memorex MX-MCD200 Bluetooth CD Micro System with FM Radio Instruction Manual

Main Unit: Unwind the AC power cord and extend it to its full
length. Insert the AC plug of the cord into any convenient AC
120V~; 60Hz household outlet.

Battery Installation:

Open the battery door on the bottom of the unit by pressing the
tab and lifting it.
Insert two (2) AAA size batteries (not included) according to
the polarity diagram inside the battery compartment. Alkaline
batteries are recommended.

Replace the battery door.

Remote Control Setup:

Open the battery door on the bottom of the remote control by
pressing the tab and lifting it.

Insert two (2) AAA size batteries (not included) according to
the polarity diagram inside the battery compartment. Alkaline
batteries are recommended.

Frequently Asked Questions (FAQ)

Q: What type of batteries does the unit require?

A: The main unit requires two (2) AAA size batteries, while the
remote control also requires two (2) AAA size batteries. Alkaline
batteries are recommended for both.

Q: How do I connect the speaker boxes to the main unit?

A: Connect the small plug from the Speaker Boxes to the SPEAKER
OUT L & R Jacks on the rear of the main unit.

Q: What is the power source for the main unit?

A: The main unit is powered by an AC 120V~; 60Hz household
outlet. Ensure to unwind the AC power cord fully and insert it into
a suitable outlet.

“`

View Fullscreen

TOP LOADING BLUETOOTH CD PLAYER & FM RADIO
MODEL MX-MCD200 OPERATION MANUAL
PLEASE READ BEFORE OPERATING THIS EQUIPMENT

SPECIAL NOTES

For users in U.S.
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Explanation of Graphical Symbols:
an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage”
cient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

FOR YOUR RECORDS For your assistance in reporting this unit in case of loss or theft, please record below the model number and serial number which are located at the bottom of the unit.
Please retain this information. Model number __________________ Serial number ___________________ Date of purchase ________________ Place of purchase _______________
To obtain service or product information,
call 1-877-506-4900

FCC COMPLIANCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installtion. This equipment generates, uses and can radiate radio frequency energy and, if not Installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. CAUTION: To reduce the risk of electric shock, do not remove cover (or back). No userserviceable parts inside. Refer servicing to qualified service. FCC NOTICE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including that may cause undesired operation. FCC Radiation Exposure Statement: The product comply with the US portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

LOCATION OF CONTROLS
1 2
6

1. CD DOOR 2. CD Door OPEN (Close) Area
3. POWER Button 4. FUNCTION Button 5. REPEAT Button 6. PROG (Program) Button
7. (Previous/Skip Backward) Button
8. LCD Display
9. (Next/Skip Forward) Button
n
10. (Stop) Button 11. (Play/Pause) Button
12. VOLUME – Button 13. VOLUME + Button

14. TREBLE Control Knob 15. AL SET (Alarm Set) Button 16. MUTE Button 17. DIMMER Button 18. AL ON/OFF (Alarm On/Off) Button 19. BASS Control Knob 20. TIME (Set) Button 21. P- Button 22. P+ Button 23. SLEEP/SNOOZE Button 24. POWER Indicator 25. Remote Receiver 26. AUX-IN Port

1. FM Wire Antenna 2. SPEAKER OUT R (Right) Jack

23 4
3. SPEAKER OUT L (Left) Jack 4. AC Power Cord
7

Battery Door

1. REPEAT Button 2. (Play/Pause) Button
3. (Previous/Skip Backward) Button

4. (Stop) Button 5. (Next/Skip Forward) Button
6. Battery Holder

CONNECTION:
Connect the small plug from the Speaker Boxes to the SPEAKER OUT L & R Jacks on the rear of main unit as the illustrated below:
POWER SOURCE:
Main Unit: Unwind the AC power cord and extend it to its full length. Insert the AC plug of the cord into any convenient AC 120V~; 60Hz household outlet as the illustrated below:
9

Notes: z This unit is equipped with a polarized AC plug which has one blade wider than
the other. This is a safety feature to reduce the likelihood of electric shock. This polarized AC plug will only fit in a polarized AC outlet. If you find that you cannot insert this plug into your outlet, you may have an obsolete non-polarized outlet. Please do not try to defeat this safety feature by using a non-polarized adaptor or by filling the wider blade to make it fit into your outlet. If this plug does not fit into your outlet, you should contact a qualified licensed electrician to replace your obsolete outlet. z If the AC power fails, this electronic clock is designed to continue operating internally (without showing the time on the LCD Display) with two (2) AAA size batteries (not included). Install the batteries as follows:
Open the battery door on the bottom of the unit by press the tab and then lifting it as illustrated below:
Insert two (2) AAA size batteries (not included) according to the polarity diagram inside the battery compartment. (Alkaline batteries are recommended.)
Replace the battery door.
10

REMOTE CONTROL:
First time use:
z Open the battery door on the bottom of the remote control by press the tab and then lifting it as illustrated below.
z Insert two (2) AAA size batteries (not included) according to the polarity diagram in side the battery compartment. (Alkaline batteries are recommended.)
z Replace the battery door.

BATTERY PRECAUTIONS:
Follow these Battery Precautions when using a battery in this device:
1. Use only the size and type of battery specified. 2. Be sure to follow the correct polarity when installing the battery as indicated in the
battery compartment. A reversed battery may cause damage to the device. 3. Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc) or
old batteries with fresh ones. 4. If the batteries in the device are consumed or the device is not to be used for a
long period of time, remove the batteries to prevent damage or injury from
11

possible battery leakage.

5. Do not try to recharge the battery not intended to be recharged; it can overheat

and rupture. (Follow battery manufacturer’s instructions.)

6. Do not dispose of battery in fire. Battery may explodes or leak.

7. Clean the battery contacts and also those of the device prior to battery installation.

This product contains a coin/button cell battery. If the coin/button cell

battery is swallowed, it can cause severe internal burn in just 2 hours and can lead

to death.

Keep new and used batteries away from children. If the battery compartment does

not close securely, stop using the product and keep it away from children.

If you think batteries might have been swallowed or placed inside any part of the

body, seek immediate medical attention.

EFFECTIVE DISTANCE OF REMOTE CONTROL

<±45° 25 Feet

z When there is an obstacle blocking between the sensor, the remote may not work.
z When direct sunlight, or any other strong light shines on the remote control, the remote operation may be unstable.

OPERATION

GENERAL OPERATION:

1. Connect the unit to AC power as previously instructed. The unit will enter to

standby mode automatically and the LCD Display will illuminate.

2. Press the POWER Button on the main unit or remote control to turn on the unit

from standby mode. The POWER Indicator will illuminate.

3. Press the FUNCTION Button on the main unit or remote control repeatedly to

switch to desired playback mode. The correspondent indicator will appear on

the display with your selection (see list below):

Playback Mode:

Indicators:

CD BT (Bluetooth) AUX FM AM

“Cd” will appear on the display “bt” will appear on the display “AUX” will appear on the display “FM” will appear on the display “AM” will appear on the display

4. During playback, z Turn the VOLUME + / VOLUME – button on the unit to adjust volume level as desired. z Turn the BASS control knob to enhance the bass of the sound to the speakers

5. Press the DIMMER Button on the main unit or remote control repeatedly to set the brightness level of display.
6. When finished listening, press the POWER Button on the unit or remote control to turn back to standby mode.
CLOCK:
To set or reset the time:
In Standby mode, press and holding the TIME SET Button on main unit or remote control, time on display will blinking. Then:
z Press the or Button on the main unit or remote control to set hour. (Make sure the PM Indicator appearing on the display if the time is PM).
z Press the TIME SETButton on the main unit or remote control again on the unit to set minute.
z Press the or Button on the main unit or remote control to set minute. z When finished settings, release the TIME SET Button on the main unit or
remote control to save the settings and exit, time on display will stop blinking.

ALARM SET:

To set or reset the alarm time:

In Standby mode, press and holding the AL SET (Alarm Set)Button on the main unit or remote control, alarm time will appear on the display and blinking. Then:

z Press the or Button on the main unit or remote control to set hour. (Make sure the PM Indicator appearing on the display if the alarm time is PM).

Press the AL SET Button on the main unit or remote control again on the unit to set z minute.

PressAL SET Button on the main unit or remote control to select wake up mode.

z Press the or

Button on the main unit or remote control to select wake up

mode.

CD – Wake up by CD

BU – Wake up by Buzzer

FM – Wake up by FM Radio

AM – Wake up by AM Radio

z Press the AL ON/OFF (Alarm On/Off) Button to activate alarm. The ” ” Indicator will appear on the display.

To set or reset the wake up mode: In alarm on mode, press and holding the AL SET Button, alarm time will appear on the display
and blinking. Press the AL SET Button at the same time repeatedly to set or reset the wake up mode as desired.
Notes: 1. After setting, press the AL SET Button to read the Alarm time. 2. Alarm will not operation when the unit is in power on mode. 3. If radio wake up mode was selected, received the desired radio station as previous
procedure and also set the desired volume level before activate alarm. Otherwise, when Alarm goes off, no sound output from the speaker or sound weak. 4. If CD wake up mode was selected, make sure you were placed the desired CD disc in the unit and sound level was set to suitable level. Otherwise, when Alarm goes off, no sound output from the speaker or sound weak.
Shut off alarm: z When alarm goes off, press the AL ON/OFF Button on the unit once. Alarm
will turn on again on next day. z To turn off alarm completely (alarm will not turn on next day), press the AL.
ON/OFF Button repeatedly until all the correspondence alarm indicators disappear on the display.
Sleep: z Power the unit and press the SLEEP/SNOOZE Button to adjust the timer.
You can select 120, 90, 60, 30, 20, 10 minutes or OFF. z Once the set sleep time has expired the clock radio will automatically power
off.

Snooze: z When the alarm sounds, tap the SLEEP/SNOOZE BUTTON to temporarily
turn off the alarm and activate the snooze function, the alarm will stop and sound again 9 minutes later. If you tap the SLEEP/SNOOZE BUTTON again, the alarm will temporarily turn off again and sound again in 9 minutes and so on.

CD:

CD Playback:

1. Open the CD door by press the CD OPEN (Close) area. 2. Place a CD disc on the center spindle, with the printed label side up. 3. Close the CD Door by press the CD OPEN (Close) area. 4. Power on the unit and enter to CD mode as previously instructed. “Cd” indicator
will appear on the display. 5. Wait a few seconds until the total number of tracks appears on the display. Then
press the Play/Pause Button on the unit or Remote Control to start playback. 6. During playback:
z Press the Play/Pause Button on the unit or Remote Control to pause, press again to resume normal playback.
z Press the (Next/Skip Forward) or (Previous/Skip Backward) Buttons on the unit or Remote Control repeatedly to skip tracks.
z Press and holding the (Next/Skip Froward) or (Previous/Skip Backward) Buttons on the unit or Remote Control repeatedly to fast searching the specified section.
z To stop, press the (Stop) Button on the unit or Remote Control.

Repeat / Random Playback :

1. During playback, press the REPEAT Button on the unit or Remote Control once.

”

” indicator will appear on the display. The current track will playback

repeatedly.

2. During playback, press the REPEAT Button twice. ”

” indicator will

appear on the display. All the tracks on the current disc will be playback

repeatedly.

3. During playback, press the REPEAT Button three times. ”

” indicator will

appear on the display. All the tracks on the current disc will be playback

randomly.

4. To cancel the Repeat/Random function, press the REPEAT Button repeatedly

until all the repeat indicators disappear on the display.

Programmed Playback:

Up to 20 tracks can be programmed playback as follows:

1. In CD stop playing mode, press the PROG (Program) Button on main unit or remote control. “P01” will appear on the display and PROG indicator will blink.
2. Select the first specific track to be programmed by pressing the (Next/Skip Forward) or (Previous/Skip Backward) Buttons on the unit or Remote Control repeatedly.
3. Press the PROG Button again to store the selected track into the memory. 4. Repeat steps 2 and 3 until all the specific tracks stored into the memory. 5. Press the Play/Pause Button on the unit or Remote Control to start program
playback. 6. To stop press the (Stop) Button on the unit or Remote Control once. “PROG”
indicator will remain on the display. Then press Button to start program playback again. 7. To stop and cancel the program, press the (Stop) Button on the unit or Remote Control twice. “PROG” indicator on the display will disappear.
BT (BLUETOOTH) :
BT (Bluetooth) pairing First time use or re-pairing the unit to a new BT Device, pair as follows:
1. Power on the unit and enter to BT mode as previously instructed. “bt” indicator will appear on the display and blink.
2. Power on the external BT Device and enter to BT searching mode. Start pairing following the on screen instructions from the external BT Device. After paired, the “bt” indicator on the display will stop blinking.
3. If pairing is complete you may now play music with your external BT Device. 4. During playback:
z Press the Play/Pause Button on the unit or Remote Control to pause,
press again to resume normal playback.
z Press the (Next/Skip Forward) or (Previous/Skip Backward) Buttons
on the unit or Remote Control repeatedly to skip tracks.
Notes: z When the external BT Device searched the unit, model number “MX-MCD200”
will appear on the display of external BT Device. z If while pairing you are asked for a code, please try “0000” or “1234”.
Normal operation after pairing:
1. Turn on the BT function of the external BT Device. 2. Power on the unit and enter to BT mode as previously instructed. “bt” indicator
will appear on the display and blink. 3. Wait a few seconds until the unit is automatically paired to the external BT
Device. (“bt” indicator on the display will stop blinking). 4. After pairing is complete you may now play music with your external BT Device.
16

AUX IN:
1. Connect the external Audio Device with a 3.5mm AUX cable. (Cable not included).
2. Insert one end of the AUX cable to the Phone; Line Out or AUX Out Jack on the external Audio player.
3. Power on the unit from Standby mode by press the POWER Button on the unit to select AUX In mode. Insert the other end of the AUX cable into the AUX In Port on the front of unit. “AUX” indicator will appear on the display.
4. Play the music on the connected Player as usual. (Make sure the volume level of the connected Audio Player is turned to high level.)
AM/FM RADIO:
1. Power on the unit and enter to Radio mode as previously instructed. “AM” or “FM” indicator and the radio frequency will appear on the display.
2. Press the or Button to select the radio station as desired.

AUTO SCAN RADIO:
1. Press and hold Play/Pause Button for 2 seconds 2. The unit will auto scan available station in AM or FM band and store in the
preset memory. 3. To navigate through the stored presets, press the MEM+ or MEM- Buttons.

SETTING AM/FM RADIO PRESETS:

1. Find the AM/FM radio station you would like to save.

2. Press the PROGRAM Button on the main unit or PROGRAM Button on the remote control.

3. Press

or buttons to select the preferred Preset Number,The display will show

“P01, P02, etc…”

4. Press the PROGRAM Button on the main unit or press PROGRAM Button on remote control again to save the station.

5. Repeat steps 1-4 until you have finished saving your presets.

6. To navigate through the stored presets, press the P+ or P- Buttons.

Notes:

z If stereo FM radio station is receiving in FM band. The FM stereo indicator ”

”

will appear on the display automatically.

z This unit can store up to 30 FM radio stations and 20 AM radio stations presets

Antennas:
AM This unit has a build in ferrite rod antenna, which provides adequate reception in most areas. If reception is weak, turn the unit to improve reception. FM The FM Wire Antenna is for FM reception only. If reception is weak, unwound and relocation the wire antenna.

TROUBLESHOOTING

Check the following before requesting service:

SYMPTOM

POSSIBLE CAUSE

POSSIBLE SOLUTION

No power No sound or sound weak Sound distortion Alarm not functioning BT not functioning
CD not play Radio not function Radio reception not good

AC Power cord had not connected Plug the AC Cord to any wall

outlet having AC 120V~; 60Hz Volume of the unit was set to minimum Increase the volume level by

position

pressing the VOLUME + /

Volume level of paired/connected

VOLUME – button clockwise Rise the volume level of the

device is in low level Volume level too high

paired/connected device Reduce the volume level by

pressing the VOLUME –

button Volume level of the connected/paired Reduce the volume level of the

device too high Unit is not in standby mode

connected/paired device Press POWER button to turn

Unit not in BT mode

back to standby mode Press the FUNCTION Button

repeatedly until “bt” appear on

The external BT device had NOT

the display Pair the external BT Device to

paired to the unit The external BT device too far from

the unit as page 15 Place the external BT device

the unit Unit not in CD mode

close to the unit Press the FUNCTION Button

repeatedly until “Cd” appear on

CD disc incorrect install

the display Place the CD disc on the center

Disc is dirty or scratched

spindle with label side face up
Try other discs or clean the discs

Unit not in radio mode

Press the FUNCTION Button

repeatedly until “AM” or “FM”

indicator appear on the display The direction or location no good for Turn the unit to a new direction

radio reception

or replace the unit to a new

location 18

SPECIFICATTIONS

Power Source: Clock Back Up:
BT Version:

AC 120V~; 60Hz; 18W

3V; 2 x “AAA” size batteries (Not

included)

5.0

BT Operation Distance: <=32 Feet in open area

Radio Frequency:
Disc Compatible: Impedance of Speakers: Audio power:

AM: 520-1710kHz FM: 87.5-108MHz CD; CD-R; CD-RW 2 x 3W; 4ohm 2 x 2W (Total 4W, RMS)

ACCESSORIES
1 x User’s Manual 1 x Remote Control (Uses 2 x AAA batteries,no Included)
SPECIFICATIONS AND ACCESSORIES ARE SUBJECT TO CHANGE WITHOUT NOTICE

Documents / Resources

memorex MX-MCD200 Bluetooth CD Micro System with FM Radio [pdf] Instruction Manual
MX-MCD200 Bluetooth CD Micro System with FM Radio, MX-MCD200, Bluetooth CD Micro System with FM Radio, Micro System with FM Radio, FM Radio

References

User Manual

MX-MCD200 Bluetooth CD Micro System with FM Radio

Product Information

Specifications:

Product Usage Instructions

Connection:

Power Source: