intermatic.com
Intermatic.comIntermatic.com/support
intermatic.com/Policies
Installation Guide for INTERMATIC models including: SH-ABIWS1-WH In-Wall Wi-Fi Smart Switch, SH-ABIWS1-WH, In-Wall Wi-Fi Smart Switch, Wi-Fi Smart Switch, Smart Switch, Switch
Intermatic Inc ABIWS1 In-Wall Wi-Fi Smart Switch DGZABIWS1 DGZABIWS1 abiws1
File Info : application/pdf, 2 Pages, 798.31KB
DocumentDocumentLibertyville, Illinois 60048 www.Intermatic.com In-Wall Wi-Fi Smart Switch Quick Installation Guide SH-ABIWS1-WH In-Wall Wi-Fi Smart Switch LIMITED WARRANTY RATINGS SINGLE-POLE WIRING This warranty service is available by either (a) returning the product to the point of purchase or (b) by completing a warranty claim online at www. intermatic.com. You are required to provide a receipt, the model number and/or serial number when exercising this limited warranty. This warranty is made by: Intermatic Incorporated, 1950 Innovation Way, Suite 300, Libertyville, IL 60048. For warranty service go to: http://www. Intermatic.com or call 815-675-7000. Operating Voltage General Purpose Inductive Ballast Tungsten/Incandescent Electronic Ballast/LED Driver Motor Load Max. Load Rating 120-277 VAC, 50/60 Hz 15A 10A 15A 10A 1 HP @ 120 VAC 3 HP @ 240 VAC 1800W @ 120 VAC Box 1 Wi-Fi Switch Load Line Ground Neutral Traveler The Intermatic ABRA App EULA and Privacy Policy can be found at https://www.intermatic.com/Policies WARNINGS/SAFETY WARNING Risk of Fire or Electric Shock · Disconnect power at the circuit breaker(s) or disconnect switch(es) before installing or servicing. Wire Configuration Operation Temp. Range Dimensions (L x W x D) Warranty Single Pole & 3-Way 32°F to 104°F (0°C to 40°C) 4.125"H x 1.75" W x 1.25" D (to rear of mounting plate) 2 Year Limited BOX CONTENTS Purpose of CONTROL: MANUAL CONTROL Method of providing earthing of CONTROL: Ground terminal Blue Black Line 120-277 VAC Power Source Neutral / Line 2 Red White Green Ground To Load · Installation and/or wiring must be in accordance with national and local electrical code requirements. · Only use copper conductors rated 105°C minimum. · To prevent danger from explosion or leakage, do not throw batteries into fire or expose them to excessive heat. · To be installed in single- and double-gang with 2-1/2" minimum depth. Please consult a qualified electrician for specific wiring details. · Install only to a receptacle protected by 20A branch circuit overcurrent protection NOTICE ACTION: type 1.B ACTION; MICRO-DISCONNECTION on OPERATION CONTROL POLLUTION DEGREE: POLLUTION DEGREE 2, RATED IMPULSE VOLTAGE: 2500V" GETTING STARTED 1. Download the Intermatic ABRA App from the Google Play Store or App Store. 2. Scan the QR code to view the product page on our website. www.Intermatic.com/Product/SH-ABIWS1-WH Wire Blue Black Green White Red Description Connects to Load Connects to Line Connects to Ground Connects to Neutral or Line 2 Not used. Cap the wire. · Neutral wire required. For additional support, visit www.Intermatic.com/support CERTIFICATION AND COMPLIANCE THREE-WAY WIRING - EXAMPLE 1 This device complies with part 15 of the FCC. Operation is subject to the following two conditions: (1) this device may not cause harmful Wi-Fi Switch Downstream from the Remote Switch interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful Common Terminal Box 1 Ground Existing Remote Switch Box 2 Wi-Fi Switch interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. Line 120-277 VAC Power Source Neutral / Line 2 No Longer Used Blue Black · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to Ground · wCohnicshultthteheredceeaivleerr iosr caonnenxepceteride.nced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Cet équipement est conforme aux limites d'exposition aux rayonnements de la FCC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec une distance minimale de 20 cm entre le radiateur et votre corps. L émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L exploitation est autorisée aux deux conditions suivantes: 1.L appareil ne doit pas produire de brouillage ; 2.L appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d en compromettre le fonctionnement. Wire Blue Black Green White Red Description Connects to Load Connects to Line Connects to Ground Connects to Neutral or Line 2 Connects through remote switch to Line from power source Load Line Ground Neutral Traveler Load Line Ground Neutral Traveler THREE-WAY WIRING - EXAMPLE 2 Wi-Fi Switch Upstream from the Remote Switch Box 1 Wi-Fi Switch Common Terminal Box 2 Existing Remote Switch Red White Green To Load Blue Black Line 120-277 VAC Power Source Neutral / Line 2 Red White Green Ground Wire Blue Black Green White Red Description Connects to Load Connects to Line Connects to Ground Connects to Neutral or Line 2 Connects through remote switch to Line from power source Ground No Longer Used To Load This Class B digital apparatus complies with ICES-005 of Canada. FRENCH Libertyville, Illinois 60048 www.Intermatic.com In-Wall Wi-Fi Smart Switch Quick Installation Guide SH-ABIWS1-WH In-Wall Wi-Fi Smart Switch LIMITED WARRANTY RATINGS SINGLE-POLE WIRING This warranty service is available by either (a) returning the product to the point of purchase or (b) by completing a warranty claim online at www. intermatic.com. You are required to provide a receipt, the model number and/or serial number when exercising this limited warranty. This warranty is made by: Intermatic Incorporated, 1950 Innovation Way, Suite 300, Libertyville, IL 60048. For warranty service go to: http://www. Intermatic.com or call 815-675-7000. Operating Voltage General Purpose Inductive Ballast Tungsten/Incandescent Electronic Ballast/LED Driver Motor Load Max. Load Rating 120-277 VAC, 50/60 Hz 15A 10A 15A 10A 1 HP @ 120 VAC 3 HP @ 240 VAC 1800W @ 120 VAC Box 1 Wi-Fi Switch Load Line Ground Neutral Traveler The Intermatic ABRA App EULA and Privacy Policy can be found at https://www.intermatic.com/Policies WARNINGS/SAFETY WARNING Risk of Fire or Electric Shock · Disconnect power at the circuit breaker(s) or disconnect switch(es) before installing or servicing. Wire Configuration Operation Temp. Range Dimensions (L x W x D) Warranty Single Pole & 3-Way 32°F to 104°F (0°C to 40°C) 4.125"H x 1.75" W x 1.25" D (to rear of mounting plate) 2 Year Limited BOX CONTENTS Purpose of CONTROL: MANUAL CONTROL Method of providing earthing of CONTROL: Ground terminal Blue Black Line 120-277 VAC Power Source Neutral / Line 2 Red White Green Ground To Load · Installation and/or wiring must be in accordance with national and ACTION: type 1.B ACTION; MICRO-DISCONNECTION on OPERATION Wire Description local electrical code requirements. · Only use copper conductors rated 105°C minimum. · To prevent danger from explosion or leakage, do not throw batteries into fire or expose them to excessive heat. CONTROL POLLUTION DEGREE: POLLUTION DEGREE 2, RATED IMPULSE VOLTAGE: 2500V" GETTING STARTED Blue Black Green Connects to Load Connects to Line Connects to ground · To be installed in single- and double-gang with 2-1/2" minimum 1. Download the Intermatic ABRA App from the Google Play Store or App Store. White Connects to Neutral or Line 2 depth. Please consult a qualified electrician for specific wiring details. 2. Scan the QR code to view the product page on our website. Red Not used. Cap the wire. · Install only to a receptacle protected by 20A branch circuit overcurrent protection www.Intermatic.com/Product/SH-ABIWS1-WH NOTICE · Neutral wire required. For additional support, visit www.Intermatic.com/support CERTIFICATION AND COMPLIANCE This device complies with part 15 of the FCC. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Cet équipement est conforme aux limites d'exposition aux rayonnements de la FCC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec une distance minimale de 20 cm entre le radiateur et votre corps. L émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L exploitation est autorisée aux deux conditions suivantes: 1.L appareil ne doit pas produire de brouillage ; 2.L appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d en compromettre le fonctionnement. THREE-WAY WIRING - EXAMPLE 1 Wi-Fi Switch Downstream from the Remote Switch Common Terminal Box 1 Ground Existing Remote Switch Box 2 Wi-Fi Switch Line 120-277 VAC Power Source Neutral / Line 2 No Longer Used Blue Black Ground Wire Description Blue Connects to Load Black Connects to Line Green Connects to ground White Connects to Neutral or Line 2 Red Connects through remote switch to Line from power source Load Line Ground Neutral Traveler Load Line Ground Neutral Traveler THREE-WAY WIRING - EXAMPLE 2 Wi-Fi Switch Upstream from the Remote Switch Box 1 Wi-Fi Switch Common Terminal Box 2 Existing Remote Switch Red White Green To Load Blue Black Line 120-277 VAC Power Source Neutral / Line 2 Red White Green Ground Wire Description Blue Connects to Load Black Connects to Line Green Connects to ground White Connects to Neutral or Line 2 Red Connects through remote switch to Line from power source Ground No Longer Used To Load This Class B digital apparatus complies with ICES-005 of Canada. SPANISH Libertyville, Illinois 60048 www.Intermatic.com In-Wall Wi-Fi Smart Switch Quick Installation Guide SH-ABIWS1-WH In-Wall Wi-Fi Smart Switch LIMITED WARRANTY RATINGS SINGLE-POLE WIRING This warranty service is available by either (a) returning the product to the point of purchase or (b) by completing a warranty claim online at www. intermatic.com. You are required to provide a receipt, the model number and/or serial number when exercising this limited warranty. This warranty is made by: Intermatic Incorporated, 1950 Innovation Way, Suite 300, Libertyville, IL 60048. For warranty service go to: http://www. Intermatic.com or call 815-675-7000. Operating Voltage General Purpose Inductive Ballast Tungsten/Incandescent Electronic Ballast/LED Driver Motor Load Max. Load Rating 120-277 VAC, 50/60 Hz 15A 10A 15A 10A 1 HP @ 120 VAC 3 HP @ 240 VAC 1800W @ 120 VAC Box 1 Wi-Fi Switch Load Line Ground Neutral Traveler The Intermatic ABRA App EULA and Privacy Policy can be found at https://www.intermatic.com/Policies Wire Configuration Operation Temp. Range Dimensions (L x W x D) Single Pole & 3-Way 32°F to 104°F (0°C to 40°C) 4.125"H x 1.75" W x 1.25" D (to rear of mounting plate) Blue Black Line Red White Green WARNINGS/SAFETY WARNING Risk of Fire or Electric Shock Warranty 2 Year Limited BOX CONTENTS Purpose of CONTROL: MANUAL CONTROL 120-277 VAC Power Source Neutral / Line 2 Ground To Load · Disconnect power at the circuit breaker(s) or disconnect switch(es) before installing or servicing. · Installation and/or wiring must be in accordance with national and Method of providing earthing of CONTROL: Ground terminal ACTION: type 1.B ACTION; MICRO-DISCONNECTION on OPERATION Wire Description local electrical code requirements. · Only use copper conductors rated 105°C minimum. CONTROL POLLUTION DEGREE: POLLUTION DEGREE 2, RATED IMPULSE VOLTAGE: 2500V" Blue Connects to Load Black Connects to Line · To prevent danger from explosion or leakage, do not throw batteries into fire or expose them to excessive heat. · To be installed in single- and double-gang with 2-1/2" minimum GETTING STARTED 1. Download the Intermatic ABRA App from the Google Play Store or App Store. Green Connects to ground White Connects to Neutral or Line 2 depth. Please consult a qualified electrician for specific wiring details. 2. Scan the QR code to view the product page on our website. Red Not used. Cap the wire. · Install only to a receptacle protected by 20A branch circuit overcurrent protection NOTICE www.Intermatic.com/Product/SH-ABIWS1-WH · Neutral wire required. For additional support, visit www.Intermatic.com/support CERTIFICATION AND COMPLIANCE THREE-WAY WIRING - EXAMPLE 1 This device complies with part 15 of the FCC. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Cet équipement est conforme aux limites d'exposition aux rayonnements de la FCC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec une distance minimale de 20 cm entre le radiateur et votre corps. L émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L exploitation est autorisée aux deux conditions suivantes: 1.L appareil ne doit pas produire de brouillage ; 2.L appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d en compromettre le fonctionnement. Wi-Fi Switch Downstream from the Remote Switch Common Terminal Box 1 Ground Existing Remote Switch Box 2 Wi-Fi Switch Line 120-277 VAC Power Source Neutral / Line 2 No Longer Used Blue Black Ground Wire Blue Black Green White Red Description Connects to Load Connects to Line Connects to ground Connects to Neutral or Line 2 Connects through remote switch to Line from power source Load Line Ground Neutral Traveler Load Line Ground Neutral Traveler THREE-WAY WIRING - EXAMPLE 2 Wi-Fi Switch Upstream from the Remote Switch Box 1 Wi-Fi Switch Common Terminal Box 2 Existing Remote Switch Red White Green To Load Blue Black Line 120-277 VAC Power Source Neutral / Line 2 Red White Green Ground Wire Blue Black Green White Red Description Connects to Load Connects to Line Connects to ground Connects to Neutral or Line 2 Connects through remote switch to Line from power source Ground No Longer Used To Load This Class B digital apparatus complies with ICES-005 of Canada. INTERMATIC INCORPORATED | 1950 Innovation Way, Suite 300 | Libertyville, Illinois 60048 | www.Intermatic.com 158--02775