MONSTER YS03 Multi Function Bluetooth Speaker
Product Parameters
- Product Name
- Monster Soundbase YS03
- Bluetooth version
- V5.4
- Wireless range
- >10m
- Specification
- 40 low (Ipcs)
- Frequency Response
- 45HZ-20KHZ
- Input
- 5V=1A
- SNR
- >80dB
Packing List
Product Instruction Diagram
- Power On/Off
- Next Track / Volume Up
- Play/Pause/Answer/End Call
- Previous Track / Volume Down
- Microphone
- Battery Indicator Light
- Bluetooth Indicator Light
- AUX Port
- TF card Slot
- Type-C Port
- USB Port
Speaker Function
Speaker Function Button Explanation Translation in Chinese
Answer / Hang up / Reject a call
- When connected to your phone via Bluetooth:
- Short press ”
“Answer/End call - Long-press” ” Reject call
AUX In / Sound Card Input Operation Guide
Connect a 3.5mm AUX audio cable to your computer’s audio port, power on the speaker, and short-press the power button to switch to sound card mode (blue indicator steady on). Note: 3.5mm audio cable is not included as standard.
- Insert TF card for card reader mode.
- Insert the USB drive for USB mode.
- In Sound Card Mode, the speaker does not support volume synchronization. To adjust volume, adjust thevolume volume levels on both the speaker and the computer separately.
Precautions
Read and follow all instructions
- Do not expose the product to dripping or splashing water, or place liquid-filled items (e.g. vases) on it.
- Do not place unshielded heat sources (e.g., lit candles) on the product.
- Keep the product away from direct sunlight, open flames, or other heat sources.
- exposure to rain, water immersion, or use in extremely cold, hot, or humid environments.Avoid.
- Use moderate volume to prevent hearing damage.
- Use aUSB cable to connect the speaker to the power supply in all audio modes for normal operation.
- Disconnect all power when the product is not in use for a long time.
- Hazardous voltage inside the speaker. Do not disassemble it to avoid electric shock and warranty invalidation.
FCC
FCC Statement
This Equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide Reasonable Protection against Harmful Interference in a residential Installation. This Equipment generates uses and can radiate radio Frequency Energy and, if not installed and used in Accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference
- This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance COUId void the user’s authority to operate the equipment.
FCCID: 2A8PV-YS03
Environment-Friendly Use Period (EFUP)
This logo refers to the period (10 years) during which the hazardous substances in electronic and electrical produsts will not leak or mutate so that the use Of these [substances] will not result in any severe environmental pollution, any bodily injury or damage to any assets.
Warranty Service
Dear user, this warranty card is the proof of your future warranty application, please cooperate with the seller to fill it out and keep it for future use!
Documents / Resources
 | YS03 Multi Function Bluetooth Speaker |
References
- User Manualmanual.tools