HR5 RF Wireless Dimmer 5 in1 Smart LED Strip Controller
“
Specifications
- 5 in 1 LED Controller (2.4GHz)
- 16 Million colors to choose
- Color temperature adjustable
- Dim brightness / Saturation
- 2.4G RF wireless transmission technology
- Remote control distance: 30m
- Supports Smartphone app control (2.4GHz gateway is needed)
- Supports third party voice control (2.4GHz gateway is
needed) - DMX512 controllable (Only for RGB+CCT output mode, DMX512 LED
transmitter is needed)
Product Usage Instructions
Set up Output Mode
Set up the correct output mode based on the feature of
lights:
Sensing method: Press the SET button
continuously to switch output mode. It will log out without
operation within 3 seconds.
| Indicator Color | Output |
|---|---|
| White Light | Single Color |
| Yellow Light | Dual White |
| Red Light | RGB |
| Green Light | RGBW |
| Blue Light | RGB+CCT |
PUSH Dimming
Short press PUSH switch: Turn ON/OFF light.
Long press PUSH switch: Stepless dimming
brightness. Long press and release your finger, then repeat long
pressing to increase or decrease brightness.
Compatible with Remote Controls
This product is compatible with the following 2.4G RF remote
controls (Purchased separately): FUT100, FUT089S, FUT089, FUT088,
FUT092, FUT096, B8, FUT089-B, FUT092-B, FUT096-B, B0/B0-B,
B4/B4-B/T4, B3/B3-B/T3, S2W+, WL-Box2.
2.4G RF Remote Control Instructions
-
- Linking Code Instructions:
- Press Link/Unlink button.
- Power off for 10 seconds and power on again or short press SET
once or turn on light via PUSH switch. - Lights blink 3 times slowly means linking is done
successfully.
- Linking Code Instructions:
…
Frequently Asked Questions (FAQ)
Q: What is the remote control distance for this product?
A: The remote control distance is 30 meters. Additionally, one
light can transmit signals from the remote control to another light
within 30 meters.
“`
Subordinate New Brand
5 in 1 LED Controller ( 2.4GHz ) Instrucon Manual
Contents
Product features …………………………………………………………………………… 2 Set up output mode …………………………………………………………………….. 3 PUSH Dimming …………………………………………………………………………….. 3 Compable with remote ……………………………………………………………… 3 2.4G RF remote control instrucon ……………………………………………. 4-7
Link / Unlink Instrucons …………………………………………………………… 4 Auto transming & Synchronizaon …………………………………………… 5 Dynamic mode table selecon ………………………………………………….. 5 PWM frequency switching ………………………………………………………… 6 “Do Not Disturb” mode is acvated and shut down …………………….. 7 DMX512 LED transmier control instrucon ………………………………….. 8 Aenon …………………………………………………………………………………….. 9
Product features
Made by new 2.4GHz wireless transming technology with low power consumpon, strong ability to build network automacally and an-interference. with MiBoxer 2.4GHz gateway to get wireless dimming color, remote control, ming control, group control, music rhythm funcon. Support 2.4G RF remote control.
16 Millions of colors to choose Color temperature adjustable Dim brightness / Saturaon 2.4G RF wireless transmission technology Remote control distance 30m Auto-transming & Synchronizaon Support Smartphone app control (2.4GHz gateway is needed) Support third party voice control (2.4GHz gateway is needed) DMX512 controllable (Only for RGB+CCT output mode DMX512 LED transmier is needed)
2
Set up output mode
Set up correct output mode based on the feature of lights Seng method: Press “SET” buon connuously to switch output mode (aenon: it will log out without operaon within 3 seconds)
Output mode sheet ( confirm output mode based on color of indicator)
Indicator color White Light Yellow Light Red Light Green Light Blue Light
Output
Single Color Dual White
RGB
RGBW RGB+CCT
PUSH Dimming
Short press PUSH switch: Turn ON/OFF light
Long press PUSH switch: Stepless dimming brightness. Long press and release your finger, then repeat long pressing to increase or decrease brightness.
PUSH
Compable with these 2.4G RF remote controls (Purchased separately)
FUT100
FUT089S FUT089
FUT088
FUT092
FUT096
B8
FUT089-B
FUT092-B FUT096-B
B0 / B0-B
B4 / B4-B / T4
B3 / B3-B / T3
3
S2W+
WL-Box2
2.4G RF Remote control instrucon
1). Linking Code Instrucons
Power
Light
or
SET
or PUSH
1
Link / Unlink buon
2
Power off 10 seconds and Short press ” I ” buon power on again or short press 3 mes within 3 seconds. “SET” one me or turn on light via PUSH switch
Power
Light
3
Lights blink 3 mes slowly means linking is done successfully.
Linking failed if light is not blinking slowly, Please follow above steps again. (Note: Light that have linked can’t link again)
2). Unlinking Code Instrucons
Power
Light
or
SET
or PUSH
1
Link / Unlink buon
2
Power off 10 seconds and power on again or short press “SET” one me or turn on light via PUSH switch
Short press ” I ” buon 5 mes within 3 seconds
Power
Light
3
Lights blink 10 mes quickly means unlinking is done successfully.
Unlinking failed if light is not blinking quickly, Please follow above steps again. (Note: Light haven’t linked that don’t need to unlink)
4
3). Auto transming & Synchronizaon (only for remote control)
Remote signal auto transming One light can transmit the signals from the remote control to another light within 30m, as long as there is a light within 30m, the remote control distance can be limitless.
Dynamic modes auto synchronizaon Mul lights can synchronize if they are in same dynamic mode and linked with same remote (distance between each light is within 30m)
Auto transming / Modes auto synchronizaon
Controller
Distance 30m
Controller
4). Dynamic mode table selecon (only for remote control) Select dynamic mode table 1: While the light is in stac mode, short press ” S+ ” buon 5 mes quickly unl blue light flashes 3 mes slowly, stac mode is acvated successfully. Select dynamic mode table 2: While the light is in stac mode, short press ” S- ” buon 5 mes quickly unl yellow light flashes 3 mes slowly, stac mode is acvated successfully.
Dynamic mode table 1 (default)
Number 1 2 3 4 5 6 7 8 9
Dynamic Mode Mardi Gras Automac color change Sam Gemstone Twilight American Fat Tuesday Party Slow Color Splash
Brightness / Saturaon / Speed Adjustable
5
Dynamic mode table 2 (need to switch manually)
Number 1
Dynamic Mode Seven colors gradual change
Brightness / Saturaon / Speed
2
White light Gradual change
3
RGB gradual change
4
Seven colors jump to change
5
Jump to change randomly
6
Red light gradual change +Flash 3 mes
7
Green light gradual change +Flash 3 mes
Blue light gradual change
8
+Flash 3 mes
9
White light gradual change +Flash 3 mes
Adjustable
5). PWM high frequency / low frequency switching (only for remote control)
Switch to high frequency: Press “OFF” buon 1 me within three seconds and press “ON” buon 5 mes, Acvated successfully once led light flashes 2 mes quickly.
Switch to low frequency: Press “ON” buon 1 me within three seconds and press “OFF” buon 5 mes, Acvated successfully once led light flashes 2 mes slowly.
6
6). “Do Not Disturb” mode is acvated and shut down (default acvated)
Turn on “Do Not Disturb” mode (wide using in the area which have power failure frequently to save energy) 2.4G RF Remote turn on and turn off instrucon
Turn on “Do Not Disturb” mode: Press “OFF” buon three mes within three seconds and press “ON” buon three mes, Acvated successfully once led light flashes four mes quickly. Aenon: Do not disturb mode is acvated 1. When the light is OFF status (For example: Use app or remote to turn off light)
The light is OFF status once you turn off power and turn on again. (User must turn off and turn on power twice mes to acvate light or use APP / remote to acvate light) 2. When the light is ON status The light is ON status once you turn off and turn on power one me.
Turn off “Do Not Disturb” mode: Press “ON” buon three mes within three seconds and press “OFF” buon three mes, closed successfully once led light flashes four mes slowly. Aenon: The light will be always “ON” status if you turn on and turn off power once user closed “Do Not Disturb” mode.
7
DMX512 LED Transmier Control (Purchased separately)
Only for RGB+CCT output mode
2.4GHz Wireless Signal
1 Zone
Limitless
+
SET 8.8.8.8
DMX512 Transmier
+
Connect
DMX512 Control Panel
16 Zone
Limitless
DMX512 LED Transmier Link/Unlink
1 Follow instrucon of DMX512 transmier (FUTD01), Choose the zone for the light by pressing ” + ” or ” – ” (e.g. “CH12″ means zone 12)
Power
SET Link/Unlink buon
SET
Power
2
3
4
Link
The controller is powered off for 10 seconds and then powered on, or press ” SET ” buon 1 me.
Short press ” SET ” 3 mes within 3 seconds while the indicator of controller is ON
Link is done once indicator of controller flashes 3 mes slowly
Unlink
The controller is powered off for 10 seconds and then powered on, or press ” SET ” buon 1 me.
Short press ” SET ” 5 mes within 3 seconds while the indicator of controller is ON
Unlink is done once indicator of controller flashes 10 mes quickly
If the link or unlink failed, please follow the above steps again.
8
Aenon
1. Please turn off power supply before installaon. 2. Please ensure input voltage to be same as requirements from device. 3. Don’t disassemble device if you are not expert, otherwise it will damage it. 4. Please do not use the light in the place with widely range metal area or strong electromagnec
wave nearby, otherwise, the remote distance will be seriously affected.
Scan QR code to watch 2.4GHz series video instrucon Or enter into following link directly hps://miboxer.com/light/video/1pc_remote.html
Made in China
Documents / Resources
 |
MiBOXER HR5 RF Wireless Dimmer 5 in1 Smart LED Strip Controller [pdf] Instruction Manual HR5-RF-Wireless-Dimmer-5-in1-Smart-LED-Strip-Controller, 5 in 1 LED Controller 2.4GHz, DMX512 LED transmitter, HR5 RF Wireless Dimmer 5 in1 Smart LED Strip Controller, HR5 RF, Wireless Dimmer 5 in1 Smart LED Strip Controller, 5 in1 Smart LED Strip Controller, LED Strip Controller, Strip Controller, Controller |
