MICRO ENE M1260F28 Remote Control User Guide
Important
- Always press and hold the button to ensure the signal is sent successfully.
- For best results, use within 16 ft and point directly at the red light therapy
lamp (receiver).
Switch On/Off
ON: Switch on the lamp and it will automatically restores to the last used settings (wavelengths, timer, brightness etc.,). The 
and ON icons will appear on the display.
FF: Switch off the lamp, and it will automatically record the current settings. The icon will disappear from the screen, and the OFF icon willappear.
Wavelengths
- 660nm: Red Light – The display screen shows 660, and the
icon appears. The red indicator lights on the rail will also light up. - 850nm: Near-Infrared Light – The display screen shows 850, and the icon appears. The blue indicator lights on the rail willalso light up. (Note: This wavelength light is invisible to the eyes.)
- 660nm + 850nm: Combination -The display shows 6685, and the icon appears. Both red & blue indicator lights will light up.
Brightness Adjustment
- Adjustable brightness range: 5%-100%
- Each time you press the Brightness button, the level increases by 5%. Press and hold the button to adjust continuously. When it reaches 100%, pressing again will reset it to 5% and continue increasing.
- The
icon on the display screen will appear. The screen will show the current brightness level
Quick Brightness Levels
- 100%/80% /30%: Press once to switch directly to the factory preset brightness levels.
Countdown Timer (Auto Off)
- Auto Off at: 10/15/20 minutes
- Timer Setup:
- Press the timer button
to activate the timer. The .
icon on the display screen will flash. - Press the timer button again to select the auto off time.
- Wait 3 seconds for the selected off-time to be confirmed. 100% 80% 30% Once confirmed, the icon will stop flashing and remain steadily. on.
- The 888 icon on the display screen counts down until 0; the lamp turns off automatically.
- If you need to adjust the timer duration again, press the timer button on the remote control to select and switch to a new setting.
- During the timer countdown, you can press the OFF button to turn off the light at any time.
- You may adjust brightness and wavelength while the timer running. The light will still turn off at the set time.
Toitty the lanp dom not hve a slenys on mode. Thе mwтam ecarnerded 20us ee san off the lam aftar
This device complies with part 15 of the FCC Rules.Operation is subject to the following two conditions:
(1)this device may not cause harmful interference.and(2)this device must accept any interference received.including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment.
NOTE:This equipment has been tested and found to comply with the limits for a Class B digital device.pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates,uses and can radiate radio frequency energy and.if not installed and used in accordance with the instructions.may cause harmful interference to radiocommunications.However.there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception.
which can be determined by turning the equipment off and on.the user is encouraged to try to correct the interference by one or more of the following measures:
–Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and receiver.
–Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
–Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement.The device can be used in portable exposure condition without restriction
Documents / Resources
 |
MICRO ENE M1260F28 Remote Control [pdf] User Guide 2BRWO-M1260F28, 2BRWO-M1260F28, M1260F28, M1260F28 Remote Control, M1260F28, Remote Control, Control |