V50.2 Mini Camera Operating Instruction Manual

Mini-Camera-LOGO

V50.2 Mini Camera Operating

V50.2-Mini-Camera-Operating-PRODUCT

OVERVIEW

Use the power and mode switches to charge, record in Video mode or Motion Detection mode, and reset or set the device time. Follow local laws and safety guidance before use.

Quick Setup & Use

  1. Insert a compatible TF memory card (8GB or above). If no card is inserted, the red light flashes for 10 seconds, and the device shuts down automatically.
  2. Charging (built-in battery): connect power using a 5V-1A charger or 5V-1A power bank. During charging, both red and blue flash simultaneously; when fully charged, both remain steadily lit.
  3. Choose mode: set the hardware toggle switch to Video or Motion Detection.
  4. Video recording: press and hold the power button for 2 seconds to turn on and start recording (red flashes twice to indicate recording started). To stop and save, short-press the power button once.
  5. Motion Detection recording: with the device off, set the toggle to Motion Detection, then turn on. Blue flashes rapidly in standby; when motion is detected, recording starts. To stop and save, short-press the power button once.
  6. Night vision light behavior: the infrared night vision function switches on/off automatically based on ambient light levels.

INTRODUCTION

Please read this manual carefully before using the device. Please abide by local laws and do not use this product for any illegal purpose. All consequences shall be borne by you.

Button introduction

V50.2-Mini-Camera-Operating-FIG-1V50.2-Mini-Camera-Operating-FIG-2

Pre-Operation Notes
  1. No memory card inserted: The red light will flash for 10 seconds, and then the device will shut down automatically.
  2. Card requirement: The device memory card must be 8GB or above. Data cannot be saved normally on cards with less than 8GB capacity.
  3. Startup behavior: After power-on, the device automatically enters either Video Mode or Motion Detection Mode based on the hardware switch position.

Product parameters

  • Video format: AVI
  • Video coding: M-JPEG
  • Video resolution: 1920*1080
  • Video frame rate: 30fps
  • Motion detection record: support
  • Battery capacity: about 1500mAh
  • Record time: about 520 minutes
  • Charge voltage: DC 5V 1A
  • Storage support: 8GB-128GB
  • Transmission speed: USB 2.0
  • Interface type: Type-С
  • Storage temperature: – 10-40 °C
  • Working humidity: 15-85% RH9

Product operation

The following operation is based on inserting the TF card correctly.

  1. Charging:
    • This device has a built-in rechargeable lithium battery. When the device is short of power, it can be charged in the following ways:
      1. Connect the 5V-1A charger;
      2. Connect the mobile power bank (5V-1A);
    • Note: the red and blue lights flash at the same time when charging. When fully charged, the red and blue lights are on.
  2. Power on&Power off
    • On: press the power button for 2 seconds.
    • Off: Press the power button for 5 seconds to turn off the device.
  3. Video:
    • Video: Push the button to theposition, and press the power button for 2 seconds. The device is powered on; the red and blue lights are on, then the blue light is off, and the red light flashes twice and goes off to enter the video recording.
    • Save: While recording, click the power button once to stop and save the recording; the red light will be on, and the device will return to standby mode.
    • One paragraph,5 minutes, supports loop recording.
  4. Motion Detection Mode:
    • When powered off, push the button toV50.2-Mini-Camera-Operating-FIG-4 set the position.
    • After power on, it will automatically enter the motion detection mode.
    • In this mode, the blue light flashes fast; the device is in the detection state. Once it detects any moving objects within the range, the blue light flashes slowly, and the device enters video recording. After 2 minutes, the recording will be saved automatically. If there is no moving object, the device will return to the detection state, and the blue light will flash fast.
    • Exit: Click the power button once to stop and save the video; return to standby mode; the blue light is on.
    • Note: Motion detection recording, one paragraph, 2 minutes.
    • Detecting state: blue indicator flashes fast; Recording state: blue indicator flashes slowly.
  5. Infrared night vision lights switch:
    • The infrared night vision function will automatically turn on or off according to the brightness of the device’s surrounding environment. No need to switch manually.
    • Note: During operation, press the power button for 3 seconds, and the blue light flashes three times to turn it off.
  6. Record with charging:
    • When the device is powered off, connect the device to a power source(the charger or power bank), and the red and blue lights flash at the same time; the device is in the charging state. Then click the power button once; the device will enter video mode or motion detection mode. Click the power button again to exit the recording and save it.
    • If there is no operation within 5 seconds in the standby mode while charging, it will return to the charging state.
    • Note: The device can’t enter the video mode when connected to the computer.
  7. Reset:
    • In case of system error or malfunction, reset the device by inserting a pin into the reset hole.
  8. Time setting:
    1. Upon power-on, the device will generate a time file named “TIME.TXT” in the system.
    2. TURN OFF the device and connect it to a computer.
    3. Locate the “TIME.TXT” file, set the desired time using the format 2023–05–01 18:18:18 Y, and save the file.
    4. Disconnect the device from the computer, then turn on the device. The time set is then complete.
      • If you want to cancel the time stamp. Modify “Y” in the “TIME.TXT” file to “N” to disable the time display.
      • The reference format is as follows:
      • 2023-05–01 18:18:18 Y (with time watermark display)
      • 2023-05-01 18:18:18 N (no time watermark display)

Disclaimer

  1. The usage of this device is subject to the relevant national laws and regulations. DO NOT use this product for any illegal activities.
  2. DO NOT point the camera lens at direct sunlight, or permanent damage may occur.
  3. Keep away from fire. Never expose the device to any fire source.
  4. DO NOT disassemble or modify. Doing so causes the risk of electric shock, burn injury, and other health-related hazards.
  5. DO NOT let water, liquids, or foreign matter get inside the device. Extra precaution is advised when it is raining, snowing, near the ocean, or near other forms of water. In case any of the symptoms are present, turn off the device immediately and contact us for further support.
  6. DO NOT drop the device, or permanent damage may occur.

Troubleshooting

  • No memory card inserted: The red light flashes for 10 seconds, then the device shuts down automatically. Insert a TF card with a capacity of 8GB or above.
  • Device not charging as expected: During charging, both red and blue lights should flash simultaneously; when fully charged, both should remain steadily lit.
  • Can’t start recording while connected to a computer: The device cannot enter video recording mode when connected to a computer.
  • System error/crash/malfunction: Insert a pin into the RST (reset) hole to restart the hardware.

Documents / Resources

PDF thumbnailV50.2 Mini Camera Operating
Instruction Manual · Mini Camera, V50.2, camera

References

Ask a Question

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

Ask a Question

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.