MonstaTek M1 Compact Multitool User Manual

MonstaTek M1 Compact Multitool

Specifications

• Dimensions: 250 mm x 50 mm x 212 mm x 106 mm (Note: Dimensions provided seem to be a list of individual measurements rather than a single set of dimensions. Please clarify if these are for different parts or a single product.)
• Model: M1
• Storage: Supports microSD cards up to 256 GB (recommended 16 GB minimum for best performance). Compatible with exFAT and FAT32 file systems.
• Power System:
  • Battery Capacity: 2100 mAh
  • Battery Life: 20 days
  • Charge Time: 2 hours
  • Power Connector: USB Type-C
  • Charging Voltage and Current: 5 V, 1 A
  • Battery Operating Voltage: 3.3-4.2 V
  • Pin 1 Voltage (power supplied directly from USB): 5 V
  • Maximum USB Cable Power Supply Current (including connected devices): 3 A

Getting Started

1. Plug in the M1 using a USB-C cable connected to a 5V/1A power supply.
2. Press and hold the Main button for about 3 seconds until the device powers on.

Adding Storage

1. Insert a microSD card into the slot as shown in the diagram.
2. The M1 supports cards up to 256 GB. For best performance, we recommend using at least 16 GB.
3. The device is compatible with exFAT and FAT32 file systems.
4. If your card is not already formatted, you can format it directly from the M1 menu.

Rebooting the Device

1. Connect your M1 to a computer using a USB cable.
2. Open a web browser and go to update.monstatek.com.
3. Follow the on-screen instructions to install the latest firmware.

Keeping your M1 updated ensures you always have the newest features, improvements, and bug fixes.

Power system characteristics

1. Battery capacity: 2100 mAh
2. Battery life: 20 days
3. Charge time: 2 hours
4. Power connector: USB Type-C
5. Charging voltage and current: 5 V, 1 A
6. Battery operating voltage: 3.3-4.2 V
7. Pin 1 voltage (power is supplied directly from USB): 5 V
8. Maximum USB cable power supply current, including connected devices: 3 A

FCC

FCC Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. RF warning statement: The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction

IC Compliance

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause undesired operation of the device

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. RF warning statement: The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

MORE INFORMATION

Join Us

• monstatek.com
• facebook.com/Monstatek
• instagram.com/monstatek
• x.com/Monstatek

FAQs

• Q: What is the maximum storage capacity supported by the M1?
  • A: The M1 supports microSD cards up to 256 GB.
• Q: What file systems are compatible with the M1?
  • A: The device is compatible with exFAT and FAT32 file systems.
• Q: How do I format my microSD card if it’s not already formatted?
  • A: You can format it directly from the M1 menu.
• Q: How long does the battery last on a full charge?
  • A: The battery life is approximately 20 days.
• Q: How long does it take to fully charge the M1?
  • A: The charge time is 2 hours.
• Q: Is it safe to randomly eject the SD card?
  • A: WARNING: DO NOT RANDOMLY EJECT THE SD CARD.