Mesqool CR01001eM Extra Loud Dual Alarm Clock with Vibration User Manual
Mesqool CR01001eM Extra Loud Dual Alarm Clock with Vibration

LOCATION OF CONTROLS

Product Overview

  1. Set Time & 12/24H ButtonHour Button
  2. Minute Button
  3. Dimmer & DST Button
  4. OK & SNOOZE Button
  5. Alarm Pause Button
  6. Alarm OFF Button
  7. Alarm 1 Button
  8. Alarm 2 Button
  9. PM Indicator
  10. Alarm 1 Indicator
  11. Alarm 2 Indicator
  12. DST Indicator
    Note: Batteries are notincluded
  13. Bell Indicator
  14. Vibrator Indicator
  15. Bell & Vibrator Toggle Button
  16. Volume + Button
  17. Volume – Button
  18. Battery Compartment
  19. USB Port
  20. DC Jack
  21. Vibrator Insert Port
  22. Holder (x 2pcs)
  23. Speaker
  24. Vibrator

POWER RESOURCES

Insert the two included holders into the back of the clock to avoid it being knocked over.

  1. Install 2pcs 1.5V “AAA” size batteries to the proper terminals in the battery compartment to memorize the time setting in case of power outage.
    NOTE: Batteries(not included) don’t support time display but can memorize time & alarm setting and trigger an alarm in case of AC power failure.
  2. Connect the adapter line to DC jack, then plug into a 100~240V ACwall power outlet.

TIME SETTING

  1. Press Time Setting button once, display Time Setting starts flashing.
  2. Press Time Setting button to set the hour press Time Setting button to set the minute.
  3. Press Time Setting button or Time Setting button to save time or wait for 5 seconds to confirm automatically.
  4. To change 12H/24H time format Hold press Time Setting button to switch 24H time format. Hold pressTime Setting button again to switch 12H time format.

ALARM SETTING

Set the Alarm

  1. Press Set the Alarm button, the alarm indicator Set the Alarm will light up, the display – starts flickering.
  2. Press Set the Alarm button to set the hour, press Set the Alarm button to set the minute.
  3. Press Set the Alarm button or Time Setting button to save alarm time or just wait for another 5 seconds to confirm automatically or.
  4. Push Set the Alarm or Set the Alarm  button to adjust alarm volume.

Setting ALARM 2 is the same as ALARM 1.

Turn off Alarm

When alarm goes off: 

  1. Press Time Setting button to temporarily turn off alarm for 9 minutes. Alarm will ring every next 9 minutes.
  2. Press Set the Alarm button to turn off today’s alarm.
    The alarm indicator Set the Alarm or Set the Alarm is still on, which means alarmis still activated and will ring after 24 hours
  3. Cancel Alarm
    • Press Set the Alarm button to turn off alarm 2 permanently, corresponding indicator Set the Alarm turn off. Press Set the Alarm button again to turn off alarm 1 permanently, corresponding indicator G} will turn off.
    • If alarm 1 goes off, then press Set the Alarm button, just turn off alarm1 permanently. Set the Alarm indicator will turn off.
    • If alarm 2 goes off, then press Set the Alarm button, just turn off alarm 2 permanently. Set the Alarm indicator will turn off.

DIMMER

Repeatedly press Set the Alarm button to adjust the brightness of display for your preference.

There are 5 levels, The sequence is as follows:
3-4-5-4-3-2-1-2-3……..

DST

Hold press Set the Alarm button to switch to DST function.
DST indicator will turn on.
Hold press Set the Alarm button again to turn off DST function.
DST indicator will turn off.

USB CHARGING

Plug charging cable into device such as phone or tablet.
Device can charge your phone or tablet at the same time.

The maximum charge currents 1 Ampere.
USB Charging

Vibrator

  1. Insert the vibrator plug into the vibrator jack of the machine, the bell indicator and the vibrator indicator will light up, indicating that the bell and the vibrator will be effective at the same time.
    USB Charging
  2. Press Set the Alarm button, the ring indicator Set the Alarm goes off, and the vibrator indicator Set the Alarm stays on, which means that when the alarm goes off, the vibrator will take effect, but the bell will not sound.
  3. Press Set the Alarm button again, the ring indicator Set the Alarm goes on, and the vibrator indicator Set the Alarm goes off, which means that when the alarm goes off, the bell will sound, but the vibrator will not shake.
  4. Press Set the Alarm button again, the ring indicator Set the Alarm and the vibrator indicator Set the Alarm goes on, which means that when the alam goes off, the bell and the vibrator will be effective at the same time.

2-3-4 will continue to loop.

Contact our expert

Amazon.ca: support-ca@mesqool.com
Amazon.com: support-us@mesqool.com

http://www.mesqool.com

Mesqool Logo

Documents / Resources

Mesqool CR01001eM Extra Loud Dual Alarm Clock with Vibration [pdf] User Manual
CR01001eM Extra Loud Dual Alarm Clock with Vibration, CR01001eM, Extra Loud Dual Alarm Clock with Vibration, Dual Alarm Clock with Vibration, Alarm Clock with Vibration, Clock with Vibration

References

Leave a comment

Your email address will not be published. Required fields are marked *