate with the Gateway. Transfer various instructions, such as: dimming command, upload power metering data, set parameters and query telemetries accordingly and so on.
• Wireless communication: IEEE 802.15.4-Sub-GHz.
• Embedded communication encryption mechanism.

Dimming
Once the device is powered up, it will automatically identify the dimming mode (DALI-2/D4i / DMX(RDM) /0-10V) of the connected load. After recognition, it will automatically report its own running dimming mode and perform necessary operation in this way.

Notice: To achieve perfect recognition of the dimming type, it is recommended that the controller and the LED driver be powered on simultaneously, or the controller be powered on later than the LED driver.

0-10V Dimming

• If it is identified as 0-10V dimmer, it can support 2-channel independent 0-10V dimming, which can support adjusting the color temperature (tunable white LED driver and software configuration are required).
• The DIM-TO-OFF LED drivers should be used; the LED drivers’ output will turn off once the dimming voltage is < 0.5V.
• Support positive and negative logic dimming (configuration required).
• If each channel is connected to multiple LED drivers, the maximum output current of each channel is 10mA, and if the load current is >10mA, the output voltage will be not accurate.

Notice: When the input voltage is 12V, 0-10V can output 10V at most; When the output voltage is > 12V, 0-10V can output 11V.

DMX(RDM)

• If identified as a DMX(RDM) master, it can support up to 6 loads (maximum 3 slots for each load) and can be automatically addressed to support RDM instructions.
• 4 loads are recommended.

DALI-2/D4i

• If identified as a DALI-2/D4i Single-Master Controller, up to 6 loads (one address for each load) can be supported, supporting IEC62386-101/103/251/252/253/351 (TYPE D).
• 4 loads are recommended.

Notice:

• At least one of the DALI-2/D4i LED drivers needs to be set to supply power to the DALI bus.
• Maximum of 6 DALI-2/D4i LED Drivers, any DALI-2/D4i LED Drivers >4 will need the power supply disabled
• In the case of DALI-2/D4i mode, the input voltage needs to be higher than the DALI BUS voltage.

Sensor Input

• 1 channel of sensor input interface.
• Sensors with 0-10V output can be accessed.
• Passive digital output can be accessed.
• Sensors must be configured in software before it is functional in system.

Indicator Lights

Notice: 

1.  Purple light indicates that the communication between node controller and LED driver is lost. This might be due to use wrong LED driver or LED driver is not power on or wiring error (for example the reverse connection of the DMX bus). Please check the wiring connection or the power-on status of the LED driver, and then re-power the node controller.

INSTALLATION

For DALI-2/D4i applications with sensor

For DMX(RDM) applications with sensor 

For 0-10V Dim to off applications with sensor 

 For 0-10V Tunable white applications with sensor 

 Recommended installation of antenna interface 

 Recommended installation of M18 Antenna 

ORDERING

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna.

CUSTOMER’S APPROVAL STAMP
Please sign back after your approval. The specifications will come into force when we receive purchase order.

Subject to change without notice
© 2024 MOONS’. All rights reserved. All content contained herein is subject to change without prior notice. More product documentation and MOONS’ terms and conditions are available at https://www.moonsindustries.com

History Version