xylem FlexNet CommandLink II Wireless Interface User Guide

Aratohu Tere
AQG-10087-05
FlexNet CommandLink II

FlexNet CommandLink II Wireless Interface

The CommandLink® II wireless interface provides access to a complete suite of functional controls within a gas, water, or electric SmartPoint® transceiver. This Bluetooth® enabled device, coupled with a handheld, can perform activations, deactivation, meter read, on-demand reads, and audits of the SmartPoint module.

Whakatupato: Risk of hot surface. Do not hold the device longer than one (1) minute when operating in an ambient temperature above 40°C (104°F).

Hipanga 1: Me utu te CommandLink II
You must charge the CommandLink II completely before first use.

1. Plug the charging adapter into a power outlet and connect to the Charging Port located next to the Mag Loop on top of the Command Link II.
   Tuhipoka: Make sure you have rechargeable batteries installed before using a power outlet.
   Ko nga waeine he papahiko kore e taea te whakahoki, kaua rawa e kuhu ki te putanga hiko mo te utu.
2. Ka whakamarama te tohu LED whero, e tohu ana kei te utu te waeine.
3. Unplug the unit when the red LED is no longer illuminated, indicating the CommandLink II is fully charged.
   Tuhipoka: To power down the CommandLink II immediately, press and hold the power button located on the side of the CommandLink II until the PWR LED turns off.

Hipanga 2: Tahurihia te Hononga Whakahau II

1. Patohia te paatene mana.
2. Ka whiti te rama LED kakariki i te wa e pai ana te mana o CommandLink II.

Hipanga 3: Waihangahia he hononga Nihokikorangi
To use the CommandLink II, you must first establish a Bluetooth partnership with a Windows Mobile, Android, or iOS-equipped handheld device (HHD) or PC.

Ihirangi mokete

• FlexNet CommandLink II
• Nga here Bungee (2)
• Pūurutau Whakatau (AC/DC)
• Pūurutau Whakatau Waka (DC/DC)
• Take

Mēnā kei te whakamahi i tētahi Pūrere Pukoro Pukoro Windows:

1. Tīpakohia Tīmata, ka Tautuhinga.
2. Select Connections, then select Bluetooth COM.
   Power on the CommandLink II if it is off.
3. Tīpakohia te Rapu Pūrere.
   A list of all the Bluetooth-enabled devices in range is generated and displayed.
   If your CommandLink II does not appear in the list, make sure that it is powered on. If it is powered on, power cycle it and select Discover Devices again, and repeat this step.
4. Tīpakohia to
   CommandLink II from the list and select Connect.
5. If you are prompted toSet the Bluetooth PIN, enter 0000 and select OK.
6. Tīpakohia ĀE kia puta.
7. Tīpakohia X i te kokonga matau o raro ki te puta.
8. Tīpakohia Utauta FieldLogic mai i te tahua Tīmata.
9. From the FieldLogic Tools main screen, select Menu, and select Options.
10. Tīpakohia te ripa FlexNet ka kowhiria te Hononga Whakahau mai i te rarangi takaiho momo Pūrere. Kaua e tohua CLxxxxxxxx_BLE.
11. Tīpakohia Tiki Tūnga. Ko nga Utauta FieldLogic e hono ana ki te CommandLink II ka whakaatu i te karere angitu.
12. Tīpakohia OK.
13. Tīpakohia anō ĀE kia hoki ki te mata Tūhono.

Mena kei te whakamahi i tetahi Pūrere Android:

1. Tīpakohia te tohu Tautuhinga.
2. Select Options, then select FlexNet. FieldLogic displays a list of available devices.
3. Tīpakohia + ki view te mata takirua pūnaha.AQG – 10007 – 05
4. Tīpakohia to CommandLink II (CLxxxxxxxx) mai i te rarangi o nga taputapu Nihokikorangi e waatea ana.
5. Tīpakohia te takirua. Ko to CommandLink II ka whakaatu ki te rarangi Pūrere Paihere.
6. Hoki ki nga Utauta FieldLogic.
7. Select the newly-paired CommandLink II in the list and select the information symbol.Ka hono a FieldLogic ki te CommandLink II ka whakaatu i te karere angitu.
8. Tīpakohia Kati.
9. Tīpakohia te pere o muri kia hoki ki te mata matua FieldLogic.

Mena kei te whakamahi i tetahi Pūrere-a-ringa a iOS:

1. Tīpakohia te tohu Tautuhinga.
2. Tīpakohia nga Kōwhiringa, ka kowhiria te FlexNet. Ka tirotirohia e FieldLogic te taputapu ka whakaatu i nga taputapu e waatea ana. Ka tāmata aunoa te rārangi.
3. Ka whakaatuhia he matapihi pakū-ake whakaaetanga. Tīpakohia OK.
4. Tīpakohia to CommandLink II (CLxxxxxxxx) mai i te rarangi o nga taputapu Nihokikorangi e waatea ana.
   
5. Select your CommandLink II and then select the information symbol.
6. Ka hono a FieldLogic ki te CommandLink II ka whakaatu i te karere angitu.
7. Tīpakohia Katia kia hoki ki te mata Kōwhiringa.
8. Tīpakohia te pere o muri kia hoki ki te mata matua FieldLogic.

Mena kei te whakamahi PC:

1. Whakakahangia te CommandLink II.
2. Tīpakohia te ata Nihokikorangi i runga i te papamahi o to rorohiko mai i te tahua Tīmata ranei.
3. Mai i te pihanga Pūrere Nihokikorangi, tohua Tāpirihia he taputapu.
4. Ka rapua e to rorohiko nga taputapu hei taapiri.
5. Select the icon containing the CommandLink II ID number (CLxxxxxxxx).
   Tuhipoka: If two numbers appear, make sure you select CLxxxxxxxx. Do not select CLxxxxxxxx_BLE.
6. Tīpakohia Panuku.
7. Your computer confirms the successful addition of the CommandLink II.
8. Tīpakohia Katia ki te haere tonu.
9. Tīmata Utauta FieldLogic. Mai i te mata matua, tīpako Utauta ka tīpako Kōwhiringa.
10. Tīpakohia te Whakawhanui Tautuhinga FlexNet ka kowhiria te CommandLink mai i te rarangi taka-iho o te Pūrere Whakawhitiwhiti. Tīpakohia tō pūrere mai i te rārangi taka-iho ingoa Pūrere.
11. Select Get Status.
    FieldLogic Tools connects with the CommandLink II and displays a success message.
12. Tīpakohia ĀE kia hoki ki te mata Kōwhiringa.
13. Tīpakohia ĀE kia hoki ki te mata Tūhono.

Attach a Strap to the CommandLink II

To attach a strap, slide it in between the slots on the sides of the unit.

AQG – 10007 – 05

Tauākī Tautukunga

WHAKAARO
Any modifications made to this device that are not approved by Sensus may void the authority granted to the user by the FCC to operate equipment.

WHAKAARO
Mo te karaehe B – Radiators Pohehe:
This device complies with Part 15 of the FCC Rules. Operation is subjectto the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.

WHAKAARO
Panui ICES-003 Class B—Avis NMB-003, Class B
Ko tenei taputapu matihiko Class B e ū ana ki te Canadian ICES-003.

WHAKAARO
Tuhipoka: Kua whakamatauria tenei taputapu, kua kitea e u ana ki nga rohe mo tetahi taputapu matihiko Class B, i runga i te Wahanga 15 o nga Ture FCC.
I hangaia enei rohe ki te whakarato i te whakamarumaru tika mai i nga pokanoa kino i roto i te whakaurunga whare. Ka whakaputa, ka whakamahi, ka taea e tenei taputapu te whakaputa i te kaha auau reo irirangi, a, ki te kore e whakauruhia, ka whakamahia i runga i nga tohutohu, ka raru pea nga korero reo irirangi. Heoi ano, karekau he taurangi ka kore e puta he pokanoa ki tetahi whakaurunga. Mena ka raru nga taputapu i runga i te reo irirangi, pouaka whakaata ranei, ka taea te whakatau ma te whakaweto i nga taputapu, ka akiakihia te kaiwhakamahi ki te ngana ki te whakatika i te pokanoa ma te kotahi, neke atu ranei o nga tikanga e whai ake nei:

• Whakahoahoa, nukuhia ranei te antenna whiwhi
• Whakanuia te wehenga i waenga i nga taputapu me te kaiwhiwhi
• Honoa te taputapu ki tetahi putanga i runga i te ara iahiko rereke mai i tera e honoa ana te kaiwhiwhi
• Korero atu ki te kaihoko, ki tetahi tohunga hangarau reo irirangi/TV mo te awhina

WHAKAARO
Ka whai tenei taputapu ki nga paerewa RSS kua whakakorehia te raihana a Industry Canada. Ko te mahi kei raro i nga tikanga e rua e whai ake nei: (1) kare pea tenei taputapu e whakaporearea, me (2) me whakaae tenei taputapu ki nga pokanoa, tae atu ki te pokanoa ka puta he mahi kino o te taputapu.

WHAKAARO
This radio transmitter, the Sensus CL201, has been approved by Industry Canada to operate with the antenna types listed below, with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.

WHAKAARO
I raro i nga ture Ahumahi Canada, ka taea noa e tenei kaiwhakawhiti reo irirangi te mahi ma te whakamahi i te antenna o te momo me te whiwhinga morahi (he iti ake ranei) kua whakaaetia mo te kaiwhakawhiti e Ahumahi Canada. Hei whakaiti i te wawaotanga o te reo irirangi ki etahi atu kaiwhakamahi, me tino whiriwhiri te momo antenna me ona taonga kia kore e nui ake te mana o te irirangi irirangi (eirp) i tera e tika ana mo te whakawhitiwhitinga angitu.

WHAKATOKANGA
There is a danger of explosion if batteries are mishandled or incorrectly replaced. On systems with replaceable batteries, replace only with the same manufacturer and type or equivalent type recommended per the instructions provided in the product service manual.
Kaua e wetewete i nga pākahiko, ka ngana ranei ki te whakakii i waho o te punaha. Kaua e maka atu nga pākahiko ki te ahi.
Horoihia nga pākahiko kia rite ki nga tohutohu a te kaihanga me nga ture o te rohe.

WHAKATOKANGA
KAUA E WHAKANUI, ka tukuna ranei nga pūtau pākahiko ki te pāmahana neke atu i te 212°F. Ka taea e enei maimoatanga te pakaru o nga pūtau.

WHAKATOKANGA
EXPLOSION HAZARD – BATTERIES MUST ONLY BE CHANGED IN AN AREA KNOWN TO BE NON-HAZARDOUS.

xylem.com
SENSUS | 637 Davis Drive | Morrisville, NC 27560 | 800.638.3748 | Sensus.com

©2026 Sensus. All products purchased and services performed are subject to Sensus’ terms of sale, available at either sensus.com/TC or 1-800-638-3748. Sensus reserves the right to modify these terms and conditions in its own discretion without notice to the customer. The Sensus logo is a registered trademark of Sensus.
This document is for informational purposes only, and SENSUS MAKES NO EXPRESS WARRANTIES IN THIS DOCUMENT. FURTHERMORE, THERE ARE NO IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, WARRANTIES AS TO FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY. ANY USE OF THE PRODUCTS THAT IS NOT SPECIFICALLY PERMITTED HEREIN IS PROHIBITED.