MERLYN MIND MUDG3 Merlyn Display Remote Control
What’s in the box
- Safety Certifications
- User Guide
- Two AA Batteries
- Remote
- USB Receiver with Antenna
- Lanyard comes unattached
Installation
- Straighten the Merlyn USB Dongle (See page 2)
- Connect the USB Receiver to the Android USB3.0 port on the bottom side of the rear of the panel.
Ports on bottom side of Q21 panel
Ports on bottom side of Q23 panel
- Make sure that the antenna is pointing down and there is a clear line of sight from the antenna to the RCU.
Before using the remote control, ensure the batteries are loaded and pull tab has been removed.
Merlyn Display Software
Before downloading the software, your district will need to purchase Merlyn Display licenses from an authorized vendor. After purchasing the licenses, your district will gain access to the Management Console to register your panels and manage your software. This step should occur before you download the software to the panel.
The Merlyn Display software can be downloaded from the Newline App store on your panel. Depending on access settings, your display may require administrator approval to download the software.
After downloading the software, the Merlyn Display App will present you with a QR code to register in the Management Console. This is required to enable the software on the display.
Not sure if Merlyn is running
Try holding down the Push-to-Talk button ( ) and asking, “How’s the weather?” If you hear a response, then Merlyn is ready to use!
If you don’t get a response, try pressing the orange Merlyn Menu button toward the top of the remote to see notifications that will guide you to finish setup. If you do not see the Merlyn toolbar or notifications in the top right of your screen when you click the button, please click “apps” on your panel home screen and looking for an app called “Merlyn.” If you see it, click the app to start it. If it is not there, please contact your IT Administrator for help.
Get started using Merlyn
Press the Push-to-Talk button ( ) and then hold it down while you talk to Merlyn. Try some voice requests:
Ask questions
“What time is it?”
“Who is George Washington?”
“How many cups are in a pint?
Open and search websites
“Open YouTube”
“Search Google for the Pythagorean Theorem”
“Open Khan Academy”
“Search Newsela for California”
Control your panel and panel apps
“Start a timer for 2 minutes“
“Open whiteboard /
Close whiteboard“
“Switch to HDMI1”
“Increase brightness”
“Volume up”
“Freeze screen“
This code will take you to the Merlyn Display Support page. There, you can find guides for installation, Remote control usage, how to get started, and support when you need it
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.
Fcc Statement
This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions:(1)this device may not cause harmful interference,and(2)this device must accept any interference received,including interference that may cause undesired operation.
CAUTION:Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment
NOTE:This equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates,uses,and can radiate radio frequency energy and,if not installed and used in accordance with the instructions,may cause harmful interference to radio communications.However,there is no guarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception,which can be determined by turning the equipment off and on,the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna
- Increase the separation between the equipment and receiver
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
- Consult the dealer or an experienced radio/TV technician for help
ISED Statement /Declaration ISED
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation,Science and Economic
Development Canada’s licence-exempt RSS(s).Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference,including interference that may cause undesired operation of the device
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment.
Customer Support
merlyn.org/startdisplay
support@merlyn.org
merlynmind.ai/support
Documents / Resources
 |
MERLYN MIND MUDG3 Merlyn Display Remote Control [pdf] User Guide MUDG3, 2AYDX-MUDG3, 2AYDXMUDG3, MUDG3 Merlyn Display Remote Control, MUDG3, Merlyn Display Remote Control, Display Remote Control, Remote Control |