MODE AUDIO NTA3.2DSP Network Dsp Power Amplifier
IMPORTANT SAFETY INSTRUCTIONS
- Read all safety and operating instructions before using this product.
- All safety and operating instructions should be kept for future reference.
- Read and understand all warnings listed on the operating instructions.
- Follow all operating instructions to operate this product.
- This product should not be used near water, ie. Bathtub, sink, swimming pool, web basement etc.
- Only use dry cloth to clean this product.
- Do not block any ventilation openings, it should not be placed flat against a wall or placed in a built-in enclosure that will impede the flow of cooling air.
- Do not install this product near any heat sources, such as, radiators, heat registers, stove or other apparatus (including heat producing amplifiers) that produce heat.
- Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The side blade or the third prong are provided for your safety if the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
- Protect the power cord being walked on or pinched particularly at Plugs, convenience receptacles and the point where they exit from the apparatus. Do not break the ground pin of the power supply cord.
- Only use attachments specified by the manufacturer.
- Use only the cart, stand, tripod, bracket, or table specified by the manufacturer or sold with the apparatus. When a cart is used use caution when moving cart/apparatus combination to avoid injury from tip-over.
- Unplug this apparatus during lightning storms or when unused for long periods of time.
- Care should be taken so that objects do not fall and liquids are not spilled into the unit through the ventilation ports or any other openings.
- Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way; such as, power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally or ha been dropped.
- WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
- When the MAINS plug, or an appliance coupler is used as the disconnect device, the disconnect device should remain readily operable.
- Protective Ground Terminal: The apparatus shall be connected to an AC main socket with a protective earth ground connection.
INTRODUCTION
NPA3.2DSP is a 2inZout network DSP power amplifier, integrated with DSP processor, IPS colorful display and other powerful functions. This amplifier supports analog inputs or Dante network. Support constant resistance 82\40 and constant voltage 100V 70V. The amplifier comes with the standard FIR automatic linear magnitude and phase function, user can easily preset the speaker parameters to achieve the ideal system setting. Real time power, current, voltage, temperature and impedance can be monitored and shown in the LCD display. With RJ45IUSB and common series connectors, the PC software ‘Mconsole’ provides a easy way to control multiple devices, identify device, remotely turn on/off and set DSP function. RS232/RS485/GPIO connectors support device being controlled from third-party system.
Applications
- Sports stadium
- Colleges and universities
- Meeting Room
- Shopping mall
- Hotel
- Airport terminal
Features
- Dante network audio and Dante-Analog backup function
- Built-in DSP processor
- Friendly ‘Mconsole’ GUI software for windows7/8/10/11
- FIR automatic linear magnitude and phase
- Remote on I standby, call amplifier
- Support 100V \ 70V | 82 \ 40
- Free setting to limit power and voltage
- IPS colorful display
- Monitoring temperature \ power \ voltage \ current \ resistance
Front panel
Rear panel
Dante and analog signal backup
1. Connect both analog and Dante signal input interface, and sel-
ect AnalogPri as source, analog signal would be in priority for using.
In events of disconnecting analog source, the amplifier would switch
Dante signal automatically.
2. Connect both analog and Dante signal input interface, and select
DantePri as source, Dante signal would be in priority for using.
Pekase 2172 mes
Theeshold -712 dBu
• Attack time: 1 to 2895ms adjustable;
• Release time: 1 to 2895ms adjustable;
• Threshold level: -90 to OdBu adjustable;
• Click ‘Noise Gate ON’ to enable the setting.
MCONSOLE SOFTWARE
Phase curve: display the phase curve of the current channel.
View: show or hide all balance control points.
Bypass: turn on or off all EQ of the current channel at the same time
Preset: save all the setting parameters of the EQ of the current channel to the computer,
and recall the channel EQ parameter of the computer, which can be recalled across channels
and devices.
Сору: copy the current channel EQ parameter value, which can be pasted to other similar
channels (Note: input channel parameter can only be copied to other input channels).
Paste: used in combination with the copy button to paste the last copied EQ parameter value
to the current channel.
Reset: reset the EQ parameter to the default parameter values.
New project: Restored to the initial open state.
Demo Device: User can view all the functions of the device with-
out affecting the specific device connected.
Open: Open an existing device management project from the
computer disk.
Save: Save the current equipment management project in the
computer disk.
Save as: Save the current equipment management project to the
computer disk.
Save: Select a preset gear from 2~30, and save all
the parameters of the current auto gear to the selected
preset gear.
Recall: Recall the selected preset to the current auto
gear position.
Delete: Delete the existing preset, the default file cannot
be deleted, over written or saved.
Clear: Delete all presets in the device.
Boot: Select a certain preset and set it as the boot file,
each time when the device is restarted, it will automatically
recall the save the parameter; when setting the auto file
to the boot file, the last set parameter will be recall when
device is restarted.
Applications
• Linear of the phase curve of the speaker;
• Match the phase and magnitude of different speaker models within the same product line,
as well as different speaker models in the installation project to make it easier to debug speaker
groups and arrays;
• Dealing with line array systems (for audience area coverage optimization);
• Frequency division optimization to improve the consistency of frequency response of multi-
division speakers over their coverage Angle range.
Devices required:
Documents / Resources
 |
MODE AUDIO NTA3.2DSP Network Dsp Power Amplifier [pdf] User Manual NTA3.2DSP, NTA3.2DSP Network Dsp Power Amplifier, NTA3.2DSP, Network Dsp Power Amplifier, Dsp Power Amplifier, Power Amplifier, Amplifier |