DMX512 Constant Voltage Waterproof RDM Decoder
“
Specifications
- Product Name: D4-WPS 4 Channel Constant Voltage Waterproof
DMX512 & RDM Decoder - IP Rating: IP67
- Channels: 4 DMX channels selectable
- Grey Level: 16bit (65536 levels) / 8bit (256 levels)
selectable - PWM Frequency: 250/500/1000/2000/4000/8000/16000/32000Hz
selectable - Dimming Curve: Logarithmic or linear selectable
- Operating Temperature: -20°C to +55°C
- Dimensions: L165 x W98 x H72mm
- Weight: 0.492kg
Product Usage Instructions
Installation and Wiring
1. Connect the DMX input and output cables according to the
provided wiring diagram.
2. Ensure proper power input within the range of 12-48VDC.
3. Make sure to follow the safety and EMC standards during
installation.
System Parameter Setting
1. Long press SETUP key for 2s to prepare for setting system
parameters.
2. Use short presses of the SETUP key to switch between decode
mode, grey level, PWM frequency, brightness curve, default output
level, and automatic blank screen.
3. Set decode mode by short pressing the keys to switch between
1/2/4 channel decode mode.
4. Adjust grey level by short pressing the keys to switch
between 8bit or 16bit.
5. Select the desired PWM frequency by short pressing the keys
to switch between available options.
FAQ
1. Do I need a DMX signal amplifier for this decoder?
If more than 32 decoders are connected or if using overlong
signal lines, a DMX signal amplifier is required.
2. How can I troubleshoot the recoil effect due to longer
signal lines?
You can try connecting a 0.25W 90-120 terminal resistor at the
end of each DMX signal line to address the recoil effect.
3. What do the overload alarms displayed on the decoder
signify?
The display of 1OL, 2OL, 3OL, 4OL corresponds to 1, 2, 3,
4-channel overload alarms respectively. OHA indicates an overheat
alarm.
“`
D4-WPS
4 Channel Constant Voltage Waterproof DMX512 & RDM Decoder
Waterproof DMX512 decoder with IP67 rating, suitable for outdoor and damp environment.
Comply with the DMX512/RDM standard protocols. Digital numeric display, set DMX decode start address by buttons. 1/2/4 DMX channel output selectable. 16bit (65536 levels) /8bit (256 levels) grey level selectable. PWM frequency 250/500/1000/2000/4000/8000/16000/32000Hz selectable. Logarithmic or linear dimming curve selectable. Stand-alone RGB/RGBW mode and 4 channel dimmer mode selectable,
which be controlled by buttons with built-in programs, instead of DMX signal. Over-heat / Over-load / Short circuit protection, recover automatically.
DMX512
Technical Parameters
Input and Output
Input voltage Input current
12-48VDC 20.5A
Output voltage
4 x (12-48)VDC
Output current
4x5A@12/24V, 4x4A@36/48V
Output power Output type
240W@12V, 480W@24V, 576W@36V, 768W@48V Constant voltage
Safety and EMC EMC standard
Safety standard Certi cation Package Size Gross weight
Mechanical Structures and Installations
EN IEC 55015/ EN IEC 61547 EN 61347-1/-2 EN 62493 CE RoHs
L165 x W98 x H72mm 0.492kg
DMX Input Brown D+ Blue DGray GND
DMX Output Purple D+ Y/G DBlack GND
D4-WPS DMX512 & RDM Decoder
Uin=12-48VDC Iin=20.5A Uout=4x(12-48)VDC Iout=4x5A@12/24V
4x4A@36/48V Pout=240W@12V 480W@24V
576W@36V 768W@48V Temp Range: -20~+55 ·tc=75
MODE SETUP
Wiring Diagram
IP67
DMX RDM
Power Input
Brown V+ Blue V-
LED Output
Black
V+
Brown 1 R WW
Y/G
2 G CW
Blue
3 B WW
Gray
4 W CW
57.00 mm
Warranty and Protection Warranty
Protection
Environment Operation temperature Case temperature (Max.) IP rating
5 years Reverse Polarity, Over-heat Over-load, Short circuit
Ta: -20 OC ~ +55OC Tc: +75OC IP67
153.00 mm
143.50 mm 34.00 mm
DMX Master
Power Supply 12-48VDC Constant Voltage
AC100-240V
DMX decoder
RGBW LED strip
W
Note: 1. An DMX signal amplifier is needed if more than 32 decoders are connected, or use overlong signal line,
signal amplification should not be more than 5 times continuously. 2. If the recoil effect occurs because of longer signal line or bad line quality, please try to connect
0.25W 90-120 terminal resistor at the end of each DMX signal line. 3. When display 1OL,2OL,3OL,4OL, correspond to 1,2,3,4, channel overload alarm. When display OHA, overheat alarm.
Operation
System parameter setting Long press SETUP key for 2s, prepare for setup system parameter: decode mode, grey level, output PWM frequence, output brightness curve, default output level,
automatic blank screen. then short press SETUP key to switch six item. Decode mode: short press or key to switch 1/2/4 channel decode mode(“d-1″,”d-2” or “d-4”). When set as 1 channel decode,
the decoder occupy only 1 DMX address, and four channel output the same brightness of this DMX address. Grey level: short press orkey to switch 8bit(“b08”) or 16 bit(“b16”). choose 16 bit if the DMX master support 16 bit. Output PWM frequency: short press or key to switch 250Hz(“F02”), 500Hz(“F05”), 1000Hz(“F10”), 2000Hz(“F20”), 4000Hz(“F40”), 8000Hz(“F80”),
16000Hz(“F16”) or 32000Hz(“F32”). Higher PWM frequency, will cause lower output current, higher power noise, but more suitable for camera(No ickers for video). When PWM frequency > 8000Hz, it is necessary to reduce the output current per channel (4x3A@12-48V at 16000Hz; 4×2.5A@12-24V and 4x2A@36-48V at 32000Hz). Output brightness curve: short press or key to switch linear curve(“C-L”) or logarithmic curve(“C-E”). Default output level: set output level when no DMX input signal. short press or key to switch maintain DMX output(“d- -“) or output default level (“d00” to “dFF”, 0-100%), long press or key to change output default level. Automatic blank screen: short press or key to switch enable (“bon”) or disable(“boF”) automatic blank screen.
User Manual Ver 1.0.3 2025.8
Page 1
Long press SETUP key for 2s or timeout 10s, quit system parameter setting. Note: In addition to manual button operation settings, the above system parameters can also be set by RDM function.
DMX mode Short press MODE key, when display 001~512, enter DMX mode. Press or key to change DMX decode start address(001~512), long press for fast adjustment. If there is a DMX signal input, will enter DMX mode automatically. DMX Dimming: Each D4-WPS DMX decoder occupy 4 DMX address when connecting the DMX console.
For example, the defaulted start address is 1, their corresponding relationship in the form:
DMX Console CH1 0-255 CH2 0-255 CH3 0-255 CH4 0-255
DMX Decoder Output
CH1 PWM 0-100% (LED R) CH2 PWM 0-100% (LED G) CH3 PWM 0-100% (LED B) CH4 PWM 0-100% (LED W)
DMX mode (001~512)
Stand-alone RGB/RGBW mode
Enter stand-alone RGB/RGBW mode only when DMX signal is disconnected or lost. Short press MODE key, when display P01~P30, enter stand-alone RGB/RGBW mode. Press or key to change dynamic mode number(P01~P30). Each mode can adjust speed and brightness.
Short press SETUP key for switch between mode speed, brightness and W channel brightness setting. Press or key to setup value of each item. Mode speed: 1-10 level speed(S-1, S-9, S-F). Mode brightness: 1-10 level brightness(b-1, b-9, b-F). W channel brightness: 0-255 level brightness(400-4FF). Long press SETUP key for 2s, or timeout 10s, quit setting.
Stand-alone RGB/RGBW mode (P01~P30)
Speed
Brightness
(8 level) (10 level,100)
Stand-alone dimmer mode
Enter stand-alone dimmer mode only when DMX signal is disconnected or lost. Short press MODE key, when display L-1~L-8, enter stand-alone dimmer mode. Press or key to change dimmer mode number(L-1~L-8). Each dimmer mode can adjust each channel brightness independently.
Short press SETUP key to switch between 4 channel(100~1FF, 200~2FF, 300~3FF, 400~4FF). Press or key to setup brightness value of each channel. Long press SETUP key for 2s, or timeout 10s, quit setting.
Stand-alone dimmer mode (L-1~L-8)
Restore factory default parameter
Long press and key for 2s, restore factory default parameter, display”RES”. Factory default parameter: DMX decode mode, DMX decode start address is 1, four channel decode, 8 bit grey level, 2000Hz PWM frequence output,
logarithmic brightness curve, output 100% level when no DMX input, RGB mode number is 1, dimmer mode number is 1, disable automatic blank screen.
RGB Change Mode List
No.
Name
P01
Static red
P02
Static green
P03
Static blue
P04
Static yellow
P05
Static cyan
P06
Static purple
P07
Static white
P08
RGB jump
P09
7 color jump
P10
Red strobe
No. P11 P12 P13 P14 P15 P16 P17 P18 P19 P20
Name
Green strobe Blue strobe White strobe RGB strobe 7 color strobe Red fade in and out Green fade in and out Blue fade in and out White fade in and out RGBW fade in and out
Malfunctions Analysis & Troubleshooting
No. P21 P22 P23 P24 P25 P26 P27 P28 P29 P30
Name Red yellow smooth Green cyan smooth Blue purple smooth Blue white smooth RGB+W smooth RGBW smooth RGBY smooth Yellow cyan purple smooth RGB smooth 6 color smooth
Malfunctions No light Wrong color Uneven intensity between front and rear,with voltage drop
Causes 1. No power. 2. Wrong connection or insecure. 1. Wrong connection of R/G/B/W wires. 2. DMX decode address error. 1. Output cable is too long. 2. Wire diameter is too small. 3. Overload beyond power supply capability. 4. Overload beyond controller capability.
Troubleshooting 1. Check the power. 2. Check the connection. 1. Reconnect R/G/B/W wires. 2. Set corrrect decode address. 1. Reduce cable or loop supply. 2. Change wider wire. 3. Replace higher power supply. 4. Add power repeater.
User Manual Ver 1.0.3 2025.8
Dimming Curve Setting
PPW WMM dduutty(y(%)%)
Linear dimming curve
110000 9900 8800 7700 6600 5500 4400 3300 2200 1100
Gamma=1.0
10 20 30 40 50 60 70 80 90 100
Brightness(%)
Logarithmic dimming curve
100
Gamma=1.6
90 80 70 60 50 40 30 20 10
10 20 30 40 50 60 70 80 90 100
Brightness(%)
PWM duty(%)
Page 2
Documents / Resources
 |
MIBOXER DMX512 Constant Voltage Waterproof RDM Decoder [pdf] Owner's Manual D4-WPS, DMX512 Constant Voltage Waterproof RDM Decoder, DMX512, Constant Voltage Waterproof RDM Decoder, Waterproof RDM Decoder, RDM Decoder, Decoder |