Аюулгүй байдлын чухал заавар
Always read and understand all instructions before operating this band saw. Failure to follow all instructions listed below may result in electric shock, fire, and/or serious personal injury. Save these instructions for future reference.
- Нүдний хамгаалалт зүүх: Always wear safety glasses or goggles that comply with ANSI Z87.1.
- Use Hearing Protection: Prolonged exposure to noise can cause hearing damage.
- Зөв хувцаслах: Do not wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry that could get caught in moving parts. Secure long hair.
- Ажлын талбайг цэвэр байлгах: Эмх замбараагүй газар, вандан сандал нь осол аваарыг урьдаг.
- Аюултай орчноос зайлсхийх: d-д цахилгаан хэрэгсэл бүү ашиглаamp эсвэл нойтон газар, эсвэл бороонд ил гаргах. Ажлын талбайг сайн гэрэлтүүлээрэй.
- Хүүхдийг хол байлгах: Бүх зочдыг ажлын талбайгаас аюулгүй зайд байлгах хэрэгтэй.
- Зөв хэрэгслийг ашиглах: Багаж хэрэгсэл эсвэл хавсралтыг хийгээгүй ажлыг албадуулахгүй байх.
- Багаж хэрэгслийг болгоомжтой арчлах: Хамгийн сайн, аюулгүй ажиллагааг хангахын тулд багаж хэрэгслийг хурц, цэвэр байлга. Дагалдах хэрэгслийг тослох, солих зааврыг дагана уу.
- Цахилгааныг салгах: Always disconnect the power cord before making adjustments, changing accessories, or servicing the tool.
- Аюулгүй ажлын хэсэг: Үргэлж cl ашиглаamps or a vise to hold work. This is safer than using your hand and it frees both hands to operate the tool.
- Гэмтсэн эд анги байгаа эсэхийг шалгах: Багажийг цаашид ашиглахын өмнө хамгаалалт эсвэл эвдэрсэн бусад хэсгийг сайтар шалгаж, энэ нь зөв ажиллаж, зориулалтын функцийг гүйцэтгэх эсэхийг тодорхойлох шаардлагатай.
Тохиргоо ба угсралт
The Delta 28-400 band saw requires assembly before use. It is recommended to have assistance during assembly due to the weight and size of the components.
1. Савлах, шалгах
Carefully remove all components from the packaging. Inspect for any shipping damage. Ensure all parts listed in the packing list are present. The saw, stand, 4-inch dust port, and a 93-1/2 inch blade are included.
Figure 1: The Delta 28-400 Band Saw fully assembled on its stand.
2. Сэндүүдийн чуулган
Assemble the heavy-duty steel stand according to the instructions provided in the separate stand manual. Ensure all bolts are securely tightened. The stand provides a stable base for the band saw.
3. Mounting the Saw to the Stand
With assistance, carefully lift the band saw body and place it onto the assembled stand. Secure it using the provided hardware. Ensure the saw is level and stable on the stand.
4. Blade Installation and Tensioning
- Дээд болон доод дугуйны тагийг нээ.
- Loosen the blade tension knob to allow for blade installation.
- Carefully place the blade around the upper and lower rubber-coated wheels, ensuring the teeth are pointing downwards towards the table.
- Adjust the blade tracking so the blade runs centrally on the wheels.
- Apply appropriate blade tension using the tensioning system. While there isn't a specific tension indicator, ensure the blade is taut enough to prevent twisting during operation.
Зураг 2: Дотоод view showing the upper and lower wheels, and the blade path. This area is critical for blade installation and tracking adjustments.
5. Blade Guide Adjustment
Proper blade guide adjustment is crucial for accurate cuts and blade longevity. The saw features upper and lower blade guides.
- Adjust the upper blade guide assembly so it is approximately 1/8 inch above the workpiece.
- Ensure the side guides are set close to the blade, but not touching, allowing the blade to run freely.
- Adjust the thrust bearing (rear guide bearing) so it is just behind the blade, providing support during cutting without constant contact.
Зураг 3: Ойрын зураг view of the blade and guide bearings, illustrating the components involved in supporting the blade during operation.
6. Table Adjustment
The precision ground cast iron table can tilt from 3° left to 45° right, with a positive stop at 90° for straight cuts.
- Ширээний түгжээний бариулыг суллана.
- Tilt the table to the desired angle. Use a protractor or angle gauge for precise settings if not using the 90° stop.
- Tighten the table locking knob securely before operation.
Figure 4: The band saw table set at a 90-degree angle, ideal for standard straight cuts.
Figure 5: The band saw table tilted to the right, demonstrating its miter capability for angled cuts.
Figure 6: The band saw table tilted to the left, showing the full range of angle adjustments.
7. Power Connection and Voltage Сонголт
The 1 HP TEFC motor can operate on either 115V or 230V. Ensure the motor is wired correctly for your power supply. Consult a qualified electrician if you are unsure about wiring for 230V. Always ensure the power switch is in the OFF position before connecting to power.
8. Тоос цуглуулах
Connect a dust collection system to the 4-inch dust port to maintain a clean work environment and improve visibility. The saw's design includes effective dust collection features.
Ашиглалтын заавар
Before operating, ensure all safety checks are performed, including blade tension, tracking, guide settings, and table angle.
1. Асаах/унтраах
To start the saw, press the green "ON" button. To stop, press the red "OFF" button. Always allow the blade to reach full speed before beginning a cut.
2. Хурдны сонголт
The band saw offers two speeds: 1,620 FPM (Feet Per Minute) and 3,340 FPM. The lower speed is suitable for cutting non-ferrous metals, while the higher speed is for woodworking. Change speeds by adjusting the belt on the two-speed pulley system. Refer to the motor compartment for detailed instructions on changing belt positions.
3. Зүсэлт хийх
- Ensure the workpiece is free of foreign objects (nails, screws).
- Adjust the upper blade guide to be approximately 1/8 inch above the workpiece.
- Ажлын хэсгийг ширээн дээр чанга барина.
- Feed the workpiece slowly and steadily into the blade. Do not force the cut.
- Use a push stick for small pieces or when hands are close to the blade.
- For curved cuts, use a narrower blade and feed slowly, allowing the blade to follow the curve without twisting.
Засвар үйлчилгээ
Regular maintenance ensures the longevity and safe operation of your Delta 28-400 band saw. Always disconnect power before performing any maintenance.
1. Цэвэрлэгээ
- After each use, clear sawdust and debris from the table, blade guides, and inside the wheel covers.
- Use a brush or vacuum cleaner. Do not use compressed air as it can force dust into bearings.
- Keep the motor vents clear of dust to prevent overheating.
2. Ир солих
Replace dull or damaged blades promptly. Follow the blade installation steps in the Setup section. Ensure the new blade is the correct length (93-1/2 inches) and width for your application.
3. Wheel and Bearing Inspection
- Periodically inspect the rubber tires on the upper and lower wheels for wear or damage. Replace if necessary.
- Check the blade guide bearings for smooth operation. Replace any bearings that are seized or excessively worn.
4. Table Surface Care
Keep the cast iron table clean and apply a rust preventative or paste wax periodically to maintain its smooth surface and prevent corrosion.
Алдааг олж засварлах
This section addresses common issues you might encounter with your band saw.
| Асуудал | Боломжит шалтгаан | Шийдэл |
|---|---|---|
| Хөрөө эхлэхгүй байна | No power, tripped circuit breaker, faulty switch, incorrect voltage утас. | Check power connection, reset breaker, inspect switch, verify motor wiring (115V/230V). |
| Blade drifts or cuts inaccurately | Incorrect blade tension, improper blade tracking, worn blade guides, dull blade, base guide block movement. | Adjust blade tension and tracking, inspect and adjust/replace blade guides, replace dull blade. Ensure the base guide block is secure. |
| Хэт их чичиргээ эсвэл дуу чимээ | Loose components, unbalanced wheels, worn bearings, incorrect blade tension. | Check all fasteners, inspect wheels for damage, replace worn bearings, adjust blade tension. |
| Хутга байнга хугардаг | Over-tensioning, improper blade tracking, forcing cuts, incorrect blade for material, worn blade guides. | Reduce blade tension, adjust tracking, avoid forcing cuts, use appropriate blade, check blade guides. |
| Мотор хэт халсан | Blocked motor vents, continuous heavy use, incorrect voltage. | Clean motor vents, allow motor to cool, verify correct voltage утас. |
Үзүүлэлтүүд
Key technical specifications for the Delta 28-400 Band Saw.
- Загварын дугаар: 28-400
- Мотор: 1 HP, 115V/230V, 1 Phase TEFC
- Ирний хурд: 1,620 FPM (low), 3,340 FPM (high)
- Хутганы урт: 93-1/2 инч
- Хүснэгтийн хэмжээ: 15 3/4 in. x 18 7/8 in. precision ground cast iron
- Хүснэгтийн хазайлт: 3° left to 45° right (with positive stop at 90°)
- Тоосны порт: 4 инч
- Материал: Heavy-duty steel frame, aluminum trunnion, cast iron table
- Барааны жин: Ойролцоогоор 165 фунт
- Бүтээгдэхүүний хэмжээ: 45 x 18 x 21 инч (ойролцоогоор, суурьгүй)
- UPC: 847962004819
Баталгаат болон дэмжлэг
For warranty information, technical support, or to order replacement parts, please contact Delta Power Equipment Corporation directly. Refer to your purchase documentation or the official Delta webхамгийн сүүлийн үеийн холбоо барих мэдээлэл болон баталгаат нөхцлийн сайт.
Санал 65 Анхааруулга: This product may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Always follow safety guidelines and wear appropriate personal protective equipment.
Бүтээгдэхүүний албан ёсны видеонууд
No relevant official seller videos were provided for this product in the available data.
